Gebruiksaanwijzing /service van het product LC-XB21B van de fabrikant Eiki
Ga naar pagina of 68
Multimedia Projector Owner's Manual LC-XB21B MODEL.
2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology .
T able of Contents 3 T rademarks Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design . . . . . . . . . . . . . 2 T able of Contents . . . . . . . . . . .
4 T o the Owner Before operating this projector, read this manual thoroughly and operate the projector properly . This projector provides many convenient features and functions. Operating the projector properly enables y o u t o m a n a g e th o s e fe a t u r e s a n d ma i n t a i n s i t i n better condition for a considerable time.
5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
Safety Instructions 6 Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent.
Compliance 7 Federal Communications Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
8 Part Names and Functions ① Speaker ② Zoom Ring (rear side) ③ Infrared Remote Receiver ④ Focus Ring (front side) ⑤ Projection Lens ⑥ Lens Cover ⑦ Air Intake V ent ⑧ Exhaust V ents CAUTION Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side.
9 Part Names and Functions Part Names and Functions Rear T erminal ① SERVICE PORT This jack is used to service the projector . ② COMPUTER IN 1 / S-VIDEO IN /COMPONENT IN Connect output signal from a computer , RGB scart 21-pin video output, S-VIDEO output, or component video output to this terminal.
10 Part Names and Functions T op Control ⑦ LAMP REPLACE indicator T urn yellow when the life of the projection lamp draws to an end. (p.54, 61) ⑥ W ARNING indicator Emit a red light when the projector detects an abnormal condition. This also blinks red when the internal temperature of the projector exceeds the operating range.
1 1 Part Names and Functions Part Names and Functions ⑤ ③ ⑨ ⑬ ④ ⑭ ⑫ ⑩ ① ② Remote Control ⑥ ⑦ ⑧ ⑮ ⑪ ① POWER ON/ST AND-By button T urn the projector on or off. (p.18, 19) ② VIDEO button Select VIDEO input source. (p.23, 34) ③ COMPUTER button Select COMPUTER input source.
Part Names and Functions 12 T o ensure safe operation, please observe the following precautions: ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery . ● Avoid contact with water or liquid.
13 Installation Note: • The brightness in the room has a great influence on picture quality . It is recommended to limit ambient lighting in order to obtain the best image. • The values shown below are approximate and may vary from the actual sizes.
Installation 14 This projector uses nominal input voltages of 100-120 V or 200-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor . T o reduce the risk of electrical shock, do not plug into any other type of power system.
Installation 15 Connecting to a Computer Cables used for connection • VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) • Audio Cables (Mini Plug: stereo) ( Not all the cables are supplied with this projector .
Installation 16 Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-Video Cable • S-Video-VGA Cable • Audio Cables (RCA X 2, Mini Plug: stereo) ( Not all the cables are supplied with this projector .
Installation 17 Connecting to Component Video and RGB (Scart) Equipment Cables used for connection • Audio Cables (Mini Plug :stereo) • Scart-VGA Cable • Component Cable • Component-VGA Cable ( Not all the cables are supplied with this projector .
Basic Operation 18 Connect the projector's AC power cord into an AC outlet. The POWER indicator becomes red. Remove the lens cover . Press the POWER ON/ST AND-BY button on the top control or on the remote control. The POWER indicator becomes green and the cooling fans start to operate.
Basic Operation 19 Press the POWER ON/ST AND-BY button on the top control or on the remote control, and a message "Power off?" appears on the screen. Press the POWER ON/ST AND-BY button again to turn off the projector . The POWER indicator starts to blink red, and the cooling fans ke ep run n in g .
Basic Operation 20 How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedures. Press the Point ◄► buttons to select a Menu icon to adjust and press the Point ▲▼ buttons to select an item to adjust.
Basic Operation 21 Menu Bar PC System Menu Used to select computer system. (p.26) Setting Menu Used to set the projector's operating configurations. (p.41-50) Image Select Menu Used to select an image level among Dynamic, Standard, Real, Blackboard (Green), and Image 1 ~ 4.
Basic Operation 22 Rotate the Zoom Ring to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus. Zoom and Focus Adjustment Focus Ring (Front side) Zoom Ring (Rear side) POINT ▲▼ buttons KEySTONE button KEySTONE ▲▼ buttons • The arrows are white when there is no correction.
Basic Operation 23 Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds.
Basic Operation 24 black out the captured image normal • • • • • Press the NO SHOW button on the remote control to black out the image. T o restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the L ogo selection (p.
Computer Input 25 Input Source Selection Direct Operation Input Menu M o v e t h e p o i n t e r ( r e d arrow) to Computer 1 and press the SELECT button. Input Menu icon Move the pointer to RGB and press the SELECT button. Source Select Menu Computer 1 Press the MENU button to display the On-Screen Menu.
Computer Input 26 Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment.
Computer Input 27 Auto PC Adjustment function is provided to automatically adjust Fine sync, T otal dots, Horizontal, and V ertical to conform to your computer .
Computer Input 28 Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the PC Adjust Menu icon. Press the Point ▲ ▼ b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust and then press the SELECT button to display the adjustment dialog box.
Computer Input Press the Point ◄ ► buttons to adjust the horizontal area displayed by this projector . Display area H Press the Point ◄► buttons to adjust the vertical area displayed by this projector . Display area V Reset Store Exit the PC Adjust Menu.
30 Computer Input Select an image level among Dynamic, Standard, Real, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector . Picture level with improved halftone for graphics.
31 Computer Input Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the Image Adjust Menu icon. Press the Point ▲ ▼ b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust, and then press the SELECT button.
Computer Input 32 Store Exit the Image Adjust Menu. Quit T o store the adjusted data, select Store and press the SELECT button. Select a level from Image 1 to 4 with the Point ▲▼ buttons and press the SELECT button. A confirmation box appears and then select [Y es].
Computer Input 33 Whe n the D. ZOO M + ( ▲ ) is pressed, the On-Screen Menu disappears and the message "D. zoom +" is dis play ed. P ress t he D.Z OOM ▲ or th e SEL ECT button to expand the image size. And press the Point ▲▼◄► buttons to pan the image.
V ideo Input 34 Input Source Selection (Video) Direct Operation Remote Control VIDEO button Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the Input Menu icon. Press the Point ▲▼ buttons to move the red arrow pointer to Video and then press the SELECT button.
Computer 1 Video Input 35 Remote Control COMPUTER button Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below .
Video Input 36 Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the A V System Menu icon. Video System Selection Press the Point ▲▼ buttons to move the red arrow pointer to the syst em that you want to se lect and then press the SELECT button.
Video Input 37 Select an image level among Dynamic, Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector . Picture level adjusted for the picture with fine tone.
Video Input 38 Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the Image Adjust Menu icon. Press the Point ▲ ▼ b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust, and then press the SELECT button.
Video Input 39 T o reset the adjusted data, select Reset and press the SELECT button. The confirmation box appears and then select [Y es]. All adjustments returns to their previous figures. Reset Press the Point ◄► buttons to adjust the gamma value to obtain better balance of contrast.
Video Input 40 This projector has the picture screen resize function, which enables you to customize the image size. Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the Screen Menu icon.
Setting 41 Blue back Press the Point ◄► buttons to switch On/Off. When this function is "On", a blue image is displayed while the input signal is not detected. Keystone Press the MENU button to display the On-Screen Menu. Press the Point ◄► buttons to move the red framed pointer to the Setting Menu icon.
Setting 42 Display P r e s s t h e P o i n t ◄ ► b u t t o n s t o s w i t c h O n / O f f . T h i s function decides to display On-Screen Displays. O n ............. S h o w all the On-Screen Displays. Use this function when you want to p r o j e c t i m a g es a f t e r t h e l a m p becomes bright enough.
Setting 43 Capture This function enables you to capture the image being projected and use it for a start-up display or interval of presentations. After capturing the projected image, go to the Logo select function and set it to "User".
Setting 44 T o Enter the Logo PIN code Select a number by pressing the Point ▲▼ buttons. And then press the Point ► button to fix the number and move the pointer .
Setting 45 Ceiling Wh en t hi s fu n ct io n is " On ", t h e pi ct ur e is t op / bo tt om and left/right reversed. This function is used to project the image from a ceiling mounting the projector . Rear When this function is "On", the picture is left/right reversed.
Setting 46 Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period.
Setting 47 Remote control Th i s p r o j e c t o r p r o v id e s t w o d i f fe r e n t r e m o t e c o n tr o l codes: the factory-set initial code (Code 1) and the s econdary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.
Setting 48 Key lock Security (Key lock and PIN code lock settings) This function allows you to use Key lock and PIN code lock function to set the security for the projector operation. Thi s fu nct io n loc ks o per at ion o f th e top c on tro l or the remote control.
Setting 49 T o Enter the PIN code Select a number by pressing the Point ▲▼ buttons. And then press the Point ► button to fix the number and move the pointer .
Setting 50 This function is used to reset the lamp replacement counter . When replacing the projection lamp, reset the lamp replacement counter by using this function.
Maintenance and Cleaning 51 The W ARNING indicator shows the state of the function which protects the projector . Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance. W arning Indicator T h e p r o j e c t o r i s s h u t d o w n a n d t h e WA R N I N G indicator is blinking red.
Maintenance and Cleaning 52 T urn off the projector , and disconnect the AC power cord from the AC outlet. T urn over the projector and remove the air filters by pulling the latches upward. Air filters prevent dust from accumulating on the optical elements inside the projector.
Maintenance and Cleaning 53 Cleaning the Projector Cabinet Gently wipe the projector body with a soft, dry cleaning cloth. When it is heavily soiled, use a small amount of mild detergent and finish with a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner .
Maintenance and Cleaning 54 When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow , replace the lamp with a new one promptly .
Maintenance and Cleaning 55 B e s u r e to r e s e t t h e L a m p r e p l a c e m e n t c o u n t e r a f t e r t h e l a m p i s r e p l a c e d . W h e n t h e L a m p replacement counter is reset, the LAMP REPLACE indicator stops lighting. T urn the projector on, press the MENU button to display the On-Screen Menu.
Appendix 56 T roubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on pages15-17. – Make sure all equipment is connected to AC outlet and the power is turned on.
Appendix 57 Image is Left/Right reversed Image is T op/Bottom reversed – Check the Ceiling/Rear function. (See page 45.) – Check the Ceiling function. (See page 45.) No sound – Check audio cable connections from the audio input source. – Adjust the audio source.
Appendix 58 W ARNING: High voltages are used to operate this projector . Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center.
Menu T ree System (1) Mode 1 Mode 2 SVGA 1 - - - - Computer Input Systems displayed in the System Menu vary depending on the input signal. Computer Input/Video Input Sound On/Off Sound 0 - 63 Input Computer 1 RGB Go to System (1) Quit RGB (Scart) Component Go to System (3) V olume Mute Quit Auto PC Adj.
Appendix 60 Dynamic Cinema Blackboard (Green) Image 1 Image 2 Image 3 Image Select Image 4 Standard Video Input Auto P AL SECAM NTSC NTSC 4.43 P AL-M P AL-N Auto 1080i 1035i 720p 575p 480p 575i 480i System (2) System (3) Image Adjust Contrast Brightness Color temp.
Check the indicators for projector condition. Indicators and Projector Condition The projector is off. (The AC power cord is unplugged.) The projector is preparing for stand-by or the projection la m p i s be i ng c o o le d d o wn . Th e p ro j e ct o r ca n n ot b e turned on until cooling is completed.
Appendix 62 Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V , H-Frequency below mentioned and less than 1 10 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. MAC LC13 640 x 480 34.
T echnical Specifications Mechanical Information Projector T ype Multi-media Projector Dimensions (W x H x D) 12.99" x 3.15" x 9.33" (330 mm x 80 mm x 237 mm) (Not including protrusion) Net Weight 6.4 lbs (2.9 kg) Foot Adjustment 0˚ to 10.
64 Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label Lens Cover with string Serial Control Cable ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards.
65 Appendix T erminal: Mini DIN 8-PIN SERVICE PORT CONNECT OR COMPUTER IN/S-VIDEO IN/COMPONENT IN/MONITOR OUT TERMINAL (ANALOG) T erminal : Analog RGB (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Configurations of T erminals Red (R/Cr/S-C) Input/R Output Ground (Horiz.
66 Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service station. PIN Code Number Memo Factory default set No: 1 2 3 4* * Should the four-digit number be ch a n g e d , t h e f a c t o r y se t n u m b e r will be invalid.
67 Dimensions Appendix 3.74(95) 13.0 (330) 2.18(55.3) 9.33(237) 3.62(92) 3.94(100) 5.83(148) 4.72(120) 2.95(75) 5.31(135) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.
KM7BC ©2008 Eiki International, Inc. U.S .A. EIKI International, Inc. 30251 Esperanza Ranc ho Sant a Margarita CA 92688-21 32 U.S .A. T el : 80 0-242-3454 (949)-457-0200 Fax: 80 0-457-3454 (949)-457 -7878 E-Mail : usa@eiki.
Een belangrijk punt na aankoop van elk apparaat Eiki LC-XB21B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Eiki LC-XB21B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Eiki LC-XB21B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Eiki LC-XB21B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Eiki LC-XB21B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Eiki LC-XB21B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Eiki LC-XB21B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Eiki LC-XB21B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
