Gebruiksaanwijzing /service van het product ENRXWI-SG van de fabrikant ENCORE
Ga naar pagina of 25
108M 802.11g Wireless LAN Access Point User Guide.
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagne tic energy is emitted from Wireless LAN devices. The energy levels of these emission s however are far m uch less than the electromagnetic energy emissions from wi reless devices like for example mobile phones.
FCC Radio Frequency Exposure statement This Wireless LAN radio d evice has bee n evaluated under F CC Bulletin OET 65 and found compliant to t he requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b ) (4) addressing RF Exposure from radio fr equency devices.
Safety Information Your device contains a low power transmitter . When device is tr ansmitted it sends out radio frequency (RF) si gnal. CAUTION: To maintain co mpliance with FCC’s RF exposure guidelines, this equipment should be instal led and operated with mini mum distance 20cm between the radiator and your body.
TABLE OF CONTENT About This Guide ...................................................................................................... 1 Purpose ........................................................................................................
ABOUT THIS GUIDE Congratulations on your pu rchas e of this 108M Super-G Wireless LAN Access Point. This manual he lps to features the innovating wireless techno logy that can help you build a wireless network easily! T h is manual cont ains detailed instructi ons in operation of this pr oduct.
UNPACKING AND SETUP This chapter provide s unpacking and setup inform ation for the Access Point. Unpacking Open the box of the Access Point and carefu lly unpack it.
HARDWARE INSTALATION LED Indicator The figure below shows t he LED Indicator of t he Wireless LAN Access Point. Figure 1. Font panel Power This indicator lights green when the Access Point recei ves power.
Ethernet Ethernet uplink port with auto-sens ing fo r connecting to either 10/100Mbps Fast Ethernet connections, connect this port to switc h/hub. Reset To reset the setting back to factory default se.
Connect to the Switch/Hub 1. Plug in one end of the RJ45 networ k cable to the Switch/Hub port, 2. Plug in the other end of the RJ45 networ k cable to the Wirele ss Access Point. Check the installation The control LEDs of the Ac cess Point are clearly visibl e and the status of the network link can be seen instantly: 1.
CONFIGURING THE WIRELESS LAN ACCESS POINT The Wireless Access Point ha s a Web GUI inte rface for t he configuration. The AP can be configured through the Web B r owser. A network manager can manage, control and monitor the AP from the local LAN. This sectio n indicates how to configure the AP to enable its functions.
Quick Setup with Wizard Setup wizard is provided as the part of the web configurat ion utility. You can simply follow the step-by-step process to get your Access P oint configuration r eady to run in 4 eas y steps by clicking on t he “Wizard” button on the function menu.
Step2: Set WLAN Connection Please type the name of SSID you like and select the chann el. Then, click “Next” to continue. Figure 8. Setu p Wizard – Set Wireless LA N Connection Step 3: Set WEP Encryption If you like to enable WEP, please click “Enabled” .
Step 4: Restart The Setup wizard is now co mpleted. The new settings w ill be effect ive after the Access Point restarte d. Please click “Restart” to reboot the Access P oint. If you do not want to make any changes, please click “exit ” to quit without any changes.
Status The Status Function shows the System, Wireless Configuration and TCP/IP Configuration status and some settings of the Access P oint. Figure 12. Status Firmware Version: Shows the current firmwa re version. LAN: Shows the Mac address, IP address (default: 192.
View Log: Upon clicked, the page will change to log page . The log page records every event and the time that it happens. Figure 13. View Log You may clear the entries re cord ed in the log by clicking the “ Clear Log ” button, and refresh the screen to show the latest log entries by clicking the “ Refresh ” button.
AP Name: appoint a name for the AP. SSID: It is an ASCII string up to 32 ch aracters used t o identify a WLAN that prevents the unintentional merging of two co-lo cated WLANs. The SSID value must be th e same in all sta tions and AP in the extended WLAN.
IP Setting This page allows you to configure the IP and DHCP se ttings of the Access Point. Figure 16. IP Setting The default IP address of th is access point is 192.168.1.1 with the subnet mask of 255.255.255.0. You can type in othe r values for IP Address, Subnet Mask and Gateway and click “ Apply ” button for the changes to be effective.
Advanced Setting This page contains configurations for a dvanced users, which the change reflects, the wireless performanc e and operating modes. Figure 17. Advanced Setting AP Mode: Select one of the AP operating m odes for different application of Access Point.
Wireless Bridge mode – A pair of APs operating under Bridge mode to act as the bridge that connec t two Ethernet networks or E thernet enabled clients together. You must make sure that th e SSID and Channel is set th e same as that AP you wish to connect.
CTS Mode (clear to send): None- d isable CTS func tion. A lways- Regardless of wireless environment (11b or 11g), plat form will always tr ansfer 11g packet. Auto- AP soon detected th e wireless environment and decided the transmission packet, either 11b or 11g.
Security This page is where you confi gure the security features supported by this Access Point. Figure 18. Security Password: Allow you to change the new login password. Here are the necessary steps: 1. Enter the new password in the “ AP Password New: ” field.
Tools Four functions are provided in this page, Backu p, Restore Settings, Restore default settings and Firmware Upgrade. Figure 19. Tools Backup Settings: Click on “ Backup ” button, which will open a FileSave Dialog box, where you get to save all the current settings and configurations to a file.
TECHNICAL SPECIFICATIONS General Standards IEEE 802.11b Wireless LAN, IEEE 802.11g Wireless LAN IEEE 802.3u Fast Ethernet Signal Type: 802.11b: DSSS, 802.11g:OFDM Modulation: QPSK / BPSK / CCK / OFDM LED Indicators: Power, LAN (Link/Activity), WLAN (Activity) Frequency Range 2412 ~ 2484 MHz ISM band (channels 1 ~ 14) Frequency Band: 2.
Physical and Environmental DC inputs 5VDC /2A or higher current Temperatur e Operating: 0 ° ~ 40 ° C, Storage: -10 ° ~ 70 ° C Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90% Dimensions 146 x 113 .
Een belangrijk punt na aankoop van elk apparaat ENCORE ENRXWI-SG (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ENCORE ENRXWI-SG heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ENCORE ENRXWI-SG vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ENCORE ENRXWI-SG leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ENCORE ENRXWI-SG krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ENCORE ENRXWI-SG bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ENCORE ENRXWI-SG kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ENCORE ENRXWI-SG . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
