Gebruiksaanwijzing /service van het product 50-1386 van de fabrikant Enviro
Ga naar pagina of 23
PLEA SE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE SHERWOOD INDUSTRIES IS AN ENVIRONMENT ALL Y RESPONSIBLE COMP ANY . THIS MANUAL IS PRINTED ON RECYCLED P APER. 50-1386 PELLET STOVE Empr ess TECHNICAL MANU AL PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER.
T able of Contents 2 Introduction......................................................................................................... ...3 Rating Label Location.....................................................................................3 Important Safety Data.
3 Introduction * This manual is designed for the technician in conjunction with the owner’s manual. * R ATING L ABEL L OCATION : The rating label is located on the hopper top behind the surr ound panel. I MPORTANT S AFETY D ATA : Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet Stove.
4 Introduction ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 120 volts, 60 hertz electrical outlet and also must be accessible.
5 Inst alla tion R EMOVING P ELLET S TOVE F ROM P ALLET : Figure 1: Removing Stove From the Pallet. Use a flathead screwdriver or 5 / 16 ” socket to remove the four (4) screws that secure the Empress FPI to the pallet.
Inst alla tion 6 1 2 " ( 3 0 . 5 c m ) M a n t l e 36" (91cm) 3" (7.6cm) 24" (61cm) Fl o o r P r o t e c t i o n ; M i n 6 " ( 1 5 c m ) i n f r o n t o f d o o r Figure 4: Empress FPI Clearance to Combustibles.
Inst alla tion M ASONRY F IREPLACE I NSTALLATION : If installing the Empress with a skirt the skirt must be installed before the installation. A non-combustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater .
8 Inst alla tion P OSITIVE F LUE C ONNECTION WITHOUT A F ULL R ELINE (USA O NLY ): This unit does not require a f ull reline (in USA only) when installing into a masonry fireplace, however , it is recommended to ensure proper dr afting of the appliance.
I NSTALLATION OF C AST S KIRT O PTION : Figure 9: Assembling Cast Skirt. Inst alla tion A DJUSTING H OPPER H EIGHT : The back height of this unit can be set to one (1) of three (3) heights; 19 13 / 16 ” (503 mm), 20 13 / 16 ” (529 mm), 21 13 / 16 ” (554 mm).
1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the desired area. 2. Install a 12 or 24 V olt Thermostat using an 18 x 2 gauge wire from the unit to the thermostat.
11 Inst alla tion S LIDER /D AMPER S ETTING : This is used to regulate the airflow through the pellet stov e. THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper . More Air Less Air Figure 15: Slider / damper positions.
T roubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oil lubrication.
13 T roubleshooting ü Check the exhaust blower voltage across the blower wires (>=114V on #5 setting and >= 82V on #1 setting). – Replace the Circuit Board if the Voltage reading is less than 82V.
T roubleshooting Auger light flashes but auger motor does not turn at all. ü If the auger gear box does not turn but the motor ’ s armature does try to spin then the auger is jammed. – T ry to break apart jam by poking at the jam through the drop tube.
15 Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown Thermostat Selector Pins White White White 115V White 220V Blue White White Orange Orange Orange Orange Yellow Yellow Grey Grey Grey .
P ar ts List Reference Number Description Part Number 1 120 °F (49 °C) Ceramic F an T emperature Sensor EC -001 Domestic Power Cor d - 115V EC -042 2 Auger Motor - 115V EF-001 3 High Limit T emp Sen.
17 P ar ts List Reference Number Description Part Number 15 Exhaust Starter T ube 3” Quick Connect 50-1391 16 Mother Board - 120V 50-1392 17 Daughter Board - 120V 50-1393 18 Slider Damper & Leve.
P ar ts Diagr am - Components 3 Empress - Fireplace Insert Components October 2006 1 9 8 1 1 2 12 14 21 17 16 5 10 18.
19 P ar ts Diagr am - P ar ts 6 Empress - Fireplace Insert Parts October 2006 30 32 13 22 4 18 25 23 28 24 26 27 7 31 29 19 15 20.
20 W arr anty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do.
W arr anty Exclusions and Limitations: 1. This Warr anty does not co ver tarnish, discoloration or wear on the plating or paint. 2. This Warr anty ex cludes wear and tear or breakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace.
22 W arr anty 17 . Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces fr om the use of abrasiv e cleaners or polishes is not covered in this warr anty . 18. The Limited W arr anty does not cover tarnish, discolor ation or wear on the plated surfaces.
23 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE.
Een belangrijk punt na aankoop van elk apparaat Enviro 50-1386 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Enviro 50-1386 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Enviro 50-1386 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Enviro 50-1386 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Enviro 50-1386 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Enviro 50-1386 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Enviro 50-1386 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Enviro 50-1386 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
