Gebruiksaanwijzing /service van het product ENVIRO MAX 50-1531 van de fabrikant Enviro
Ga naar pagina of 16
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. Contact your building or fire officials about restrictions and installation inspection requirements in your area.
T able of Contents 2 Introduction........................................................................................3 Rating Label Location................................................................3 P ellet Quality .........................
3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * R ATING L ABEL L OCATION : The rating label is located on the inside of the hopper . P ELLET Q UALITY : Pellet quality is important, please read the following: Your Enviro pellet stove has been designed to burn ” (6mm) dia wood pellets only.
4 Safety W arnings & R ecommend a tions Please read this entire Owner’s Manual before installing or operating your Enviro Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death.
5 Safety W arnings & R ecommend a tions ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 110-120 volts (3.6 Amps), 60 hertz electrical outlet and also must be accessible.
21 13 / 16 " (554mm) 15 15 / 16 " (404mm) 21 9 / 16 " (548mm) 41 1 / 4 " (1047mm) 41 13 / 16 " (1063mm) 23 13 / 16 " (605mm) 25 5 / 8 " (650mm) 26 3 / 4 " (680mm) 25 1 / 16 " (637mm) Oper a ting Instructions D IMENSIONS & S PECIFICATIONS : Figure 1: Dimensions of Maxx.
7 Oper a ting Instructions C ONTROL B OARD F UNCTIONS : 1. AUGER TRIM: Used to change feed rates on LOW ONL Y for poorer quality fuels. Push the Auger T rim button until the number 1 and 5 lights appear on the Heat Lev el Indicator . This will increase the feed r ate to 4 seconds ON time Auger pulse.
Oper a ting Instructions O PERATING Y OUR P ELLET S TOVE : DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN. Keep hopper lid closed except during re-fuelling. CAUTION: When oper ating during adverse weather , such as high winds or freezing r ain, if the unit exhibits dr amatic changes in combustion stop using the unit immediately .
9 too much air – Close slider (push in) slightly . • If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame with no black tips then the air is set for proper operation, r efer to Figure 7 . The combustion exhaust blower is a variable speed blower controlled by the heat output button.
Check the Burn Pot Liner DAIL Y Weekly Bi-annually or 2 T ons of Fuel Burn Pot and Liner - Empty Exhaust V ent Heat Exchanger T ubes Fresh Air Intake T ube Ash Box Blower Mechanisms Door Glass Heat Ex.
11 R outine Cleaning and Maintenance DOOR GLASS CLEANING (W eekly) Cleaning of the glass must only be done when stove is cold. Open the door by lifting the handle. The glass can be cleaned by wiping down the outside and inside of the glass with a dry soft cloth.
R outine Cleaning and Maintenance EXHAUST VENT (Biannually) This v ent should be cleaned every year or after two tons of pellets. W e recommend contacting your dealer for professional cleaning. T o clean the v ent pipe, tap lightly on the pipe to dislodge any loose ash.
13 W arr anty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do.
W arr anty Exclusions and Limitations: 1. This W arr anty does not cov er tarnish, discoloration or wear on the plating or paint. 2. This W arr anty excludes wear and tear or br eakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace.
15 W arr anty 17 . Damage to plated surfaces caused b y fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces fr om the use of abrasiv e cleaners or polishes is not covered in this warr anty . 18. The Limited W arr anty does not cover tarnish, discolor ation or wear on the plated surfaces.
16 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE.
Een belangrijk punt na aankoop van elk apparaat Enviro ENVIRO MAX 50-1531 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Enviro ENVIRO MAX 50-1531 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Enviro ENVIRO MAX 50-1531 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Enviro ENVIRO MAX 50-1531 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Enviro ENVIRO MAX 50-1531 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Enviro ENVIRO MAX 50-1531 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Enviro ENVIRO MAX 50-1531 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Enviro ENVIRO MAX 50-1531 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
