Gebruiksaanwijzing /service van het product ES-1200C Pro van de fabrikant Epson
Ga naar pagina of 30
.
EPSON ® ES-1200C Pro PC Getting Started @ Tl& mumal is printed on 50% recycled paper, 10% post-consumer content..
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
Introduction This package contains all the hardware and software you need for professional quality color scanning. Here are the contents of your scanner package, described in the order you’ll need t.
System and Memory Requirements For the scanner hardware and software to work properly, your system must have at least the following configuration: ci cl cl ci Li P D cl cl A 386-based or higher PC or an IBM ® PS/2 ® machine MS-DOS ® 5.0 or higher Microsoft ® Windows 3.
Installing the Interface Card Use this procedure to install a SCSI interface card. For more detailed installation instructions, see the manual that came with your card. 1. Turn off the computer and any peripheral devices. 2. Disconnect the computer’s power cable from the electrical outlet and from the back panel.
10. Replace the cover and reconnect any cables you disconnected. Plug the power cord into an electrical outlet. Setting Up the Scanner Follow these steps to set up the scanner: 1. Take the scanner out of the box and place it on a flat, stable surface with its rear panel facing you.
4. Firmly connect the power cable to the power inlet on the rear of the scanner and the other end into an appropriately grounded outlet as shown below. If the scanner comes on when you plug it in, turn it off by pressing the OPERATE button. Warning: Whenever you turn off the scanner, wait at least 10 seconds before turning it back on.
Connecting the Scanner to the Computer Use this procedure to connect the scanner directly to the SCSI port on your computer using the cable included in the scanner package.
3. Switch on the internal SCSI terminator, as shown. 4. Set the SCSI ID switch to 2, as shown. 5. Turn on the scanner, then the computer. (Always turn on the scanner before the computer.
Installing EZ-SCSI Software If you are running Windows NT, you do not need to install EZ-SCSI software. Skip to the “Installing Adobe Photoshop” procedure. Follow these steps to install the Adaptec EZ-SCSI software: 1. Start Windows. 2. Insert the Adaptec EZ-SCSI Disk 1 in a diskette drive.
10. Remove the final installation disk from the drive and choose Continue. The installation program creates an Adaptec SCSI program group containing Adaptec icons. Installing the EPSON Scanning Utilities The EPSON Scanner Utility program includes EPSON Scan! II and EPSON TWAIN.
6. The next screen prompts you for the path name of the Windows directory. If the displayed path is where your Windows program resides, choose OK. 7. When the Scanner Setup dialog box opens, select SCSI as the interface type. The program supplies the port ID, as shown below.
9. Choose the Test button. If the scanner and EPSON Scanner Utility software are set up correctly, the scanner scans the image; after a few moments, the scanned image appears in the Scanner Setup dialog box, as shown below. Interface SCSI f 10. Choose OK to close the Scanner Setup dialog box.
Installing the ATM program Follow these steps to install Adobe Type Manager: 1. 2. 3. 4. 5. 6. Start Windows. Insert the ATM program disk into a diskette drive. From the Program Manager, open the File menu and choose Run. The Run dialog box appears. Type A:INSTALL (or B:INSTALL) in the Command Line text box and choose OK.
4. Type A:SETUP.EXE (or B:SETUP.EXE) in the Command Line text box and choose OK. The Adobe Photoshop Installer dialog box appears, as shown below. 51951: WJiJK 2841; 5441: 1500 K Space Required: 8412K Space Availabb: 833881: 5. Leave the Installation Options selected.
Selecting the Acquire Device Before you can scan an image from Photoshop, you need to select the scanner as the acquire device. Follow these steps: 1. From the Program Manager, open Photoshop by double-clicking on its icon in the Adobe program group. 2.
lnstalling Kai’s Power Tools Before you install Kai’s Power Tools, make sure that you have installed Adobe Photoshop. Then follow these steps: 1. Insert Disk 1 of Kai’s Power Tools into a diskette drive. 2. From the Program Manager, open the File menu and choose Run.
7. Remove the final installation disk from the drive. You can access Kai’s Power Tools filters from Adobe Photoshop by choosing KPT filters or KPT Extensions from the Filters menu in the Photoshop Menu Bar. For more information on Photoshop or the installation options, consult the Kai’s Power Tools for Windows Explorer‘s Guide.
3. Carefully close the document cover so that you do not disturb the position of the photograph on the glass. Choose Acquire in the File menu; then choose TWAIN.
5. In the scroll bar next to the Image Type button, select the image type appropriate for your scan. If you are scanning a color photograph, select Color Photo. 6. Click on the full-page Preview icon, , at the bottom of the dialog box. This does a fast preview scan so you can see the scan area.
When you have defined the portion of the image you want to scan, choose the Scan button. In a few moments, the scanned image is imported into the Photoshop window. To see the scanned image, close the EPSON TWAIN dialog box. Once you have your images and text, you can put them together in reports, newsletters, brochures, or business presentations.
Calibrating Your System Calibration allows you to match your scanner and your output device so that you can reproduce images that are very close to the original. Monitors use a different technology than printers, so images look different on the monitor than when they are printed.
2. Choose Screen Calibration from the Calibrate menu. You see the screen shown below: I I Adjust the slider below until the gray areas appear the same. I I I &, I I & 3. Look at the display from a distance and adjust the slide bar until the separate rows have the same basic color intensity.
Note: If you change your display monitor, you will need to create a new screen calibration profile. Do this by selecting Calibration Profile in the Configuration dialog box. The new screen calibration profile overrides the old one. Exporting a calibration chart Follow these steps to export a calibration chart from Scan! to your application: 1.
7. Open the file for the calibration chart file you exported. The chart contains nine blocks of color gradations surrounded by a black border on three sides and a gray border with some grayscale gradations on top. 8. Save the calibration chart file within Photoshop by selecting Save from the File menu.
5. In the File Name field, type the filename of the calibration file you want to create. Make sure you assign a CAL extension to this file. 6. In the Description field, type a short description of the printer you use to print the calibration chart. 7.
The scanner scans the image using information from the calibration profile to produce the best possible image for your printer. Selecting the Right Resolution Selecting the best resolution for scanning your image hinges on two factors: the final output device you plan to print the image on, and the acceptable file size.
Copyrighted Materials Like photocopiers, scanners can be misused by improper copying of copyrighted material. Although Section 107 of the U.S. Copyright Act of 1976 (Title 17, United States Code), the “fair use” doctrine, permits limited copying in certain circumstances, those circumstances may not be as broad as some people assume.
Epson America, Inc. 20770 Madrona Avenue Torrance, California 90503 CPD20838/94.
Een belangrijk punt na aankoop van elk apparaat Epson ES-1200C Pro (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Epson ES-1200C Pro heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Epson ES-1200C Pro vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Epson ES-1200C Pro leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Epson ES-1200C Pro krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Epson ES-1200C Pro bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Epson ES-1200C Pro kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Epson ES-1200C Pro . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
