Gebruiksaanwijzing /service van het product LX-86TM van de fabrikant Epson
Ga naar pagina of 146
EPSON ® LX-86 TM PRINTER User's Manual.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
Contents List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . vii List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introductio n ............................... . 1 LX-86 Features .................
5 IX-86 Features ..................... . Demonstration Programs ............. . Pica Printing. ...................... . Changing Pitches ................... . Cancelling Codes ................... . Resetting the Printer ................ . Pitch Comparison.
9 Introduction to Dot Graphics ................. . 71 Dot Patterns ............................... . 72 Print Head ................................ . 73 Graph&Mode ............................. . 73 Pin Labels ................................. . 74 First Graphics Program.
F Troubleshooting and Advanced Features ......... . Problem / Solution Summary .................. . Setting print styles ........................ . Tabbing ................................ . Graphics ................................ . Paper-out sensor .
List of Figures l-l Printer parts ............................... . l-2 Paper feed knob installation .................. . l-3 Ribbon cassette. ............................ . l-4 Print head assembly ......................... . l-5 Ribbon cassette installation .
E-l E-2 E-3 E-4 E-5 E-6 E-7 E-8 I-l 2-l 5-1 6-1 6-2 6-3 9-l D-l D-2 I-l I-2 Continuous paper with printer stand. ........... . Continuous paper without stand ............... . Tractor placement. .......................... . Paper separator and paper guide .
Introduction The Epson IX-86 printer combines low price with the high quality and advanced features formerly available only on more expensive printers.
About This Manual We’re not going to waste your time with unnecessary information, but we won’t neglect anything you need to know about the Ix-86 and its many features.
Chapter 1 Setting Up Your LX-86 Printer Setting up your LX-86 printer is a simple matter of attaching two parts, putting in the ribbon and paper, and connecting the printer to your computer. This chapter will have you printing a test pattern within fifteen to twenty minutes and doing more complicated work not long after.
In addition to the items in the box, you need a cable and possibly an interface board. The cable connects the printer to your computer, and the interface board is necessary only for those computers that can’t use the LX-86’s Centronics ® paralle1 interface.
Figure 1-2. Paper feed knob installation Ribbon Installation The LX-86 printer uses a continuous-loop, inked fabric ribbon, which is enclosed in a cassette that makes ribbon installation and replacement a clean and easy job. The parts of this cassette are labelled in Figure l-3.
To install the ribbon, first open the lid at the front of the LX-86 so that you can see the print head assembly shown in Figure l-4. Move the assembly by hand to the center of the printer so that the other parts of the printer will not get in your way.
Then hold the ribbon cassette so that the small knob is on top and the exposed section of ribbon is away from you. Insert the cassette in its holder by first sliding the pins at the back of the ribbon cassette under the small hooks on the holder. (See Figure l-5.
Now turn the knob on the cassette in the direction of the arrow to tighten the ribbon. As you turn the knob, see that the ribbon slips down into its proper place between the print head nose and the silver ribbon guide (Figure l-6). If it doesn’t, guide it with a pen or a pencil.
Paper Loading Now put a sheet of paper in your LX-86 so you can test it. Figure l-7 shows the names of the parts that you need to know. Friction lever Figure l-7.
See that the printer is turned off, open the front lid, and push the friction lever back and the paper bail forward. Then move the print head by hand to the center of the printer and feed the paper into the paper slot in the top of the printer.
There are three buttons and four indicator lights on the control panel. Lights l The POWER light glows green when the power is on. l The READY light glows green when the printer is ready to accept data.
Test Pattern Now you’ll see your Lx-86 print something even though it’s not connected to a computer yet. Make sure that your printer has paper in it and that the power switch is off. Now, hold down the LINE FEED button on the control panel while you turn the printer on with the power switch.
Connecting the LX-86 to Your Computer Now that the test pattern has shown that your printer is working well, it’s time to hook it up to your computer. It is best to have both the printer and the computer turned off when you do this. Remember that each computer system has its own way of com- municating with a printer.
Next connect the other end of the printer cable to your computer. On most computers you can easily find the correct connector for the printer cable, but if you are not sure, consult your computer manual or your dealer. First Printing Exercise Now it is time to see something more interesting than the test pattern from your LX-86 printer.
Chapter 2 SelecType The LX-86’s SelecType feature can produce four special typestyles: This is emphasized printing. This i s in the double-strike mode . This is condensed printing. This is in the elite mode. SelecType Operation Using SelecType is easy.
Note: If the printer beeps twice before you release the buttons, you have pressed the FORM FEED button before the OFF LINE button instead of at the same time and the LX-86 is in the NLQ mode. Press the OFF LINE button to put the printer back on line and press the DRAFT button if you do not want NLQ.
After turning on SelecType, follow these three steps to select a typestyle: 1. Find the typestyle you want in Table 2-1. Table 2-l. SelecType modes Mode Typestyle or Function 1 Emphasized ABCDEFGHIJKLMnopqrstuvwxyz 2 Double&trike ABCDEFGHIJKLMnopqrstuvwxyz 3 condensed ABCDEFGHIJKLMnopqrstuvwxyz 4 Elite ABCDEFGHIJKLMnopqrstuvwxyz 2.
Now, run the program by typing RUN and pressing RETURN, or print your file or document by following the printing instructions of your software. The LX-86 will print your example in standard single- strike printing, as shown below: This is an exampl e of LX printing .
SelecType Tips Once you have learned the simple technique for controlling print styles with SelecType, you can use it whenever you wish. You should be aware of a few restrictions, however. l SelecType is designed to control the printing of an entire file or document, not an individual line or word.
Chapter 3 Elements of Dot Matrix Printing This chapter is for those of you who want to know something about how your printer works. It’s a simple, non-technical explana- tion of the basics of dot matrix printing that will help you understand some of the later chapters.
Bidirectional Printing In nearly all of our discussions in this manual, we describe the action of the LX-86 print head as moving from left to right, as a typewriter does. During its normal operation while printing in the draft mode, however, the LX-86 prints bidirectionally.
.
In Figure 3-3 there is a grid of lines behind the pica characters so that you can more easily see how they are designed. As you look at these characters you can see three rules that govern their desig.
The panel buttons make it especially easy to change from draft to NLQ, but you can also select and cancel the NLQ mode with a software command which you can find in Chapter 5.
Chapter 4 Printer Control Codes The LX-86 printer is easy to use, especially with commercial soft- ware that has print control features. This chapter explains some of the basics of printer control and communications to help you understand how a computer communicates with your printer.
Computer and printer interaction would be terribly confusing if different kinds of computers and printers used different numbers for the same letter of the alphabet. Therefore, most manufacturers of computers, printers, and software use the American Standard Code for Information Interchange, usually referred to as ASCII (pro- nounced ASK-Key).
Printer Codes To take advantage of the many print features of the IX-86, you can use a software program that sends the correct codes or you can use another method to send codes.
l The ESCape and control keys on your computer’s keyboard. With this system you send the ESCape code by pressing the ESCape key and a carriage return by pressing the control key and the M at the same time. (See Appendix B or the Quick Reference Card for the control key codes.
If your word processing program allows inserted codes, it will probably do standard printing without such codes. It is only for special features that you will need to use inserted codes. For example, if you want to have headings in wide bold printing (called double-width emphasized), you would probably have to use inserted codes.
Chapter 5 IX-86 Features Beginning with this chapter we describe many of the printing fea- tures of the LX-86. Although we include programs that demonstrate these features, you don’t have to be a programmer to learn about the features from these chapters.
If you don’t want to do the exercises in BASIC, you don’t have to. Many users are quite happy with their printers without ever learning any more about them than how to turn them on and off and how to load paper. Therefore, you shouldn’t be intimidated by the informa- tion in this manual.
Now run the program. You should get the results you see below, 10 pica characters per inch. ABCDEFGHIJKLMNOPQTRSTUVWXYZ[]ˆ_`abcdefgh i Changing Pitches Now you can try other pitches.
To avoid having one program interfere with the printing modes of another, you can cancel a mode one of two ways: l With a specific cancelling code, such as the ESCape “P” that we used above to cancel elite. Each mode has a cancelling code, which you can find in the discussion of the code and in Appendix B.
In fact, if you need even more than the 132 characters per line that condensed gives you, you can combine elite and condensed for a mode we call condensed elite. It is not really another pitch, because the size of the characters is the same as in the condensed mode; only the space between the characters is reduced.
All the modes demonstrated in this chapter are compared in Table 5-l. Table 5-1, Summary of LX-86 pitches Print sample CPI Codes on oft 1 inch Near Letter Qualit y 10.0 0 ESC "x" 1 ESC "x" 0 Pica prin t 10.00 ESC "P" ESC "M" Elite prin t 12.
Chapter 6 Print Enhancements and Special Characters Now that you have seen how you can change the pitch of your IX-86 printing, we can show you many more ways to vary and enhance your printing. So that you won’t have to type in dozens of programs to try all the features, we give you just one master program that can demonstrate any feature.
Emphasized works only in draft pica and NLQ modes. In elite and condensed the dots are already so close together that even with the reduced print speed, the LX-86 cannot fire, retract, and again fire the pins quickly enough to print overlapping dots.
You should get the following printout when you run this program and type “E” and “emphasized” in answer to the questions. This sample U ses ESCape E to produce emphasized printing . The code to turn off emphasized is ESCape “F”. Double-strike The other bold mode on the LX-86 is double-strike.
Double-width Mode Perhaps the most dramatic mode on the LX-86 is double-width. It produces extra-wide characters that are good for titles and headings. For this mode, the dot pattern of each character is expanded and a duplicate set of dots is printed one dot to the right.
Mode Combinations You can combine nearly all of the print modes on the LX-86. Indeed, your Ix-86 printer can print such complicated combina- tions as double-strike emphasized double-width underlined italic subscript, although we’re not sure that you would ever want to use such a combination.
Standard Pica Prin t Italic Pica Prin t Figure 6-4. Italic and pica The code to turn italic mode on is ESCape “4”. Try it in the master program if you wish. When you use this code in the master program, enter “4” in answer to the first question just as if it were a letter of the alphabet instead of a number.
This uses the underline mode. Figure 6-5. The underline mode As shown in Figure 6-5, the underline mode is continuous, but some word processing and other applications programs produce an underline that leaves spaces between characters as demonstrated in the printout below.
For any combination,. just add up the values of each of the modes you want and use the total as the number after ESCape “!“. For example, to calculate the code for double-width italic underlined p.
Indeed, Master Select is such a powerful feature that it may occa- sionally be more powerful than you want it to be. Because it controls eight different modes, a Master Select code will cancel any of those eight that are not selected. For example, suppose that you have a page in elite and want part of it printing in italic.
If n is 1, the command turns the Character Graphics set on; if n is 0, the command turns that set off. If you prefer to have the Character Graphics set on most of the time, see Appendix D for instructions on using the DIP switches. The Character Graphics set is actually two sets, the standard and the international.
You select the character set in one of two ways: with an ESCape code or with a switch in the back of your printer. The ESCape code in BASIC has the following format: LPRINT CHR$(27)“R”CHR$(n ) in which n stands for the appropriate number from the list above.
Table 6-3. International characters in draft italic 3 5 36 6 4 91 9 2 93 9 4 9 6 123 12 4 125 126 USA FRANC E GERMAN Y U K DENMAR K SWEDE N ITAL Y SPAI N JAPAN NORWA Y DENMARK II The number at the top of each column in the tables is the ASCII code that prints the characters in that column.
Graphics character set The Lx-86 printer’s Read Only Memory (ROM) also contains the 32 graphics characters that you see in Figure 6-6. Figure 6-6. Special graphics characters Undoubtedly you can thi.
The next printout shows the characters in emphasized double- width pica: Because normal line spacing leaves space between the lines of graphics characters just as it does between lines of text, you must change the line spacing when you combine line graphics characters to form boxes or other figures.
Chapter 7 Page Formatting Although the LX-86 printer has many sophisticated commands to set margins, line spacing, and horizontal and vertical tabs, we won’t take up your time with extensive discussions of these because most of these functions are taken care of by applications programs.
You should be aware that a few applications programs reset the printer before each document or file they print. These programs will, of course, cancel your new margin settings.
Skip Over Perforation If you are using continuous pin-feed paper for printing program listings or other material not controlled by an applications program, you may find that the LX-86 prints right over the perforations be- tween pages. The LX-86 has an ESCape code to prevent this: the ESCape “N” command.
l/6 inch 1/6 inch 3 blank rows 3 blank rows Figure 7-l. Standard line spacing The default line spacing illustrated in Figure 7-l is the only one you need for almost all printing of text, but in some cases you may want to increase or decrease the space between lines.
Paper-Out Sensor Under the platen (the black roller) of your LX-86 printer is a small switch that senses whether or not paper is in the printer. When the end of the paper passes this switch, it sends a signal that sounds the beeper and stops your printing.
Chapter 8 User-Defined Characters The LX-86 has several hundred different characters stored in its ROM (Read Only Memory). Although this number includes draft, italic, international, character graphics, special graphics, and Near Letter Quality characters, sometimes you would like to have a few more.
After you have created your own characters with our programs, certain keys that you seldom use will generate the user-defined char- acters. For example, you will be able to type < to print . Your user-defined characters can be utilitarian or imaginative, any- thing from a scientific symbol to script letters for your initials.
When you place your dots on this grid, remember that dots cannot go on horizontal lines, but they can go on vertical lines so long as they do not overlap any other dots. As you design your characters, draw the dots as large as you see them in the example on the left in Figure 8-2.
So that you can see how the program works, we’ll present the steps used to create the symbol for Mercury. First is the grid we used to design the character. 8 7 6 5 4 3 2 1 123456789 Figure 8-3. Design for character Running the program Now run the program.
Now wait a moment for your computer to calculate the dot pat- terns and your LX-86 to print the new character in two different typestyles. Your printout also gives you nine numbers, which you will use in the next program.
90 FOR P=58 TO 63: LPRINT CHR$(P);" ";: NEXT P 95 LPRINT 100 K=l: IF K>3 THEN A=58 ELSE A=60 110 LPRINT CHR$(27)": "CHR$(O)CHR$(O)CHR$(O); 120 LPRINT CHR$(27)"%"CHR$(l.
The two lines when printed by your own program provide you with a key to the characters your LX-86 will now print. When you press the key for one of the characters in the top row, the printer will print the corresponding character in the bottom row.
128 54 32 16 8 4 2 1 128 64 32 16 8 4 2 1 128 64 1 2 3 4 5 6 7 8 9 10 11 1 2 Figure 8-5. Grid for NLQ characters On this grid you can use any numbered line or space. As you can see, that includes the bottom line and the line on the right side. You should remember to leave one or two columns blank for space be- tween characters, however.
First data number Second data number Third data number 128 8 4 32 18 8 4 2 1 128 6 4 32 16 8 4 2 1 128 6 4 128 64 32 =229 4 1 16 8 =28 4 64 } =64 Figure 8-6. Data numbers for one column To calculate the data numbers for this column, you see which dots are used in the top group (the top eight positions) and add their values together.
128 64 32 16 8 4 2 1 128 64 32 16 8 4 2 1 128 64 8 32 255 32 8 0 0 0 255 0 0 0 0 0 192 0 0 0 I If you look at each column individually, you can see how the data numbers were calculated. First NLQ definition program Now type in and run the following program.
10 LPRINT CHRS(27);"xl"; 20 LPRINT CHR$(27);":" ;CHR$(O);CHR$(O);CHR$(O); 30 LPRINT CHR$(27);"%";CHR$(l);CHR$(O); 40 LPRINT CHR$(27);"&";CHR$(O);"<&.
When you run this program it prints six characters, then redefines one or more of them and prints them again. As with the draft charac- ters, you use this two-line printout as a guide to the new characters your IX-86 will print. You can use them with an applications prog- ram or a program you write yourself.
Chapter 9 Introduction to Dot Graphics The Epson dot graphics mode allows your LX-86 printer to pro- duce pictures, graphs, charts, or almost any other illustrative or crea- tive material you can devise.
Bookstore Inventory MAGAZINES BEST-SELLERS SCIENCE FICTION ---- - ROMANCE NON-FICTION CLASSICS MYSTERIES WESTERNS If you have a program that produces graphics, all you need to know about Epson dot graphics is how to use the software.
Print Head The graphics mode on the LX-86 is quite different from the text modes. Instead of sending codes for letters and printing functions, you send codes for dot patterns, one number for each column in a line. Since none of the predefined characters or symbols in the prin- ter’s memory is used, your program controls where each dot is printed.
The LX-86 has several different graphics densities, but we’ll keep things simple by using only one in the first exercises. The code for entering single-density graphics mode is ESCape “K” n l n 2 .
128 64 32 16 8 4 2 1 not used Figure 9-1. Pin labels To fire any one pin, you send its number. To fire more than one pin at the same time, add up the numbers of the pins and send the sum to the printer. With these labels for the pins, you fire the top pin by sending 128.
With this numbering system any combination of the eight pins adds up to a unique decimal number between 0 and 255. Although you use a decimal number, it is, of course, converted to a binary number before it goes to the printer.
30 LPRINT CHR$(27)"K"CHR$(100)CHR$(O); 40 FOR X=1 TO 50: LPRINT CHR$(85)CHR$(42); 50 NEXT X If you run the program now, you’ll see how one line of the pattern looks: To see a how more than one line combines to form a figure, enter and run the following program, which uses two of the lines you have already typed and adds several more.
Line 20 begins a loop to produce multiple print lines. Lines 30 and 40 were covered above, but an LPRINT is added to line 50 to pro- duce a line feed after line 40. Lines 60 and 70 are like lines 30 and 40 except that lint! 70 uses a reversal of the patterns in line 40.
You are familiar with the command format that uses the ESCape code and a letter, but LX-86 graphics commands can also be in the following format: LPRINT CHR$(27)“*“CHR$(M)CHR$(N1)CHR$(N2) ; with m being the mode number found in the left column of Table 9-1.
the maximum number of dots you can reserve on the IX86, then, is: CHR$(27)"Z"CHR$(128)CHR$(7) ; or, in the other format: CHR$(27)"*"CHR$(3)CHR$(l28)CHR$(7) ; which is 128 dots plus 7 times 256 dots, for a total of 1920 dots in one row.
Design Your Own Graphics In this section we take you through the development of a graphics program. The example is not especially complicated, but it does in- clude the same steps you would use for a more complex figure so that you have the basis for designing graphics on your LX-86.
Figure 9-4. Arrow design After plotting all the dots as in Figure 9-4, you calculate the num- bers for each pin pattern by dividing the design grid into separate print lines. For the arrow design the grid was divided into three lines, each seven dots high.
The numbers for the second and third lines were calculated in the same manner. Once the numbers for the pin patterns are calculated, they go in DATA statements, separated by commas.
Graphics Programming Tips Now that we’ve shown you how to design your own graphics, we’ll review and emphasize a few elements of graphics programming.
What went wrong? To help you understand the graphics command and avoid some of the more common errors made with it, we’ll examine this program in detail. First look at line 20. ESCape “K” calls for single-density graphics, and the two CHR$ numbers specify 50 columns of dots.
You may also wonder why the program prints not only the differ- ent pin patterns but also the character “J” a number of times. The reason lies in the number of columns you reserved with the graphics command.
10 G$=-CHR$( 27) + ”K” + CHR$( 100) + CHR(0) 2 0 A$=CHR$(85)+CHR$(42 ) 3 0 B$=CHR$(42)+CHR$(85 ) 40 LPRINT CHR$( 27 ”1” ; 5 0 FOR R=l TO 3 6 0 LPRINT G$; 70 FOR X=1 TO 50: LPRINT A$;: NEXT X 8.
Appendix A IX-86 Characters This appendix gives the control codes and characters for each code from 0 through 255 decimal (00 through FF hex). Page A-3 shows the characters in the Epson Character Graphics set. Further information on the character sets is in Chapter 6.
Dec Hex CHR Dec Hex CHR Dec Hex CHR Dec Hex CHR 0 00 none 1 01 none 2 02 none 3 03 none 64 40 @ 65 41 A 66 42 B 67 43 C 68 44 D 69 45 E 70 46 F 71 47 G 72 48 H 73 49 I 74 4A J 75 4B K 76 4C L 77 4D M .
Epson Character Graphics Standard International Dec Hex CHR 128 80 none 129 81 none 130 82 none 131 83 none 132 84 none 133 85 none 134 86 none 135 87 BEL 136 88 BS 137 89 HT 138 8A LF 139 8B VT 140 8.
Appendix B Commands in Numerical Order This appendix lists all the LX-86 commands in numerical order. The page number column indicates where a complete description can be found. Note that for commands from ESC SO onwards, the decimal and hexadecimal columns show only the second code; the first code for those commands is the ESCape code.
ASCII Dec Hex Description Page ref BEL 7 07 BS 8 08 HT 9 09 LF 10 0A VT 11 0B FF 12 0C CR 13 0D s o 14 0E SI 15 OF DC1 17 11 DC2 18 12 DC3 19 13 DC4 20 14 CAN 24 18 DEL 127 7F ESC SO 14 0E ESC SI 15 0.
ASCII Dec Hex Description Page ref ESC G ESC H ESC J ESC K ESC L ESC M ESC N ESC O ESC P ESC Q ESC R ESC SO ESC Sl ESC T ESC U ESC W ESC Y ESC Z ESC / ESC a ESC b ESC e ESC f ESC 1 ESC m ESC s ESC t E.
Control Key Chart Some applications programs can use control key codes for decimal values O-27. The table below gives you the proper values. The Con- trol key column indicates that you press the control key at the same time you press the key for the letter or symbol in that column.
Appendix C Command Summary This appendix lists and describes all the commands available on the LX-86. This summary is divided into the following topics: Near Letter Quality Forms Control Character Wid.
ESC a Select Justification Mode Format: ASCII code: ESC Decimal: 27 97 (n ) Hexadecimal: 1B 61 (n) Explanation: See Chapter 7 for information on this command. Character Width SI Format: ASCII code: SI Decimal: 15 Hexadecimal: O F Select Condensed Mode Explanation: This command is only effective in draft mode.
so Format: ASCII code: s o Decimal: 14 Hexadecimal: O E Select Double-width (one line) Explanation: Double-width mode doubles the width of all characters, including spaces. It is cancelled by a carriage return or DC4. ESC SO Format: ASCII code: ESC S O Decimal: 27 14 Hexadecimal: 1B 0E Select Double-width Explanation: Duplicates the SO command.
ESC M Select Elite Pitch Format: ASCII code: ESC M Decimal: 2 7 77 Hexadecimal: 1B 4D Explanation: Selects elite pitch (12 characters per inch). ESC P Select Pica Pitch Format: ASCII code: ESC P Decimal: 27 80 Hexadecimal: 1B 50 Explanation: Selects pica pitch (10 characters per inch).
ESC G Format: ASCII code: ESC G Decimal: 27 71 Hexadecimal: 1B 47 Select Double-Strike Mode Explanation: Makes text bolder by printing each line twice, with the second printing slightly below the first.
ESC - Select Underlining Format: ASCII code: ESC -- (n) Decimal: 27 45 (n) Hexadecimal: 1B 2D (n) Explanation: When the value of n = 1, underlining is turned on, when n = 0, underlining is turned off.
ESC ! Master Select Format: ASCII code: ESC ! (n) Decimal: 27 33 (n ) Hexadecimal: 1B 21 (n) Explanation: This command enables a number of commands to be added together.
ESCR Select International Character Set Format: ASCII code: ESC R (n) Decimal : 27 82 (n) Hexadecimal: 1B 52 (n) Explanation: Some character codes produce different characters for different countries. The characters are outlined in Chapter 6. The value of n determines which character set is printed.
ESC 6 Select International Character Graphics Format: ASCII code: ESC 6 Decimal: 27 54 Hexadecimal: 1B 36 Explanation: When the character graphics set is selected, this code selects the international set.
ESC EM Automatic Sheet Feeder Control Format: ASCII code: ESC EM (n) Decimal: 27 25 (n ) Hexadecimal: 1B 19 (n) Control: Ctrl[ Ctrl Y (n) Explanation: This command is used with the optional automatic-sheet feeder. When n= 0 the feeder is turned off, when n = 4 it is turned on.
ESC s Select Half Speed Mode Format: ASCII code: ESC s (n) Decimal: 27 115 (n) Hexadecimal: 1 B 73 (n) Explanation: Selects half speed printing if n= 1 or returns to full speed if n=0.
ESC 1 Select 7/72 Inch Line Spacing Format: ASCII code: ESC 1 Decimal: 27 49 Hexadecimal: 1B 31 Explanation: Selects the line spacing to 7/72 of an inch for subsequent line feed commands.
ESC J Perform n/216 Inch Line Feed for One Line Format: ASCII code: ESC J (n ) Decimal: 27 74 (n ) Hexadecimal: 1B 4A (n) Explanation: Advances the paper by one line at a spacing of n/216 of an inch. The value of n should be in the range 0 to 255. This command does not send a carriage return with the line feed.
ESC 8 Format: ASCII code: ESC 8 Decimal: 27 56 Hexadecimal: 1B 38 Disable Paper-Out Sensor Explanation: Turns off the paper sensor so that you can print right to the end of a single sheet of paper. This command temporarily dupli- cates the function of DIP switch l-5.
ESC CO Set Page Length in Inches Format: ASCII code: ESC C NUL (n) Decimal: 27 67 0 (n) Hexadecimal: 1B 43 00 (n) Explanation: Sets the page length to n inches where n has a value of 1 to 22.
Page Format ESC B Set Vertical Tabs Format: ASCII code: ESC B Decimal: 27 (n1) (n2) . . . NUL 66 (n1) (n2) . . . 0 Hexadecimal: 1B 42 (n1) (n2 ) . . . 00 Explanation: This command allows setting of up to 16 vertical tabs. The tabs can be set in 8 channels using the ESC b command.
ESC / Select Vertical Tab Channel Format: ASCII code: ESC / (c) Decimal: 27 47 (c) Hexadecimal: 13 2F (c) Explanation: This command is used to set the vertical tab channel, where c has the value 0 to 7.
ESC D Set Horizontal Tabs Format: ASCII code: ESC D (n1) (n2) . . . NUL Decimal: 27 66 (n1) (n2) . . . 0 Hexadecimal: 1B 44 (n1) (n2 ) . . . 00 Explanation: This command allows setting of up to 32 horizontal tabs. These are entered as nl, n2, n3, etc.
ESC Q Format: ASCII code: ESC Q (n) Decimal: 27 81 (n) Hexadecimal: 1B 51 (n) Explanation: Set Right Margin This command sets the right margin to n columns in the current pitch. This command clears previous tab settings and all previ- ous characters in the print line.
ESC & Define User-Defined Characters Format: ASCII code: ESC & NUL (data1) (data2) . . . (data n) Decimal: 2 7 3 8 0 (data1) (data2) . . . (data n) Hexadecimal: 1B 26 00 (data1) (data2) . . . (data n) Explanation: This command allows characters to be re-defined in the cur- rently selected mode.
ESC L Select Double Density Graphics Mode Format: ASCII code: ESC L (n1) (n2) (data1) (data2) . . . (data(d)) Decimal: 27 76 (n1) (n2) (data1) (data2) . . . (data(d)) Hexadecimal: 1B 4C (n1) (n2) (data1) (data2) . . . (data(d)) Explanation: Turns on Low-Speed Double Density Graphics Mode, printing 960 dots per 8-inch line.
ESC Z Select Quadruple Density Graphics Mode Format: ASCII code: ESC Z (n1) (n2) (data1) (data2) . . . (data(d)) Decimal: 27 90 (n1) (n2) (data1) (data2) . . . (data(d)) Hexadecimal: 1B 5A (n1) (n2) (data1) (data2) . . . (data(d)) Explanation: Turns on Quadruple Density Graphics Mode, printing’ 1920 dots per 8-inch line.
ESC ? Format: ASCII code: ESC ? Decimal: 27 63 Hexadecimal: 1B 3F Explanation: Reassign Graphics Mode (s) (n) (s) (n) (s) (n) Change one graphics mode to another. The mode s is the ASCII code for the character K, L, Y, or Z which is reassigned to a mode O-6 as in the ESC * command.
BEL Format: ASCII code: BEL Decimal: 7 Hexadecimal: 7 Explanation: Sounds the beeper. Beeper DEL Format: ASCII code: DEL Decimal: 127 Hexadecimal: 7 F Delete Explanation: Removes the previous text character on the print line but does not affect control codes.
Appendix D The DIP Switches Several tiny switches called DIP (for Dual In-Line Package) switches are in the back of your LX-86 printer. They control a num- ber of important printer functions. For most uses they can be left as they were set at the factory, but you may want to change some settings.
Always turn the power OFF (with the switch on the right side of the printer) before you change the setting of any of these switches. Any changes made while the power is on will be ignored until you turn the printer off and back on. So set all switches with the power off.
Switch l-5 controls the paper-end detector. When it is ON, the detector is inactive, causing printing to continue even when the print- er is out of paper. When it is OFF, the printer stops when the end of the paper passes the paper-end detector. Some computer systems ignore the setting of this switch.
Appendix E Using the Optional Tractor Unit The optional tractor unit for the LX-86 allows you to use continuous paper with pin feed holes along the sides. The unit is adjustable so that the continuous paper can be any width from 4 to 10 inches. (The LX-86 can also use the LX-80™ tractor unit.
Figure E-2. Continuous paper without stand Tractor Unit Installation To install the removable tractor unit, first pull the friction lever toward the front of the printer. Then hold the tractor with the gears to the right as shown in Figure E-3. Figure E-3.
In each tractor slot are two pegs that fit into the notches on the tractor fittings. Tilt the tractor back so that the rear notches fit over the rear pegs. Then tilt the unit forward until it clicks into place. That’s all there is to it. Now install the paper separator and pull out the paper guide as shown in Figure E-4.
When you want to use single sheet paper in your LX-86, you can remove the tractor unit quite easily. Just push back the two tractor release levers shown in Figure E-5, tilt the unit backwards, and lift it up. Figure E-5. Tractor release levers Loading Continuous Paper Once your tractor is installed, you can load continuous paper.
Figure E-6. Pin feed bolder adjustment Next, open the pin feed covers as shown in Figure E-7 and feed the paper under the paper separator and into the paper slot; push the paper through until it comes up between the ribbon guide and the platen. Figure E-7.
Next pull the paper up until the top is above the pin-feed holders. Fit the holes on the left side of the paper over the pins in the left holder and close the cover. Now fit the right side of the paper in the right holder, moving the holder as needed to match the width of the paper.
Appendix F Troubleshooting and Advanced Features This appendix approaches troubleshooting from several directions. The first section uses a columnar format to match solutions with problems.
affect your system if possible. You can also POKE the problem codes directly to the printer port. Seven- bit computers cannot use the eighth pin (12 8). If you have a seven-bit computer and any of your graphics dat a numbers are larger than 127, change the design so that all numbers are less than 128.
Paper-out sensor Can’t deactivate paper-out sensor Computer systems that monitor with DIP switch l-5 or ESCape printer cable pin 12 will ignore "8". both ESCape “8” and the setting of switch l-5. These systems will stop the printing when no paper is in contact with the paper-end detector (a small switch located beneath the platen).
The hexadecimal numbers are the codes received by the printer, and the guide section helps you find a certain place in the list of codes. Each character in the guide section corresponds to one of the codes. If the code is for a printable character, that character is printed.
A hex printout of a program shows you exactly what the printer is receiving, regardless of what the computer is sending. The following test program lets you check to see what codes, if any, are problems for your computer system. 10 FOR X=0 TO 255 20 LPRINT CHR$(X) ; 30 NEXT X Put the printer in data dump mode and then RUN the program.
The second approach is to use commercially available software that is specifically designed to overcome these coding problems. Consult your computer dealer or computer publications to see if a program for your computer system is available. The third approach consists of avoiding the software that is chang- ing the codes.
The printer interface card furnished with the Apple II computer only passes seven bits to the LX-86, which means that you have a 7-bit system. Should you need an 8-bit system, the simplest solution is to purchase a new printer interface card from your computer dealer.
he 255 is a special number that prevents the computer system from inserting a CR-LF into the line. Unless, of course, there’s one in your program. The extra line feed-CHR$(10)--that accompanies each carriage return--CHR$(13)-- is no problem except when you need to use CHR$(13) in a graphics program.
Appendix H Technical Specifications Printing Printing method . . . . . . . . . . . . . . . . Impact dot matrix Printing speed . . . . . . . . . . . . . . . . . . . 120 characters per second in draft pica Paper feed speed . . . . . . . . . . . . . . . .
Characters per line: Maximum characters per line Pica 80 Pica double-width 40 Elite 96 Elite double-width 48 Condensed 132* Condensed double-width 66* Condensed elite 160 *137 if right margin is changed. *68 if right margin is changed. Paper Paper width Paper feed Pin-feed .
Environment Temperature . . . . . . . . . . . . . . . . . . . . . O p erating 41°F to 95°F (5°C to 35°C) Storage -- 22°F to 149°F (-30°C to 65°C) Humidit y . . . . . . . . . . . . . . . . . . . . . . . . . . Operating 10% to 80% (no condensa- tion) Storage 5% to 85% (no condensation) Shock .
INDEX For information on specific commands, see Appendix B or Appendix C. A American Standard Code for Information Interchange. See ASCII Apple computers, F6 - F7 ASCII (American Standard Code for Information Interchange), 27 - 28 codes listed for all characters, A-l -A-4 Automatic test.
E Elite mode, 35 Emphasized mode, 39 - 40 Environment, specifications for, H-3 Error, F3 ESCape code, 28 listed by function, C-l -C-24 listed by number, B-l -B-4 F FF. See Form feed Foreign language characters. See International characters FORM FEED button, 10 -- 11 Formatting, page, 53 -- 57 Friction lever, 9 -- 10, E-2 Function switches.
M Maintenance, G-l Margins, 53 -- 54 Master Select, 45 -- 47 Matrix. See Dot matrix N Near Letter Quality (NLQ) mode, 24 -- 25, 37 0 ON LINE light and button, 10 -- 11 See also SelecType P Page formatting, 53 -- 57 Panel buttons, selecting typestyles with.
U Underline mode, 44 -- 45 User-defined characters, 59 -- 70 W WIDTH statements, 80 Zero, slashed, D-2 -D-3 z J-4.
Een belangrijk punt na aankoop van elk apparaat Epson LX-86TM (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Epson LX-86TM heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Epson LX-86TM vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Epson LX-86TM leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Epson LX-86TM krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Epson LX-86TM bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Epson LX-86TM kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Epson LX-86TM . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
