Gebruiksaanwijzing /service van het product Z10000UNL van de fabrikant Epson
Ga naar pagina of 288
PowerLite ® Pro Z9870NL/Z11005NL/Z9800WNL/ Z9900WNL/Z11000WNL/Z9750UNL/ Z9870UNL/Z10000UNL/Z10005UNL User's Guide.
.
Contents PowerLite Pro Z9870NL/Z11005NL/Z9800WNL/Z9900WNL/ Z11000WNL/Z9750UNL/Z9870UNL/Z10000UNL/Z10005UNL User's Guide ........................................... 11 Introduction to Your Projector ................................................
Connecting to a Component-to-BNC Video Source .................................................................. 42 Connecting to a Component-to-VGA Video Source .................................................................. 43 Connecting to an S-Video Video Source .
Using Basic Projector Features ............................................................................................................... 79 Turning On the Projector ................................................................................
Adjusting Projector Features ................................................................................................................. 116 Shutting Off the Picture Temporarily ...................................................................
Saving Settings to Memory and Using Saved Settings .................................................................... 152 Scheduling Projector Events ...................................................................................................
Projector Status Display Messages ............................................................................................. 205 Using the Projector Help Displays .....................................................................................
FCC Compliance Statement ............................................................................................................. 241 Trademarks .....................................................................................................
.
PowerLite Pro Z9870NL/Z11005NL/Z9800WNL/Z9900WNL/ Z11000WNL/Z9750UNL/Z9870UNL/Z10000UNL/Z10005UNL User's Guide Welcome to the PowerLite Pro Z9870NL/Z11005NL/Z9800WNL/Z9900WNL/Z11000WNL/Z9750UNL/ Z9870UNL/Z10000UNL/Z10005UNL User's Guide .
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information.
Flexible connectivity • Wired and wireless network support for projection, monitoring, and control via remote network computer • Variety of connection methods to a computer or video device includi.
Make sure your projector box included all of these parts: 1 Projector 2 Lens unit cap 3 Power cord clip 4 HDMI cable clip 5 Remote control 6 Remote control batteries (two AA alkaline) 7 Power cord 8 V.
Parent topic: Projector Features Related concepts Projector Connections Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To connect a computer through its VGA port to the projector's BNC ports, you need a VGA-to-5-BNC cable or adapter.
Option or part Part number Genuine Epson replacement lamp (dual) (ELPLP82) V13H010L82 Genuine Epson replacement portrait lamp (single) (ELPLP83) V13H010L83 Genuine Epson replacement portrait lamp (dua.
Option or part Part number Short throw zoom lens (ELPLU02) V12H004U02 Rear-projection wide lens (ELPLR04) V12H004R04 Standard zoom lens (ELPLS04) V12H004S04 Middle-throw zoom lens #1 (ELPLM06) V12H004.
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector.
Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Handles 2 Kensington security slot 3 .
7 Projection lens 8 Interface cover latch 9 Interface cover button 10 Cable cover 11 Lens cover 12 Ceiling mount holes Parent topic: Projector Part Locations Projector Parts - Rear 1 Air exhaust vent/.
Parent topic: Projector Part Locations Projector Parts - Interface Ports 1 SDI port (PowerLite Pro Z9870UNL/Z10000UNL/Z10005UNL) 2 BNC ports 3 Video port 4 S-Video port 5 Computer port 6 Power cord cl.
11 Wireless LAN module port 12 Monitor Out port 13 HDMI port 14 HDMI cable clip slot 15 DVI-D port 16 Network LAN port 17 HDBaseT port Parent topic: Projector Part Locations Projector Parts - Base 1 C.
2 Front feet 3 Rear feet Parent topic: Projector Part Locations Projector Parts - Control Panel 1 On button (turns power on) 2 Standby button (turns power off) 3 Source buttons (change input source; s.
8 Shutter button (turns signal on or off temporarily) 9 Test Pattern button (displays a test pattern) 10 Enter button (selects options and controls wireless mouse functions) 11 Arrow buttons (move thr.
Projector Parts - Remote Control 25.
1 On button (turns power on) 2 Standby button (turns power off) 3 Source buttons (change input source; some buttons may not function depending on the model) 4 Aspect button (selects the image aspect r.
26 Shutter button (turns signal on or off temporarily) 27 Color Mode button (selects display modes) 28 Search button (searches for connected sources) 29 Light button (lights up the buttons temporarily.
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Removing and Attaching the Interface Cover Projector Connections Attaching and .
Front Rear Front/Ceiling mounted 29.
Rear/Ceiling mounted Note: Be sure to leave at least 20 inches (50 cm) of space in front of the air exhaust and intake vents and, when setting up multiple projectors, 20 inches (50 cm) of space between the projectors.
If you mount the projector for standard lamp use, you can tilt it at the following angles: • Vertically : Any angle up to ±100°. • Horizontally : Within the range of ±5°. If you mount the projector for portrait lamp use, you can tilt it at the following angles: • Vertically : Any angle up to ±10°.
Note: The optional installation frame (ELPMB44) and portrait lamps (ELPLP83/ELPLP84) are required when using portrait projection. Be sure to mount the projector with the air intake vent facing down and at least 4 inches (10 cm) of space between the projector and the mounting surface as shown.
Set the Direction setting in the Extended menu to one of the following settings so that operations on the screen match the control panel button commands.
Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.
Screen or Projection distance Vertical lens shift image size Wide to Tele Top to Bottom 53 inches 78 to 128 inches (199 to 326 cm) –3 to 35 inches (–8 to 89 cm) 80 inches 119 to 195 inches (304 to.
Screen or Projection distance Vertical lens shift image size Wide to Tele Top to Bottom 56 inches 78 to 128 inches (197 to 324 cm) –6 to 34 inches (–17 to 87 cm) 80 inches 112 to 184 inches (285 t.
Removing and Attaching the Interface Cover Remove the interface cover before installing the projector so that it is easier to connect the cables after installation. 1. Push up and hold the interface cover latch while pressing the button on the side as shown.
3. Align the interface cover with the guides on the projector and slide it until it clicks into place. Parent topic: Setting Up the Projector Projector Connections You can connect the projector to a variety of computer and video sources to display presentations, movies, or other images.
Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector. Connecting to a Computer for VGA Video Connecting to a Computer for HDMI Video Connecti.
Connecting to a Computer for HDMI Video If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.
2. Connect the other end to the projector's DVI-D connector. Parent topic: Connecting to Computer Sources Connecting to a Computer for 5 BNC Video You can connect the projector to your computer using an optional VGA-to-5-BNC cable. 1. Connect the VGA connector to your computer's monitor port.
Connecting to an HDMI Video Source Connecting to a Component-to-BNC Video Source Connecting to a Component-to-VGA Video Source Connecting to an S-Video Video Source Connecting to a Composite Video Sou.
1. Connect the component connectors to your video source's color-coded component video output ports, usually labeled Y , Pb , Pr or Y , Cb , Cr . If you are using an adapter, connect these connectors to your component video cable. 2. Connect the BNC connectors to the projector's R/Cr/Pr , G/Y , B/Cb/Pb ports.
2. Connect the VGA connector to a Computer port on the projector. 3. Tighten the screws on the VGA connector. Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signa.
Parent topic: Connecting to Video Sources Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional BNC-style, composite video cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port.
2. Connect the other end to the projector's SDI port. Parent topic: Connecting to Video Sources Connecting to an HDBaseT Transmitter To send an HDMI or RS-232C signal over a long distance, you can connect the projector to an optional HDBaseT transmitter using a 100Base-TX network cable.
3. Connect the other end to the projector's HDBaseT port. See the documentation that came with the HDBaseT transmitter for instructions on connecting it to your video device or computer.
1. Make sure your computer is connected to the projector's Computer or BNC port. 2. Connect the external monitor's cable to your projector's Monitor Out port. Note: If you do not see an image on the external monitor, you may need to change the Monitor Out setting in the Extended menu.
1. Center the lens using the Lens Shift button. 2. Turn off the projector. 3. Press down on the lens cover and lift it off of the projector. 4. Hold the lens firmly as you slide the lock lever to the Release position (counterclockwise) until you hear it click.
Attaching a Lens You can attach a compatible lens to the projector. Caution: Avoid touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface. 1. Hold the lens with the white dot facing up. Insert the lens straight into the projector's lens socket and turn it clockwise until you hear it click into place.
3. Replace the lens cover. 4. Set the Lens Type setting in the Extended menu for the type of lens you installed. Parent topic: Attaching and Removing a Lens Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the power cord and HDMI cable.
1 Cable clip slot 2 Cable clip anchor 3 Power cable clip 4 HDMI cable clip 3. Place the open cable clips around the power cord and HDMI cable, but do not lock them. 4. Slide each cable clip onto the anchors and lock the clips onto the power and HDMI anchors as shown.
2. Insert the batteries with the + and – ends facing as shown. 3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Setting Up Projector Netw.
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly through the access point using the EasyMP Network Projection software.
Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter .
5. Select the Basic menu and press Enter . 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
7. Select the Wired LAN menu and press Enter . 8. If necessary, select IP Settings and press Enter . 9. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting.
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly through the access point using the EasyMP Network Projection software without the need for the optional wireless module.
Caution: Never remove the LAN module while its indicator light is green or flashing, or while you are projecting wirelessly. You may damage the module or lose data. Note: The wireless LAN module is not included with your projector and is optional. 1. Push up and hold the interface cover latch while pressing the button on the side as shown.
Related references Optional Equipment and Replacement Parts Using Quick Wireless Connection (Windows Only) You can use the Quick Wireless Connection USB key to quickly connect your computer to the projector wirelessly. Then you can project your presentation and remove the key when you are done.
4. Insert the Quick Wireless Connection USB key into the same port used for the wireless LAN module. You see a projected message that the network information update is complete. 5. Remove the USB key. 6. Reinsert the wireless LAN module into the projector.
Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter .
5. Select the Basic menu and press Enter . 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
7. Select the Wireless LAN menu and press Enter . 8. Select the settings on the Wireless LAN menu as necessary for your network. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick : lets you quickly connect to one computer (Ad Hoc) or use the optional Quick Wireless Connect.
Setting Options Description IP Address Display On Selects whether to display the IP address on the network standby Off screen Parent topic: Selecting Wireless Network Settings Manually Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer.
Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button. 2. Select the Network menu and press Enter . 3. Select Network Configuration and press Enter . 4. Select the Security menu and press Enter .
Setting Options Description Passphrase Various keys from 8 to 32 Selects the pre-shared key used characters on the network; passphrases are case-sensitive Parent topic: Setting Up Wireless Network Sec.
7. Select a number for the SMTP server Port Number , from 1 to 65535 (default is 25). 8. Choose an Address field, enter the e-mail address, and select the alerts you want to receive there. Repeat for up to three addresses. Note: Your e-mail address can be up to 32 alphanumeric characters long.
4. Select the Others menu and press Enter . 5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely. Note: The web setup and control features support Microsoft Internet Explorer 8.
You see a screen like this: 1 Power on button control 2 Input source selection controls (some buttons may not be available depending on the model) 3 Freeze button control 4 Shutter button control 5 Page Up and Page Down button controls 6 Source search control 7 Power off button control 6.
1. Make sure the projector is turned on. 2. Start your web browser on a computer connected to the network. 3. Type the projector's IP address into the browser's address box and press the computer's Enter key. You see the Web Control screen.
You see a screen like this: 5. Use the buttons on the screen to adjust the Focus , Zoom , Vertical Lens Shift , and Horizontal Lens Shift features. Parent topic: Controlling a Networked Projector Usin.
For additional information on Crestron RoomView, contact Crestron. Setting Up Crestron RoomView Support Controlling a Networked Projector Using Crestron RoomView Parent topic: Using the Projector on a.
Note: Enabling Crestron RoomView disables the Epson Message Broadcasting feature in the EasyMP Monitor software. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Turn off the projector, then turn it on again to enable the setting.
4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons. You can scroll through button options at the bottom of the screen.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. Turning On the Projector Turning Off the Projector Selecting the Language for the .
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's power light turns blue. This indicates that the projector is receiving power.
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage.
3. Select the Extended menu and press Enter . 4. Select the Language setting and press Enter . 5. Select the language you want to use and press Enter .
You see this screen: 5. Select your screen's aspect ratio and press Enter . 6. Press the Menu button to accept the changes. Note: Adjust the aspect ratio for the projected image.
3. Press the arrow buttons to adjust the position of the projected image as necessary. PowerLite Pro Z9870NL/Z11005NL 1 Center of lens 2 Projected image when lens shift is set in the center 3 Maximum vertical range (V × 56%) 4 Maximum horizontal range (H × 19%) Note: You cannot move the image to both the horizontal and vertical maximum values.
PowerLite Pro Z9800WNL/Z9900WNL/Z11000WNL/Z9750UNL/Z9870UNL/Z10000UNL/Z10005UNL 1 Center of lens 2 Projected image when lens shift is set in the center 3 Maximum vertical range (V × 60%) 4 Maximum horizontal range (H × 18%) Note: You cannot move the image to both the horizontal and vertical maximum values.
2. Press the Menu button. 3. Select the Extended menu and press Enter . 4. Select Display > Screen > Screen Position . 5. Use the arrow buttons on the remote control or projector to adjust the position of the image. 6. When you are finished, press the Menu button.
3. Press the left or right arrow buttons on the remote control or press Enter on the control panel to cycle through the available test patterns. 4. Adjust the image as necessary.
Menu Settings Image Color Mode Color Temp. Advanced • Gamma 1 • RGB • RGBCMY Reset Signal Auto Setup Settings Geometric Correction Extended Multi-Projection 2 1 Except for custom Gamma settings .
If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Related concepts Image Shape Related references Projector Feature Setti.
3. Select the Settings menu and press Enter . 4. Select the Geometric Correction setting and press Enter . 5. Select the H/V-Keystone setting and press Enter .
Related references Projector Feature Settings - Settings Menu Related tasks Displaying a Test Pattern Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides.
You see the Quick Corner adjustment screen: 6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter . 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc .
1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Press the Menu button. 3. Select the Settings menu and press Enter . 4. Select the Geometric Correction setting and press Enter .
6. Select the Correct Shape setting and press Enter . 7. Use the arrow buttons on the projector or the remote control to select the area you want to adjust. Then press Enter . Note: To reset your Curved Surface adjustments, press the Esc button for at least 2 seconds to display a reset screen, and select Yes .
9. Press the Esc button to return to the Curved Surface menu screen. 10. Repeat the previous three steps as necessary to adjust other image areas. If the image expands or contracts, continue with the next step to adjust the linearity.
Related references Projector Feature Settings - Settings Menu Related tasks Displaying a Test Pattern Correcting Image Shape with Point Correction Correcting Image Shape with Point Correction You can use the projector's Point Correction feature to fine-tune the image shape using points on a grid.
The box changes from a single line to a double-lined square. 8. Use the arrow buttons to correct the image shape in all necessary directions. Note: You can press Enter to show or hide the image and grid to check the results. 9. Press Esc to return to the previous screen and select another point to correct, if necessary.
Correcting Image Shape with Corner Wall You can use the projector's Corner Wall setting to adjust the shape of an image projected on a surface with right angles, such as a rectangular pillar or the corner of a room. Note: After performing these steps, the image may not be evenly focused throughout.
You see this screen: 6. Select the Corner Type setting and press Enter . 7. Select one of the following: • Horizontal Corner when the surfaces line up horizontally • Vertical Corner when the surfaces line up vertically 8. Press the Esc button to return to the Corner Wall menu screen.
10. Adjust the projector's position and use the lens shift option to center the image over the point where the two surfaces meet. (The rest of these steps show Horizontal Corner as the selected Corner Type but the steps are the same for Vertical Corner.
Note: To reset your Corner Wall adjustments, press the Esc button for at least 2 seconds to display a reset screen, and select Yes . • For horizontal corners, adjust the top area using the lowest point (indicated by the blue arrow) as your reference and press Enter .
16. Adjust the linearity by doing the following as necessary: • Press and hold the left arrow button to contract the distance between the lines closest to the left or top of the image. • Press and hold the right arrow button to contract the distance between the lines closest to the right or bottom of the image.
2. Press the Zoom button on the projector's control panel or remote control. 3. Press and hold the arrow buttons on the projector's control panel or remote control to resize the image. 4. Press the Esc button on the projector's control panel or remote control when finished.
Focusing the Image with the Optional Short Throw Lens Parent topic: Using Basic Projector Features Related tasks Displaying a Test Pattern Focusing the Image with the Optional Short Throw Lens If you installed the optional short throw lens (ELPLU02) and shifted the lens using the lens shift option, you can focus the image using the distortion ring.
4. Press and hold the arrow buttons to focus the image around the center of the lens. 5. Rotate the distortion ring until the area around the edges of the image is also focused. 6. Press the Focus button again, then press the arrow buttons to focus the entire screen image.
Make sure that you aim the remote control at the projector's receivers within the angles listed here. 1 98 feet (30 m) 2 ±60° 3 +15° 4 ±30° 5 +45° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands.
Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1. Make sure the connected image source you want to use is turned on. 2. For video image sources, insert a DVD or other video media and press its play button, if necessary.
Selecting the Lamp You can select the lamps you want to turn on. 1. Press the Menu button. 2. Select the Extended menu and press Enter . 3. Select the Lamp Select setting and press Enter . 4. Use the arrow buttons on the projector or the remote control to select one of the following options: • Dual (default): Both lamps are on.
• Single : When the projector is turned on, the lamp with the fewest number of total operation hours turns on. If that lamp stops working, the other lamp turns on. • Lamp 1 : Lamp 1 turns on. If Lamp 1 stops working, Lamp 2 turns on. • Lamp 2 : Lamp 2 turns on.
3. Select the Extended menu and press Enter . 4. Select the Projection setting and press Enter . 5. Select a projection mode and press Enter . 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios.
Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. Note: Set the Screen Type setting in the projector's Extended menu before changing the aspect ratio. 1. Turn on the projector and switch to the image source you want to use.
*Available only when projecting computer images or from the HDMI or HDBaseT port Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images in the same aspect ratio of the input signal.
Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use.
Color Mode Description Multi-Projection Best for projecting from multiple projectors (reduces the color tone difference between images) 1 Only available when inputting RGB signals 2 Only available whe.
4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture Temporarily Stopping Video Action Temporarily Zooming .
Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any video action continues to run, however, so you cannot resume projection at the point that you stopped it.
• To pan around the zoomed image area, use the arrow buttons. • To zoom out of the image, press the E-Zoom – button as necessary. • To return to the original image size, press Esc .
Saving a User's Logo Image to Display Parent topic: Projector Security Features Setting a Password To use password security, you must set a password. 1. Hold down the Freeze button on the remote control for about ten seconds or until you see this menu.
6. Press Esc to return to the menu. 7. Make a note of the password and keep it in a safe place in case you forget it. Parent topic: Password Security Types Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want to use.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector.
When you contact Epson Support, provide the displayed request code and proof of ownership for assistance in unlocking the projector. Parent topic: Password Security Types Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on.
You see a prompt asking if you want to select this image area. 6. Select Yes and press Enter . (If you want to change the selected area, select No , press Enter , and repeat the last step.) You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter .
Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button.
Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them. Note: If the remote control buttons have been locked, hold the Help button on the remote control for 5 seconds to unlock them.
Using Multiple Projectors You can combine the projected images from two or more projectors to create one large image. The following two options are available: • Project different images from each pr.
Adjusting the Position of the Projected Image From Multiple Projectors Matching the Image Colors Adjusting the Color Tone (Color Uniformity) Adjusting the Color Convergence (Panel Alignment) Scaling a.
4. Select Projector ID and press Enter . 5. Use the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter . Repeat these steps for all the other projectors you want to operate from one remote control.
3. Hold down the ID button on the remote control while you press the numeric button that matches the projector's ID. Then release the buttons. Note: If you don't know the projector's ID, hold down the ID button and press the Help button to temporarily display the projector's ID on the screen.
Related tasks Displaying a Test Pattern Adjusting the Image Position Using Lens Shift Resizing the Image with the Zoom Button Correcting Image Shape with Quick Corner Correcting Image Shape with Point Correction Matching the Image Colors You can match the display quality of multiple projectors that will project next to each other.
9. Adjust the Brightness setting on the projector with the darkest display so it matches the lighter display, and press Enter . (You may need to switch the remote control ID back and forth to make adjustments to each projector in all of these steps.) 10.
4. Select the Color Uniformity setting and press Enter . 5. Press Enter and select On . 6. Press Esc . 7. Select the Adjustment Level setting and press Enter . 8. Press the right and left arrow buttons to adjust the level, then press Esc . 9. Select the Start Adjustments setting and press Enter .
cm) diagonally and the projection surface should not be colored or textured; otherwise the adjustment grids are difficult to align. 1. Press the Menu button. 2. Select the Extended menu and press Enter . 3. Select the Display setting and press Enter .
10. Select Start Adjustments and press Enter twice. You see this screen: 11. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box. 12. Press the Enter button to move to the next corner of the screen.
14. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter .
5. Select the Scale Mode setting and select one of the following options: • Zoom Display : Maintains the image aspect ratio as you scale the image • Full Display : Adjusts the image to the projector's screen size as you scale the image 6.
Parent topic: Using Multiple Projectors Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other. You can control the split screen feature using the remote control or the projector menus.
5. To change the image sizes, select the Screen Size setting, press Enter , select a sizing option, press Enter , and press Menu to exit. Note: Depending on the video input signals, the images may not appear at the same size even if you choose the Equal setting.
Blending the Image Edges You can use the projector's Edge Blending feature to create a seamless image from multiple projectors. 1. Press the Menu button. 2. Select the Extended menu and press Enter . 3. Select the Multi-Projection setting and press Enter .
You see a screen like this: 7. Select the Blending setting and select On . 8. Select the Blend Range setting and select the width of the blended area. The range should be set so that the displayed guides are at the edges of the overlapping area between the two images.
Adjusting the Black Level When two images overlap, the overlapping area can appear differently from the areas that do not overlap. You can use the projector's Black Level setting to make the difference less noticeable. Note: You cannot adjust the black level when a test pattern displayed.
You see this screen: 5. Select the Color Adjustment setting and press Enter . You see this screen: 6. Adjust the brightness and tone of the areas that do not overlap to match the areas that overlap using the displayed adjustment sliders.
7. Press the Esc button to return to the Black Level menu screen. 8. Select the Area Correction setting and press Enter . You see a screen like this displaying the points you can use to set the range for black level: Note: The points displayed differ depending on the Edge Blending and Point Correction settings.
10. Use the arrow buttons to move the point to the edge of the adjustment area. 11. To move another point, press the Esc button and repeat the previous two steps. 12. When you are finished, press the Esc button twice. 13. When you see the confirmation message, select Yes to return to the Black Level menu screen.
Parent topic: Using Multiple Projectors Saving Settings to a USB Flash Drive You can save the projector settings you want to transfer to a USB flash drive. Note: Use an empty flash drive. If the drive contains other files, the transfer may not complete correctly.
4. When the power, Status, Lamp, and Temp lights turn on, release the Esc button. The lights flash to indicate that settings are transferring to the flash drive. When the lights stop flashing, the power light turns blue and the projector enters standby mode.
3. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When the power, Status, Lamp, and Temp lights turn on, release the Menu button. The lights flash to indicate that settings are transferring to the projector.
1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's Service port.
• OS X: Drag the removable disk icon for your projector from the desktop into the trash. The projector enters standby mode. Parent topic: Copying Menu Settings Between Projectors Transferring Settings From a Computer After saving projector settings to a computer, you can transfer them to another projector of the same model.
3. Connect the other end to any available USB port on your computer. 4. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When the power, Status, Lamp, and Temp lights turn on, release the Menu button.
Using Frame Interpolation You can use the projector's Frame Interpolation feature to smooth fast-moving video by comparing consecutive image frames and inserting an intermediate image frame between them (PowerLite Pro Z9750UNL/Z9870UNL/Z10000UNL/Z10005UNL).
5. When you are finished, press the Menu button. Note: If your resulting images contain noise, turn off the Frame Interpolation setting. Parent topic: Adjusting Projector Features Viewing 3D Images Us.
You see this screen: 5. Select one of the following options: • Load Memory : Overwrites your current settings with saved settings • Save Memory : Saves your current settings to memory (10 memories with different names are available) Note: A memory name that has already been used is indicated by a blue mark.
Note: The Time/Schedule Protection setting in the Password Protection menu must be turned off to schedule an event. Saving a Scheduled Event Viewing Scheduled Events Editing a Scheduled Event Parent topic: Adjusting Projector Features Saving a Scheduled Event You can select projector commands you want to perform and schedule them as an event.
You see a screen like this: The colored boxes in the calendar indicate the following about the scheduled events: One-time event Reoccurring event Communication is on/off Event is invalid Parent topic: Scheduling Projector Events Editing a Scheduled Event You can edit any currently scheduled event.
You see a screen like this: 4. Press the left or right arrow buttons to highlight the date on the calendar containing the scheduled event you want to edit. 5. Press the up or down arrow buttons to highlight the event you want to edit, and press Esc . 6.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings. Using the Projector's Menus Image Quality Settings - Image.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source.
Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Sharpness Varying levels available Adjusts the sharpness or softness of image details Color Temp. 3200, 5000, or 10000 ºK (Kelvin), Sets the color tone based on or –3 to.
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
Setting Options Description Resolution Auto Sets the input signal resolution from an analog RGB computer Normal connection Wide Auto : detects the resolution Manual automatically Normal : for 4:3 or 5.
Setting Options Description Super-resolution Varying levels available Reduces edge blurring that may occur when image is scaled up to fit the resolution of the image signal Noise Reduction Off Reduces.
Setting Options Description Aspect See the list of available aspect Sets the aspect ratio (width-to- ratios height ratio) for the selected input source Scale Various scale options When using multiple .
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. 165.
Setting Options Description Geometric Correction Off Adjusts the projected image shape H/V-Keystone H/V Keystone : lets you manually Quick Corner correct the angles of the Curved Surface horizontal an.
Setting Options Description Power Consumption Normal Selects the brightness mode of the projector lamp Temp Interlock Normal : sets maximum lamp ECO brightness Temp Interlock : automatically dims the .
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Display — See the Di.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is Front/Upside Down oriented correctly Rear Rear/Upside Down Direction Varying levels availabl.
Setting Options Description Standby Mode Communication On Enable this setting to allow the following operations to occur Communication Off when the projector is in standby mode: • Monitor and contro.
Setting Options Description Schedule Settings — Schedule specific operations to occur at a pre-scheduled time Language Various languages available Selects the language for projector menu and message.
Setting Options Description Color Uniformity — Adjusts the color tone balance Operation settings Setting Options Description Direct Power On — Turns on the projector when you plug it in Sleep Mode.
Setting Options Description Projector ID — Sets the projector to a particular ID number which allows you to use a remote control to individually control projectors Scale — Adjusts the size of the .
Setting Options Description Remote Control Type — Select Normal to use the remote control that came with the projector or Simple to use a different Epson projector remote control (disables the remot.
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wired LAN Projector Name Displays wired network status and details DHCP IP Address Subnet Mask Gateway Address MAC Address Network Configuration Accesses additi.
Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Setting Options Description Refresh Rate — Displays the refresh rate of the current input source Sync Info — Displays information that may be needed by a service technician Status — Displays inf.
Event ID code Cause and solution 0434 Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0482 0484 0485 0433 Cannot display the transferred images. Restart the EasyMP Network Projection program.
You can also reset the saved names and settings in the Save Memory list using the Reset Memory option. You cannot reset the following settings using the Reset All option: • Input Signal • User&apo.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Related concepts Projector Status Display Related references Projector Light Status Cleaning the Air Filter You need to clean the projector's air filter in the following situations: • The filter or vents get dusty. • You see a message telling you to clean it.
3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.
7. Attach the air filter cover as shown, and press it gently until it clicks into place. Parent topic: Air Filter and Vent Maintenance Related concepts Projector Status Display Related references Proj.
2. Press and hold the tab on the air filter cover, and pull to remove the cover. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene.
4. Place the new air filter in the projector as shown. 5. Attach the air filter cover as shown, and press it gently until it clicks into place. Parent topic: Air Filter and Vent Maintenance Related co.
Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
3. Slide the lamp cover latch to the Open position and slide the lamp cover to the left. 4. Open the lamp cover. 190.
5. Pull up the lock lever for the lamp you want to replace and pull the lamp straight out of the projector. 1 Lamp 1 2 Lamp 2 Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling.
6. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 7. Flip down the lock lever and press until it clicks into place.
9. Slide the lamp cover to the right until it clicks, and slide the lamp cover latch to the Close position. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage.
2. The following message is displayed on the screen: 3. Select Yes and press Enter . The count for the lamp you replaced will return to 0 hours. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries.
1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box "Fragile." Note: Epson shall not be liable for any damages incurred during transportation.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Projector Status Display Using the Projector Help Di.
Projector Light Status The lights on the projector's control panel indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp Temp light Filter light Status and solution lights Blue Blue On Off Off Normal operation. Blue Flashing Off Off Off Warming up. Wait for an image to blue appear. Blue Off Off Off Off Standby or sleep mode. Flashing Off Off Off Off Preparing network monitoring or blue shutting down.
Power light Status light Lamp Temp light Filter light Status and solution lights Off Flashing Off Flashing Off Fan or sensor error. Projector has blue orange overheated and turned off. Leave it turned off to cool down for five minutes. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
Power light Status light Lamp Temp light Filter light Status and solution lights Blue Off Off Off Flashing Clean the air filter. orange Blue Flashing Off Off Flashing Low air flow through the projector blue orange or air filter. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Projector Feature Settings - Settings Menu Where to Get Help Related tasks Cleaning the Air Filter Replacing .
1 Status menu setting 2 Information about status setting If a problem occurs, an error or warning message appears on the status screen. Press an arrow button to return the status screen to its normal state.
Adjusting the Projector Status Display You can adjust the contrast and the backlight duration on the status display screen. 1. Press the right or left arrow button to select the Setting menu. 2. Press the down arrow button to display the Contrast . 3.
Selection Options Description On-Screen Display On Displays the settings for the On- Screen Display . When set to Off Off , the menus or messages are not displayed on the projected images Shutter Open.
Selection Options Description Source Computer Displays the source currently being used BNC Video S-Video HDMI DVI-D SDI LAN HDBaseT Resolution — Displays the resolution of the current input signal V.
Selection Options Description 5V Detect — Displays the detection results of 5V signals TMDS Clock — Displays the TMDS frequency of the current input signal TMDS H-Frequency — Displays the horizo.
Selection Options Description HDBaseT Quality — Displays the image signal information from the HDBaseT port Network Wired menu Selection Options Description Projector Name — Displays the name used.
Selection Options Description SSID — Displays the SSID IP Address — Displays the IP address DHCP — Displays the DHCP settings MAC Address — Displays the MAC address Security No Displays the se.
Setting menu Selection Options Description Contrast Level Adjusts the contrast for the LCD screen Lighting Time Off Selects the duration of time for the status screen display 10 to 60 sec Approx.
Status Description Lamp2 Failure (S) A Lamp 2 failure occurred S : indicates a standard lamp Lamp2 Failure (P) P : indicates a Portrait mode lamp Power1 Error A power error occurred Power2 Error Inter.
Parent topic: Projector Status Display Related references Projector Setup Settings - Extended Menu Projector Feature Settings - Settings Menu Input Signal Settings - Signal Menu Optional Equipment and.
Solutions When No Image Appears If no image appears, try the following solutions: • Press the Shutter button on the remote control to see if the image was temporarily turned off. • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
• Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary. • Check the connection from the projector to your video sources. • If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.
Solutions When "Not Supported " Message Appears If the "Not Supported" message appears, try the following solutions: • Make sure the correct input signal is selected on the Signal menu. • Make sure the computer's display resolution does not exceed the projector's resolution and frequency limit.
Solutions When the Image is Not Rectangular If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. • Adjust the image shape using the Geometric Correction menu settings.
Supported Video Display Formats Related tasks Displaying From a PC Laptop Displaying From a Mac Laptop Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens.
Solutions When the Image Brightness or Colors are Incorrect If the projected image is too dark or light, or the colors are incorrect, try the following solutions: • Press the Color Mode button on the remote control to try different color modes for the image and environment.
Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet.
• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release the button to wake the remote control up. • Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the projector's remote receivers.
Parent topic: Solving Projector or Remote Control Operation Problems Solutions When Network Alert E-Mails are Not Received If you do not receive an e-mail alerting you to problems with a projector over the network, try the following solutions: • Make sure the projector is turned on and connected to the network correctly.
Days and hours of support are subject to change without notice. Toll or long distance charges may apply. Before you call, have the following information ready: • Product name • Product serial numb.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dime.
Brightness Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.
PowerLite Pro Z9800WNL : Normal Power Consumption mode: White light output 8300 lumens (two lamps) or 4150 (one lamp) (ISO 21118 standard) Color light output 8300 lumens (two lamps) or 4150 (one lamp).
PowerLite Pro Z11000WNL : Normal Power Consumption mode: White light output 11000 lumens (two lamps) or 5500 (one lamp) (ISO 21118 standard) Color light output 11000 lumens (two lamps) or 5500 (one la.
PowerLite Pro Z9870UNL : Normal Power Consumption mode: White light output 8700 lumens (two lamps) or 4350 (one lamp) (ISO 21118 standard) Color light output 8700 lumens (two lamps) or 4350 (one lamp).
Projection distance 78.3 inches (1.99 m) to 676 inches (17.17 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:10 (width-to-height) Focus adjustment Powered, manual Zoom adjustment Powered, manual Zoom ratio 1 to 1.
Lamp life Normal Power Consumption mode: (standard lamps) PowerLite Pro Z9870NL/Z9800WNL/Z9750UNL : Up to about 3000 hours (using two lamps) PowerLite Pro Z9900WNL/Z9870UNL : Up to about 2500 hours (u.
Weight PowerLite Pro Z9870NL/Z9800WNL/Z9750UNL : (including standard lens) Approximately 56 lb (25 kg) PowerLite Pro Z11005NL/Z9900WNL/Z11000WNL/Z9870UNL/ Z10000UNL/Z10005UNL : Approximately 58 lb (26.
Power consumption Operating: (100 to 120 V; using two PowerLite Pro Z9870NL/Z9800WNL/Z9750UNL : standard lamps) Normal Power Consumption mode: 844 W ECO Power Consumption mode: 748 W PowerLite Pro Z99.
Projector Environmental Specifications Temperature Operating: 32 to 122 °F (0 to 50 °C) up to 4921 feet (1500 m) altitude with Power Consumption set to ECO or Temp Interlock 32 to 113 °F (0 to 45 .
Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.) The table here lists the compatible refresh rate and resolution for each compatible video display format.
Display format Refresh rate (in Hz) Resolution (in pixels) TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 576 Component video SDTV (480i) 60 720 × 480 SDTV (576i) 50 720 × 576 SDTV (480p) 60 720 × .
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 SDI input signals 5 SDTV (480i) 60 720 ×.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention device.
For Canadian Users CAN ICES-3(B)/NMB-3(B) Parent topic: Notices Trademarks EPSON ® , EasyMP ® , Instant Off ® , PowerLite ® , and Quick Corner ® are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs The list of GPL Programs busybox-1.
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or an.
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-read.
For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
Gnomovision version 69, Copyright (c) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type 'show w'. This is free software, and you are welcome to redistribute it under certain conditions; type 'show c' for details.
The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc.
have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program.
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License").
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplie.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for.
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.
that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code. The IJG distribution formerly included code to read and write GIF files.
Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant and with the following additions to the disclaimer: There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs.
Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose.
License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows. Copyright notice: (c) 1995-1998 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty.
http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives. Copyright [yyyy] [name of copyright owner] Licensed under the Apache License, Version 2.
This software is provided 'as is' with no explicit or implied warranties in respect of its properties, including, but not limited to, correctness and/or fitness for purpose.
* Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. (4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc.
(8) Hewlett Packard (c) Copyright 1986 HEWLETT-PACKARD COMPANY To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy,.
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (12) SuperH, Inc. Copyright 2002 SuperH, Inc.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMA.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE PRODUCT LICENSED HEREUNDER.
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR C.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
(35) - ARM Ltd (arm and thumb variant targets only) Copyright (c) 2009 ARM Ltd All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED. IN NO EVENT SHALL CODESOURCERY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDI.
MIT License This projector product includes the open source software program which applies the terms and conditions provided by owner of the copyright to the "MIT License". The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TOPPERS/JSP Kernel Toyohashi Open Platform for Embedded Real-Time Systems/Just Standard Profile Kernel Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of Technology, JAPAN Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory Graduate School of Information Science, Nagoya Univ.
This projector product includes the open source software program "TINET" which applies the terms and conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of Technology, JAPAN TINET (TCP/IP Protocol Stack) Copyright (C) 2001-2006 by Dep.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.
Een belangrijk punt na aankoop van elk apparaat Epson Z10000UNL (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Epson Z10000UNL heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Epson Z10000UNL vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Epson Z10000UNL leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Epson Z10000UNL krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Epson Z10000UNL bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Epson Z10000UNL kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Epson Z10000UNL . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
