Gebruiksaanwijzing /service van het product AT-GS950/24 van de fabrikant Allied Telesis
Ga naar pagina of 44
613-001499 Rev B AT-GS950/24 Gigabit Ethernet Smar t Switch How to Start a WEB Management Session.
Copyright © 2011 Allied Telesis, Inc. All rights reserved. No part of this pub lication may be reproduced without prior wri tten permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated.
3 How to S tart an A T -GS950/24 WEB Management Session This document contains the procedu res to start you Web management session on the AT-GS950/24 switch.
How to Start an AT-GS950/24 WEB Management Session 4 Establishing a Remote Connectio n to the Web Brow ser Interface The AT-GS950/24 switch is shipped with a pre-assigned IP a ddress of 192.168.1.1. After your initial login, you may want to assign a n ew IP address to your switch.
How to Start an AT-GS950/2 4 WEB Management Session 5 The A T -S109 Management Sof tware displays the login dialog box, shown in Figure 2. Figure 2. Management Login Dialo g Box 3. Enter the AT-S109 management login u ser name and password. The default user name is “manager” and the defa ult password is “friend.
How to Start an AT-GS950/24 WEB Management Session 6 Figure 3. AT-S109 Home Pag e The main menu appears on the left side an d is common for all of the management pages discussed in this manual. It consists of the following folders and web pages: Switch Info.
How to Start an AT-GS950/2 4 WEB Management Session 7 5. To see the front panel of the switch, select Front Panel from the main menu on the left side of the page. The A T -S109 Management sof tware displays the front of th e switch. Ports that have a link to an end node are green.
How to Start an AT-GS950/24 WEB Management Session 8 Web Browser Tools You can use the web browser tools to move around the management pages. Selecting Back on your browse r’s toolbar returns you to the previous display. You can also use the browser’s bookmark featu re to save the link to the switch.
How to Start an AT-GS950/2 4 WEB Management Session 9 Configuration of IP Address, Subnet Mask and Gateway Address This procedure explains how to chang e the IP address, subnet ma sk, and gateway address of the switch.
How to Start an AT-GS950/24 WEB Management Session 10 System Default Gatewa y - Displays the default gateway of the switch. To change the default gatewa y, enter a new gateway. When DHCP is enabled, you cannot change this parameter. DHCP Mode - For information about setting this parameter, refer to “DHCP Client Configuration” on page 18.
How to Start an AT-GS950/2 4 WEB Management Session 11 IP Access List Configuration When the IP Access List feature is enabled, remote access to the AT-S109 management software is restricted to the IP addresses entered into the IP Access List.
How to Start an AT-GS950/24 WEB Management Session 12 Note You can add up to 10 IP addre ss to the IP Access List table..
How to Start an AT-GS950/2 4 WEB Management Session 13 5. From the IP Restriction Status field, select one of the following choices from the pull-down menu: Enable - This selection restricts the access to the AT-S109 management software to the IP addresses in the table listed under Accessible IP .
How to Start an AT-GS950/24 WEB Management Session 14 System Time The procedures in this section describe how to configure the system time by manually entering the time or through SNTP an d how to configure the daylight savings time feature.
How to Start an AT-GS950/2 4 WEB Management Session 15 3. Use the pull down menu to set the Clock Mode parameter to Local time. 4. In the Local Time Settings section, set the Date Setting (YYYY:MM:DD) to the current date in the YYYY:MM:DD format.
How to Start an AT-GS950/24 WEB Management Session 16 Setting Daylight Savings Parameters If you want to configure the switch f or daylight savings time, perform the following procedure: 1. From the main menu on the left side of the page, click the System folder.
How to Start an AT-GS950/2 4 WEB Management Session 17 DHCP and ATI Web Discovery Tool The AT-GS950/24 Gigabit Ethernet Smart swit ch is managed through a web browser interface only.
How to Start an AT-GS950/24 WEB Management Session 18 DHCP Client Configuration This procedure explains how to activate and deactivate the DHCP client on the AT-GS950/24 switch. When the clien t is activated, the switch obtains its IP configuration including an IP address an d subnet mask from a DHCP server on your network.
How to Start an AT-GS950/2 4 WEB Management Session 19 Note The ATI Web Discovery Tool is available for downlo ad on the AT-GS950/24 product page at alliedtelesis.
How to Start an AT-GS950/24 WEB Management Session 20 DHCP Auto Configuration If you need to automatically update the switch’s configuration files via a remote server, the DHCP Auto Co nfiguration feature is ava ilable for this purpose via the DHCP server.
How to Start an AT-GS950/2 4 WEB Management Session 21 System Management Information This section explains how to assi gn a name , location, and contact information for the AT- GS950/24 switch. This information helps in identifying each specific AT-GS9 50/24 switch among other switches in the same local area network.
How to Start an AT-GS950/24 WEB Management Session 22 System Name - Specifies a n ame for the switch, for example, Sales. The name is option al and may contain up to 15 characters. System Location - Sp ecifies the location of the switch. The location is optional and may contain up t o 30 characters.
How to Start an AT-GS950/2 4 WEB Management Session 23 User Name and Password Configuration Password protection is always enabled for access to th e AT-S109 Management software. This sectio n explains how to create new users names and passwords and how to mod ify or delete existing users for the web interface.
How to Start an AT-GS950/24 WEB Management Session 24 4. To add a password that corresponds to the use r name entered in step 3, enter a password of up to 12 a lphanumeric characters in the box next to the Password field. The P asswor d field is case sensitive.
How to Start an AT-GS950/2 4 WEB Management Session 25 Delete User Name and Password To delete a user name that you hav e previously added, perform the following procedure. 1. From the main menu on the left side of t he page, click the System folder. The System folder expands.
How to Start an AT-GS950/24 WEB Management Session 26 User Interface Configuration This procedure explains how to enable and disable the user interfaces on the switch. With this procedure you can enable or disable the AT-GS950/ 24 SNMP Agent. For more information about SNMP, see the AT-GS950 Web User Guide.
How to Start an AT-GS950/2 4 WEB Management Session 27 5. From the main menu on the left side of t he page, select Save Configuration to Flash to perman ently save your changes. User Interface Timeout To set the Web Idle Time out, perform the following procedure: 1.
How to Start an AT-GS950/24 WEB Management Session 28 System Information Display The Switch Information page is initially displayed when you first log into the AT-GS950/24 switch. It provides general information about the switch. To view this information, perform the follo wing procedure: 1.
How to Start an AT-GS950/2 4 WEB Management Session 29 Administration Information Section: Switch Name - This paramet er displays the name assigned to the switch. To assign the switch a name, refer to “System Management Information” on page 21. Switch Location - This p arameter displays the location of the switch.
How to Start an AT-GS950/24 WEB Management Session 30 Switch Reboot You can reboot the AT-GS950/24 switch b y either pressing the front panel eco-friendly switch between 5 to 9 seconds or by using the Normal reboot function provided in the AT-S109 management software.
How to Start an AT-GS950/2 4 WEB Management Session 31 Caution Since you define this password as part of the process o f disabling this function, Allied Telesis has no knowledge of it. You ar e responsible for keeping the password in a safe place. If it is lost, Allied Telesis does not have a way to help you recover it.
How to Start an AT-GS950/24 WEB Management Session 32 Figure 14. Factory Default Reset/Reboot Page 3. Go to the lower part of the page to the Reb oot section.
How to Start an AT-GS950/2 4 WEB Management Session 33 Caution This procedure causes the switch to re boot. The switch does not forward network traffic during th e reboot process.
How to Start an AT-GS950/24 WEB Management Session 34 5. Click Apply . The switch begins the reboot process. You must wa it approximately two minutes for the switch to complete the re boot process before you can re-establish your management session and network traffic begins flowing normally again.
How to Start an AT-GS950/2 4 WEB Management Session 35 Figure 15. Factory Default Reset/Reboot Page with Password Entry 5. In the New Password field, enter a passwo rd of up to 12 characters in length. It is case-sensitive. There is not a default password for this field.
How to Start an AT-GS950/24 WEB Management Session 36 Enabling Factory Default Reset If the Factory Default Reset featu re is disabled and you choose to Enable it, perform the following procedure: 1. From the main menu on the left side of the page, select the Tools folder.
How to Start an AT-GS950/2 4 WEB Management Session 37 Pinging a Remote System This procedure instructs the AT-GS9 50/24 switch to ping a node on your network. This pr ocedure is useful in determining whether a n active link exists between the switch and anoth er network device.
How to Start an AT-GS950/24 WEB Management Session 38 5. To view the ping results, click Show Ping Re sults . A sample Ping Test Results Page is displayed. See Figure 19. Figure 19. Ping Test Results Page The following information is displayed: Destination IP Address - Indicates the IP address of the unit that receives the ping.
How to Start an AT-GS950/2 4 WEB Management Session 39 SSL Settings The AT-GS950/24 switch has a web bro wser server for remote management of the unit with a web browser application from managemen t workstations on your network.
How to Start an AT-GS950/24 WEB Management Session 40 4. Click Apply . The SSL setting that you have selected is now active. 5. From the main menu on the left side of the page, select Save Configuration to Flash to permanent ly save your changes.
How to Start an AT-GS950/2 4 WEB Management Session 41 System Log Configuration The System log is designed to monitor the operation the AT-GS950/24 switch by recording the event messa ges it generates during normal operation.
How to Start an AT-GS950/24 WEB Management Session 42 3. From the Syslog Status field, select o ne of the follo wing choices from the pull-down men u: Enable - The System log is active.
How to Start an AT-GS950/2 4 WEB Management Session 43 Returning the AT-S109 Management Software to the Factory Default Values This procedure returns all AT-S109 Man agement software parameters to their default values and deletes all tagge d and port-based VLANs on the switch.
How to Start an AT-GS950/24 WEB Management Session 44 Quitting a Web Browser Management Session To exit a web browser management session, clo se the web browser.
Een belangrijk punt na aankoop van elk apparaat Allied Telesis AT-GS950/24 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Allied Telesis AT-GS950/24 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Allied Telesis AT-GS950/24 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Allied Telesis AT-GS950/24 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Allied Telesis AT-GS950/24 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Allied Telesis AT-GS950/24 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Allied Telesis AT-GS950/24 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Allied Telesis AT-GS950/24 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
