Gebruiksaanwijzing /service van het product AT-IFS802SP van de fabrikant Allied Telesis
Ga naar pagina of 101
613-001690 Rev.A AT-IFS802SP 8x10/100TX POE Layer 2 Ma naged Industrial Switch AT-IFS802SP Installation and User’s Guide.
Copyright © 2012 Allied Telesis, Inc. All rights reserved. No part of this pub lication may be reproduced without prior wr itten permission from Al lied Telesis, Inc. Allied Telesis and th e Allied Telesis logo are trademarks of Allied Telesis, Incor porated .
3 Electrical Safety and Emissions S tandards This product meets the following standards. RFI Emissions FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE .
4.
5 Pr eface This manual is the installation and manage ment guide for the AT-IFS802SP 8x10/100TX POE Layer 2 Managed Industria l Switch. The instructions in this guide explain how to install the switch, st art a management session, and use the CLI and web management inte rfaces.
Preface 6.
3 A T -IFS802SP -80 User Manual Content Chapter 1 Intr oduction ......................................................................... 6 1.1 Hardwar e Featur es .......................................................................................
4 A T -IFS802SP-80 User Manual 6.9 Fault Rela y Alarm ........................................................................................................................ 36 6.10SNTPConguration .........................................
5 A T -IFS802SP-80 User Manual VLAN Commands Set ....................................................................................................................... 81 Spanning T r ee Commands Set ..................................................
6 A T -IFS802SP-80 User Manual Chapt er 1 Introduction The 8 10/100TX + 2 10/100/1000T/SFP Combo with X-Ring L2 Managed Industrial Switch is a cost-effective solution and meets the high reliability requir ements demanded by industrial a pplications.
7 A T -IFS802SP-80 User Manual Network Cable 10Base-T : 2-pair UTP/STP Cat. 3, 4, 5/ 5E cable EIA/TIA-568 100-ohm (100m) 100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable EIA/TIA-568 100-ohm (100m) 1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable EIA/TIA-568 100-ohm (100m) Optical Fiber Multi-mode: 50/125um~62.
8 A T -IFS802SP-80 User Manual 1.2 Softwar e F eatures Management SNMP v1 v2c, v3/ W eb/T elnet/CLI/NS-View SNMP MIB RFC 1215 T rap , RFC1213 MIBII, RFC 1157 SNMP MIB, RFC 1493 Bridge MIB, RFC 2674 VLAN MIB, RFC 1643 , RFC 1757, RSTP MIB, Private MIB, LLDP MIB VLAN P or t Based VLAN IEEE 802.
9 A T -IFS802SP-80 User Manual Rela y Alarm Pr ovides one rela y output for port breakdown, pow er fail Alarm Rela y curr ent carr y ability: 1A @ DC24V SNMP T ra p Up to 3 T ra p stations Cold start,.
10 A T -IFS802SP-80 User Manual Chapt er 2 Hardwar e Description In this paragra ph, it will describe the Industrial switch’ s hardwar e spec, por t, cabling inf ormation, and wiring installation. 2.1 Ph ysical Dimension 8 10/100TX + 2 10/100/1000T/SFP Combo with X-Ring L2 Managed Industrial Switch dimension (W x D x H) ar e 72mm x 105mm x 152mm.
11 A T -IFS802SP-80 User Manual 2.3 T op View The top panel of the 8 10/100TX + 2 10/100/1000T/SFP Combo with X-Ring L2 Managed Industrial Switch has one terminal block connector of tw o DC power inputs and one fault alarm.
12 A T -IFS802SP-80 User Manual 2.4 LED Indicators The diagnostic LEDs that pro vide real-time information of system and optional status are located on the fr ont panel of the industrial switch. The f ollowing table provides the description of the LED status and their meanings for the s witch.
13 A T -IFS802SP-80 User Manual Chapt er 3 Hardwar e Installation In this paragraph, we will describe how to install the 8 10/100TX + 2 10/100/1000T/SFP Combo with X-Ring L2 Managed Industrial Switch and the installation points attended to it. 3.1 Installation Steps Unpack the Industrial switch 1.
14 A T -IFS802SP-80 User Manual 3.2 DIN-Rail Mounting The DIN-Rail is scr ewed on the industrial switch when out of factor y . If the DIN-Rail is not scr ewed on the industrial switch, please see the following pictures to scr ew the DIN-Rail on the switch.
15 A T -IFS802SP-80 User Manual 3.3 W all Mount Plate Mounting Follo w the steps below to mount the industrial switch with wall mount plate. Remov e the DIN-Rail from the industrial s witch; loose the scre ws to remov e the DIN-Rail. 1. Place the wall mount plate on the r ear panel of the industrial switch.
16 A T -IFS802SP-80 User Manual 3.4 Wiring the P o w er Inputs Please follow the steps belo w to inser t the pow er wire. Insert A C or DC pow er wires into the contacts 1 and 2 for po wer 1, or 5 and 6 for pow er . 1. Tighten the wire-clamp scr ews f or prev enting the wires fr om loosing.
17 A T -IFS802SP-80 User Manual 3.5 Wiring the F ault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below . Inserting the wires, the switch will detect the fault status of the power failur e , or port link failure (a vailable for managed model) and then forms an open circuit.
18 A T -IFS802SP-80 User Manual 3.6 Cabling Use four twisted-pair , Categor y 5e or above cabling for RJ-45 por t connection. The cable between • the switch and the link par tner (switch, hub, workstation, etc .) must be less than 100 meters (328 ft.
19 A T -IFS802SP-80 User Manual T o remo ve the LC connector fr om the transceiver , please follo w the steps shown below: First, press the upper side of the LC connector to r elease from the transceiv er and pull it out. Second, push down the metal loop and pull the transceiver out b y the plastic handle .
20 A T -IFS802SP-80 User Manual Chapt er 4 Netw ork Application This chapter pr ovides some sample applications to help user to ha ve more actual idea of industrial switch function application. A sample application of the industrial s witch is shown as below: 4.
21 A T -IFS802SP-80 User Manual 4.2 Coupling Ring Application In the network, it ma y ha ve more than one X-Ring gr oup. By using the coupling ring function, it can connect each X-Ring for the redundant backup . It can ensure the transmissions between two ring gr oupsnot tofail.
22 A T -IFS802SP-80 User Manual 4.3 Dual Homing Application Dual Homing function is to pre vent the connection lose from between X-Ring gr oup and upper lev el/ core switch. Assign two por ts to be the Dual Homing por t that is backup por t in the X-Ring gr oup.
23 A T -IFS802SP-80 User Manual Chapt er 5 Console Manag ement 5.1 Connecting to the Console P or t The supplied cable which one end is RS-232 connector and the other end is RJ-45 connector . Attach the end of RS-232 connector to PC or terminal and the other end of RJ-45 connector to the console port of the switch.
24 A T -IFS802SP-80 User Manual 5.3 Lo gin in the Console Interface When the connection between Switch and PC is ready , turn on the PC and run a terminal emulation pr ogram or Hyper T ermina.
25 A T -IFS802SP-80 User Manual 5.5 Commands Le v el Modes Access Method Pr ompt Exit Method About This Mode1 User EXEC Begin a session with your s witch. switch> Enter logout or quit. The user commands a vailable at the user lev el are a subset of those a vailable at the privileged lev el.
26 A T -IFS802SP-80 User Manual 1. Launch the Internet Explorer on the PC 2. K ey in “http:// “+” the IP address of the s witch”, and then Press “Enter”. Chapt er 6 W eb-Based Mana gement Thissectionintr oducesthecongurationandfunctionsofthe W eb-Basedmanagement.
27 A T -IFS802SP-80 User Manual 3. The login screen will appear right after 4. K eyintheusernameandpass word. Thedefaultusernameandpass wordar ethesameas ‘r oot’. 5. Press Enter or click the OK button, and then the home scr een of the W eb-based management appears.
28 A T -IFS802SP-80 User Manual 6.5IPConguration The switchis a netw ork de vice which needs to be assigned an IP addressfor being identied on the network. Users ha ve to decide a means of assigning IP ad dress to the switch.
29 A T -IFS802SP-80 User Manual 6.6 DHCP Ser ver DHCP is the abbr eviation of Dynamic Host Conguration Protocol that is a pr otocol for assigning dynamic IP addr esses to devices on a network. With dynamic addr essing, a de vice can ha ve a diff erent IP address every time it connects to the network.
30 A T -IFS802SP-80 User Manual 6.6.2 Client Entries When the DHCP ser ver function is enabled, the system will collect the DHCP client information including the assigned IP address, the MA C ad dress of the client device , the IP assigning type, status and lease time.
31 A T -IFS802SP-80 User Manual 6.7 TFTP It pro vides the functions allowing the user to update the switch rmwar e via the T rivial File T ransfer Pr otocol(TFTP)ser v er .
32 A T -IFS802SP-80 User Manual BackupCongurationinterface Y ou can back up the cur rent conguration from ash R OM to the TFTP server f or the purpose of reco vering the conguration later .
33 A T -IFS802SP-80 User Manual SyslogCongurationinterface SimpleMail T ransferPr otocol(SMTP)isthestandar dforemailtransmissionsacr ossthenetw ork.
34 A T -IFS802SP-80 User Manual SMTPCongurationinterface Ha ving ticked the Syslo g/SMTP checkbox es, the ev ent log/email aler t will be sent to the system log ser ver and the SMTP ser ver respectiv ely .
35 A T -IFS802SP-80 User Manual P or t e vent selection • : Also , before the dr op-down menu items are a vailable , the Syslog Client Mode selection item on the Syslog Conguration tab and the E-mail Aler t selection item on the SMTPCongurationtabmustbeenabledrst.
36 A T -IFS802SP-80 User Manual 6.9 F ault Rela y Alarm The Fault Rela y Alarm function pro vides the Pow er Failure and P or t Link Down/Br oken detection.
37 A T -IFS802SP-80 User Manual SNTP Client • : Enable/disable SNTP function to get the time fr om the SNTP ser ver . Da ylight Saving Time • : This is used as a control switch to enable/disable da ylight sa ving period and da ylight sa ving offset.
38 A T -IFS802SP-80 User Manual SNTP Sev er URL • : Set theSNTP ser ver IPad dress. Y ou can assigna localnetw ork timeserver IP addr ess or an internet time ser ver IP addr ess.
39 A T -IFS802SP-80 User Manual 6.11 IP Security IPsecurityfunctionallo wstheusertoassign10specicIPad dressesthatha vepermissionto manage the switch thr ough the http and telnet ser vices for the securing switch management.
40 A T -IFS802SP-80 User Manual 6.12 User Authentication Change web management login user name and pass wor d for the management security issue . User name • : T ypeinthenewuser.
41 A T -IFS802SP-80 User Manual P or t Statistics interface 6.14 P or t Control In Portcontr ol you cancongur ethe settingsof eachport tocontr ol theconnection parameters, and the status of each port is listed beneath.
42 A T -IFS802SP-80 User Manual P or t Control interface 6.15 P or t T runk P or t trunking is the combination of sev eral ports or network cables to expand the connection speed bey ond the limits of any one single por t or netw ork cable.
43 A T -IFS802SP-80 User Manual W ork por ts • : This column eld allows the user to type in the total number of active por t up to f our .
44 A T -IFS802SP-80 User Manual LA CP disabled • Ha ving set up the aggregator setting with LA CP disabled, you will see the local static trunk gr oup information on the tab of Aggregator Inf ormation .
45 A T -IFS802SP-80 User Manual Assigning 2 ports to a trunk group with LA CP disabled Static T runking Gr oup information LA CP enabled • Ha ving set up the aggregator setting with LA CP enabled, you will see the trunking group information betw een two switches on the tab of Aggr egator Information .
46 A T -IFS802SP-80 User Manual Switch2conguration Switch2congurationinterface 1. Set System Priority of the trunk group . The default is 1.
47 A T -IFS802SP-80 User Manual Ha ving set up the LA CP aggregator on the tab of Aggr egator Setting, you can congure the state activityforthemembersof theLA CPtrunk gr oup.
48 A T -IFS802SP-80 User Manual 6.16 P or t Mirr oring TheP or tmir roring isamethod formonitortrafc inswitched networks.
49 A T -IFS802SP-80 User Manual 6.17 Rate Limiting Y oucansetupeverypor t’ sbandwidthrateandframelimitationtype . Ingress Limit F rame type • : select the frametype thatwants to lter .
50 A T -IFS802SP-80 User Manual 6.18 VLANconguration A Virtual LAN (VLAN) is a logical network gr ouping that limits the broadcast domain, which would allow y ou to isolate network trafc, so only the members of the sameVLAN will r eceive trafc fr om the ones of the same VLAN.
51 A T -IFS802SP-80 User Manual Pull do wn the selection item and f ocus on • P or t Based then press to set the VLAN Operation Mode in P or t Based mode . Click to add a ne w VLAN group (The maximum VLAN gr oups are up to 64). • VLAN – P or t Based interface A d d A p p l y Enter the gr oup name and VLAN ID .
52 A T -IFS802SP-80 User Manual VLAN—P or t Based Edit/Delete interface Use to delete the VLAN. • Use to modify gr oup name, VLAN ID , or add/remo ve the members of the existing • VLAN gr oup.
53 A T -IFS802SP-80 User Manual Pull down the selection item and f ocus on • 802.1Q then pr ess to set the VLAN Operation Mode in 802.1Q mode. Enable GVRP Protocol • : GVRP (GARP VLAN Registration Pr otocol) is a protocol that facilitates contr ol of vir tual local area netw orks (VLANs) within a larger network.
54 A T -IFS802SP-80 User Manual Hybrid Link : A segment which consists of Access and T runk links. The h ybrid por t has both the features of access and trunk por ts.
55 A T -IFS802SP-80 User Manual Gr oupCongurationinterface > Click . A p p l y 6.19 Rapid Spanning T r ee The Rapid Spanning T ree Pr otocol (RSTP) is an ev olution of the Spanning T ree Pr otocol and provides for faster spanning tree conv ergence after a topolog y change .
56 A T -IFS802SP-80 User Manual [note] Follo wtheruleasbelowtoconguretheMAX Age , Hello Time , andF orward Dela y Time.
57 A T -IFS802SP-80 User Manual RSTPP or tCongurationinterface 6.20SNMPConguration Simple Netw ork Management Pr otocol (SNMP) is the protocol de veloped to manage nodes (ser vers, workstations, r outers, switches and hubs etc .
58 A T -IFS802SP-80 User Manual Agent Mode • : Select the SNMP version that you want to use it. And then click to switch to the selected SNMP v ersion mode . C h a n g e SNMPSystemCongurationinterface A trap manager is a management station that receiv es the trap messages generated by the switch.
59 A T -IFS802SP-80 User Manual Congur etheSNMP V3function. Context T able Congur eSNMP v3context table . Assignthe contextname ofcontext table . Click toad d context name.
60 A T -IFS802SP-80 User Manual Access T able Congur eSNMPv3accesstable. ContextPr ex • : set up the context name . Gr oup Name • : set up the gr oup . Security Le vel • : select the access level. Context Match Rule • : select the context match rule .
61 A T -IFS802SP-80 User Manual Use a strict priority scheme : Alwa ysthehigherqueue willbeprocessedrst, exceptthe higher queue is empty . Priority T ype : There are 5 priority type selections available— P ort-based, T OS only , COS only , T OSrst , and COSrst .
62 A T -IFS802SP-80 User Manual Set up the COS priority level. With the dr op-down selection item of Priority T ype above being selected as COS only/COS rst, this contr ol item will then be a vailable to set the queuing policy for each port.
63 A T -IFS802SP-80 User Manual The switch suppor t IP multicast, you can enable IGMP protocol on web management’ s switch setting advanced page , then the IGMP snooping information displa ys. IP multicast addr esses range ar e from 224.0.0.0 thr ough 239.
64 A T -IFS802SP-80 User Manual Enable Ring • : T o enable the X-Ring function, tick the checkbox beside the Enable Ring string label. If this checkbox is not tick ed, all the ring functions are una vailable . Enable Ring Master : Tick the checkbox to enable this s witch to be the ring master .
65 A T -IFS802SP-80 User Manual 6.24LLDPConguration Link La yer Discovery Protocol (LLDP)is dened in the IEEE 802.1AB, itis an emerging standard which pr ovides a solution forthe conguration issues caused by expanding LANs.
66 A T -IFS802SP-80 User Manual 802.1xSystemCongurationinterface Y ou can congure the 802.1x authentication state for each por t. The state pr ovides Disable , Accept, Reject, and Authorize.
67 A T -IFS802SP-80 User Manual Quiet P eriod: • Set the period which the port doesn’ t tr y to acquir e a supplicant. TX P eriod • : Set the period por t waits for retransmit next EAPOL PDU during an authentication session.
68 A T -IFS802SP-80 User Manual Add the Static MA C Addr ess Y oucanaddstaticMA Caddr essintheswitchMA Ctablehere. MA C Addr ess • : Enter the MA C address of the por t that should permanently forward trafc , regar dless of the device netw ork activity .
69 A T -IFS802SP-80 User Manual MA C Address • : EntertheMA Caddressthaty ouwanttolter . Click . • Ify ouwant todeletethe MA Caddr essfr omthe lteringtable, select theMA Caddr essand • click .
70 A T -IFS802SP-80 User Manual Multicast Filtering interface.
71 A T -IFS802SP-80 User Manual 6.27 F actor y Default Resetswitchtodefaultconguration. Clicktoresetallcongurationstothedefaultvalue. D e f a u l t Factor y Default interface 6.
72 A T -IFS802SP-80 User Manual T r oubles shootin g V erify that is using the right pow er cord/adapter (DC 24-48V), please don’ t use the pow er adapter • with DC output higher than 48V , or it ma y damage this device. Select the proper UTP/STP cable to construct the user netw ork.
73 A T -IFS802SP-80 User Manual Appendix A—RJ-45 P in Assignment RJ-45 Pin Assignments The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX connections), • or Gigabit Ethernet (10Base-T/100Base-TX/1000Base-T connections).
74 A T -IFS802SP-80 User Manual 10/100Base-TX Cable Schematic • Thefollowingtw oguressho wthe10/100Base-TXcableschematic . Straight-thr ough cable schematic Cr oss over cable schematic 10/100/1000Base-TX Pin outs • Thefollowinggur eshowsthe10/100/1000EthernetRJ-45pinouts.
75 A T -IFS802SP-80 User Manual 10/100/1000Base-TX Cable Schematic • Straight thr ough cables schematic Cr oss over cables schematic.
76 A T -IFS802SP-80 User Manual Appendix B—Command Sets Commands Set List User EXEC Privileged EXEC Globalconguration VLAN database Interfaceconguration E P G V.
77 A T -IFS802SP-80 User Manual admin passw ord [Passw ord] G Speciesapassw ord (maximum 10 w ords) switch(cong)#adminpassw ordxxxxxx show admin P Show administrator information s.
78 A T -IFS802SP-80 User Manual P or t Commands Set Netstar Commands Le vel Description Example interface fastEthernet [P or tid] G Choose the port for modication. switch(cong)#interfacefastEthernet2 duplex [full | half] I Use the duplex congurationcommandto specify the duplex mode of operation for Fast Ethernet.
79 A T -IFS802SP-80 User Manual bandwidth out [V alue] Set interface output bandwidth. Rate Range is fr om 100 kbps to 102400 kbps or to 256000 kbps for giga ports and zero means no limit.
80 A T -IFS802SP-80 User Manual T runk Commands Set Netstar Commands Le vel Description Example aggr egator priority [1~65535] G Set port group system priority switch(cong)#aggr egatorpriority.
81 A T -IFS802SP-80 User Manual VLAN Commands Set Netstar Commands Le vel Description Example vlan database P Enter VLANconguremode s witch#vlan database Vlanmode [portbase| 802.1q | gvrp] V T o set switch VLAN mode . switch(vlan)#vlanmode portbase or switch(vlan)#vlanmode 802.
82 A T -IFS802SP-80 User Manual vlan 8021q trunk [P or tNumber] access-link untag [UntaggedVID] V Assign a access link for VLAN by trunk gr oup switch(vlan)#vlan 8021q trunk 3 access- link untag 33 vl.
83 A T -IFS802SP-80 User Manual Spanning T ree Commands Set Netstar Commands Le vel Description Example spanning-tree enable G Enable spanning tr ee switch(cong)#spanning-tr eeenable spanning-tr.
84 A T -IFS802SP-80 User Manual stp-path-priority [P or t Priority] I Use the spanning-tr ee port-priority interface congurationcommandto congur eaportpriority that is used when tw o switches tie for position as the r oot switch.
85 A T -IFS802SP-80 User Manual Commands Set Netstar Commands Lev el Description Example qos policy [weighted-fair|strict] G Select QOS policy scheduling switch(cong)#qospolicyw eighted- fair.
86 A T -IFS802SP-80 User Manual IGMP Commands Set Netstar Commands Le vel Description Example igmp enable G Enable IGMP snooping function switch(cong)#igmpenable Igmp-quer y auto G Set IGMP quer.
87 A T -IFS802SP-80 User Manual Mac / Filter T able Commands Set Netstar Commands Le vel Description Example mac-addr ess-table static hwaddr [MA C] I Congur eMA Caddr ess table of interface (static).
88 A T -IFS802SP-80 User Manual SNMP Commands Set Netstar Commands Le vel Description Example snmp system-name [System Name] G Set SNMP agent system name switch(cong)#snmpsystem-namel2switch .
89 A T -IFS802SP-80 User Manual snmpv3 mibview vie w [View Name] type [Excluded|Included] sub-oid [OID] G Congur ethemibviewtable of SNMPV3 agent switch(cong)#snmpv3mibvie wview V1 type Excluded sub-oid 1.
90 A T -IFS802SP-80 User Manual P or t Mirr oring Commands Set Netstar Commands Le vel Description Example monitor [RX|TX|Both] I Congur esour cepor tof monitor function switch(cong).
91 A T -IFS802SP-80 User Manual 802.1x Commands Set Netstar Commands Le vel Description Example 8021x enable G Use the 802.1x global congurationcommandto enable 802.1x pr otocols. switch(cong)#8021xenable 8021x system radiusip [IP addr ess] G Use the 802.
92 A T -IFS802SP-80 User Manual 8021x misc maxrequest [n umber] G Use the 802.1x misc max requestglobalconguration command to set the MAX requests. switch(cong)#8021xmiscmaxr equest3 8021x misc reauthperiod [sec.] G Use the 802.
93 A T -IFS802SP-80 User Manual TFTP Commands Set Netstar Commands Le vel Description Example backup ash:backup_cfg G Sa vecongurationto TFTP and need to specify the IP of TFTPser v erandthele name of image.
94 A T -IFS802SP-80 User Manual SystemLo g, SMTP and Ev ent Commands Set Netstar Commands Lev el Description Example systemlog ip [IP addr ess] G Set System log ser ver IP addr ess.
95 A T -IFS802SP-80 User Manual no ev ent authentication- failure G Disable Authentication failure e vent typ switch(cong)#noe ventauthentication- failure no ev ent ring-topolog y- change G D.
96 A T -IFS802SP-80 User Manual SNTP Commands Set Netstar Commands Lev el Description Example sntp enable G Enable SNTP function switch(cong)#sntpenable sntp da ylight G Enable da ylight sa ving time , if SNTP function is inactiv e, this command can’ t be applied.
97 A T -IFS802SP-80 User Manual X-ring Commands Set Netstar Commands Lev el Description Example ring enable G Enable X-ring switch(cong)#ringenable ring master G Enable ring master switch(con.
Een belangrijk punt na aankoop van elk apparaat Allied Telesis AT-IFS802SP (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Allied Telesis AT-IFS802SP heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Allied Telesis AT-IFS802SP vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Allied Telesis AT-IFS802SP leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Allied Telesis AT-IFS802SP krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Allied Telesis AT-IFS802SP bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Allied Telesis AT-IFS802SP kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Allied Telesis AT-IFS802SP . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
