Gebruiksaanwijzing /service van het product 2230 van de fabrikant Firestone
Ga naar pagina of 20
.
TABLE OF CONTENTS W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i LIMIT A TION OF LIABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C C ongratulations on your purchase of a new IntelliRide system by Firestone. This kit will provide automatic height control and leveling of your vehicle. The following will introduce you to the system components as well as provide detailed instructions concerning installing the height sensors and programming the system.
Battery Connection Connections to be made with vehicle interior Program button. This is discon- nected after programming and replaced with the Park Wire. Connector to ECU, to be mounted inside the vehicle. Service Switch to be used to turn the system on and off.
1 IntelliRide ™ Full System Schematic DET DESCRIPTION 1 FULL SYSTEM V AL VE ASSEMBL Y 2 AIR COMPRESSOR 3 AIR T ANK - 3 GALLON 4 ELECTRIC CONTROL UNIT (ECU) 5 HEIGHT SENSORS 6 1/4 TUBING 18ft.
SYSTEM COMPONENTS Wire Harness All necessary electrical wires and connectors have been included with this kit. Review Figure 1 before beginning installation. Y ou will have to put the major components in a position so that the wire harness will reach all of them.
SYSTEM COMPONENTS (cont.) Height Sensors The height sensor connections must go to their corresponding corners for proper sensor operation. THE HEIGHT SENSORS AND THE WIRE HARNESS CONNECTIONS ARE LOCA TION AND POSITION SENSITIVE .
SYSTEM COMPONENTS (cont.) Air Dryer Select a location to mount the air dryer . This should be a protected location to prevent damage from flying rocks or debris and close to the valve block. Ensure that a clear access to all of the fittings on the air dryer is maintained.
5 HEIGHT SENSOR INSTALLATION Step 1 There will be a bag in your kit with all of the hardware that you will need to put the height sensors on your vehicle. Group a height sensor from the kit with a height sensor bracket and two M5 x 8mm machine screws as indicated in Figure 2.
6 HEIGHT SENSOR INSTALLATION (cont.) Step 4 T o install the height control sensor , refer to Figure 4a, 4b and 5, to become familiar with the mounting geometry and hardware. Be sure that the area above and below the sensor location on the axle is clear of obstructions for the arm to move.
HEIGHT SENSOR INSTALLATION (cont.) Step 6 Once the sensor positions have been found, mark the locations of the mounting holes on the vehicle frame using the holes in the height sensor bracket as a template, refer to Figure 3 and Figure 5. Use a center punch to mark the center of the holes on the mounting surface.
8 PROGRAMMING THE SYSTEM For the system to oper ate properly the vehicle suspension tr av el will need to be programmed into the ECU. Reconnect the negative terminal on the battery . Step 1: Programming Setup Plug the program switch into the wire harness that is labeled program switch.
OPERATION OF THE SYSTEM Once height programming has been completed, the system is ready for use. The height selection switch is how you will be able to select your height. The switch has two green lenses with arrows printed on them. This is the primary user interface of the air leveling system.
COMMONLY ASKED QUESTIONS What is the lifetime expectancy of the Firestone dryer? If there are no system leaks it should be for good for system life. What type of accuracy is available with our system? The height sensors that we use are capable of an accuracy of 0.
COMMONLY ASKED QUESTIONS ( cont. ) In the WR8-760-2230 system, which port from valve block goes to & from the dryer? Each port on the valve block is labeled for the designated connector . Using the air line tubing, measure the distance from each port of the dryer back to the valve block.
TROUBLESHOOTING The height change works, but the WR8-760-2230 system will not level. The left-rear corner is exhausted fully . The LED height display shows the current he ight . The right-front valve is switched with the left-rear valve. Correct the air line connection with the corresponding air spring location and the solenoid valve connection.
TROUBLESHOOTING ( cont. ) The diagnostic lights on the WR8-760-2230 aftermarket IntelliRide system toggle fast as though it is attempting to change heights, and the valve block clicks trying to pass air . However no height change occurs and there is no air pressure within the reser voir tank.
For the latest technical information and support questions/answers, please visit: www .fsip.com/ir 14.
TECHNICAL 15.
Firestone Industrial Products Company 12650 Hamilton Crossing Blvd. Carmel, IN 46032-5400 www .fsip.com/Intelliride.
Een belangrijk punt na aankoop van elk apparaat Firestone 2230 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Firestone 2230 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Firestone 2230 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Firestone 2230 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Firestone 2230 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Firestone 2230 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Firestone 2230 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Firestone 2230 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
