Gebruiksaanwijzing /service van het product 58064 van de fabrikant Ford
Ga naar pagina of 23
MODEL 58064 owner ’ s manual.
2 • RAPTOR 3 BEFORE YOU PROCEED 3 SAFETY PRECAUTIONS 5 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT 6 ANATOMY OF THE RAPTOR 7 QUICK START: GETTING UP TO SPEED 8 TRAXXAS TQ 2.
RAPTOR • 3 BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and examine the model carefully.
4 • RAPTOR This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model.
RAPTOR • 5 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. For more information on batteries, see Use the Right Batteries on page 11.
6 • RAPTOR ANATOMY OF THE RAPTOR Motor Spur Gear Pinion Gear Slipper Clutch Electronic Speed Control Battery Compartment LED Light Pipe Battery Hold-Down Receiver Box Antenna Mount Front Suspension .
RAPTOR • 7 QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on pages 3-4 7.
8 • RAPTOR TRAXXAS TQ 2.4GHz RADIO SYSTEM Applying the Decals The main decals for your model have been applied at the factory. Additional decals have been printed on self- adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing.
RAPTOR • 9 Thermal Shutdown Protection - Temperature sensing electronics are used in the ESC to detect overloading and overheating of the transistor circuitry. If excessive temperature is detected, the unit automatically shuts down to prevent damage to the electronics.
10 • RAPTOR XL-5 Wiring Diagram TRAXXAS TQ 2.4GHz RADIO SYSTEM MODEL WIRING DIAGRAM Traxxas High-Current Connector (Male) to Battery To Motor LED Set Button Heat Sinks XL-5 ELECTRONIC SPEED CONTROL .
RAPTOR • 11 INSTALLING TRANSMITTER BATTERIES Your TQ 2.4GHz transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. 1. Remove the battery compartment door by pressing the tab and lifting the door up. 2. Install the batteries in the correct orientation, as indicated in the battery compartment.
12 • RAPTOR 5 The following Traxxas High- Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector.
RAPTOR • 13 Remember, always turn the transmitter on first and off last to avoid damage to your model. When rechargeable batteries begin to lose their charge, they will fade much faster than alkaline dry cells. Stop immediately at the first sign of weak batteries.
14 • RAPTOR USING THE RADIO SYSTEM The TQ 2.4GHz Radio System has been adjusted at the factory for correct operation with your model. The adjustment should be checked before running the model in case of movement during shipping. Here’s how: 1. Turn the transmitter switch on.
RAPTOR • 15 their model at distances farther than a football field (300+ feet). At greater distances, you could lose sight of your model and you may also exceed the radio system’s operating range which will cause the fail-safe system to activate.
16 • RAPTOR ADJUSTING THE ELECTRONIC SPEED CONTROL The XL-5 electronic speed control is equipped with built-in Low-Voltage Detection. The Low-Voltage Detection circuitry constantly monitors the battery voltage.
RAPTOR • 17 ADJUSTING THE ELECTRONIC SPEED CONTROL 8. The XL-5 is equipped with thermal shutdown protection to guard against overheating caused by excessive current flow. If the operating temperature exceeds safe limits, the XL-5 will automatically shut down.
18 • RAPTOR DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs.
RAPTOR • 19 2. The wheels have small holes molded in to allow air to enter and exit the tire during normal running. Water will enter these holes and get trapped inside the tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire.
20 • RAPTOR ADJUSTING YOUR MODEL Once you become familiar with driving your model, you might need to make adjustments for better driving performance Adjusting the Toe-in Geometry and alignment specs play an important roll in your model’s handling.
RAPTOR • 21 ADJUSTING YOUR MODEL Adjusting the Slipper Clutch The model is equipped with an adjustable slipper clutch, which is built into the large spur gear. The purpose of the slipper clutch is to regulate the amount of power sent to the rear wheels to prevent tire spin.
22 • RAPTOR Always wear eye protection when using compressed air or spray cleaners and lubricants. MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously.
121205 58064OM-N-EN-R00 MODEL 58064 1100 Klein Road, Plano Texas 75074 1-888-TRAXXAS owner ’ s manual.
Een belangrijk punt na aankoop van elk apparaat Ford 58064 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 58064 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 58064 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 58064 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 58064 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 58064 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 58064 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 58064 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
