Gebruiksaanwijzing /service van het product FX560 van de fabrikant FrancisFrancis
Ga naar pagina of 30
User Instruction & Installation Manual FX560 Remote Control 2 Kilowatt Xenon Searchlight Product Reference Number: A2471 – Variable Speed Motor Unit 240v A2473 – Variable Speed Motor Unit 115v.
CONTENTS 1 - Introduction 2 - Safety Precautions 3 - Technical Information 4 - Unpacking and Installation Instructions 5 - Electrical Installation 6 - Operating Instructions 7 - Fault Finding 8 - Main.
1 - Introduction It is imperative that this manual is read carefully and understood before installing your equipment. For your future reference please keep this manual in a safe place. Thank you for specifying a product from the Franc is Searchlights range.
2 - Safety Precautions The following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user. Note: When unpacking or manoeuvring the search light into its fixi ng position, suitable lifting points must be used in order to prevent damage to the equipment or personal injury.
3 - Technical Information This product has been designed to operate in acco rdance with the product specification. The FX560RC 2000 watt searchlight has the following features: All marine grade ma.
Power Supply Details (Model 8502) General Description Output Power 1400-2200 watts Voltage 22-30 volts D.C. Current 50-85 amperes D.C. Ripple 5% peak-to-peak Input Current 25/22 amperes maximum 40 amperes maximum Voltage 208/237 VAC 110/120 VAC Phase Single Frequency 60 Hz (50Hz available) Output Adjustments 9 steps Size Width 12” (30.
Caution Do not allow anything to be placed upon the pow er supply case; the perf orated top is for ventilation and must not be obstructed. Try to select a location as close to the lamphouse as practical. Many users install the power supply adjacent to the searchlight where spac e is available and local codes permit.
Warning The power supplies have two sources of power. Disconnect (turn off) primary power before making adjustments or service procedures. Output power adjustment Warning The power supply stores energy after primary power is switched off. Wa it a minimum of two minutes for the capacitor charge to bleed off.
Xenon lamp power supplies have two stages of operation: 1) Before igniting the bulb – At this time, t he voltage at the power supply output terminals reaches “open circuit” value (110 VDC or greater).
Low capacity or an open capacitor affect ignition because there is insufficient surge current to reliably light the bulb. If disconnecting a capacitor does change either flicker or ignition, then the capacitor is functioning. Reconnect it. High ripple current caused by a diode failure will result in overheating of R3.
Back To Top.
4 - Unpacking and Installation Instructions The following instructions should be read and full y understood prior to installing the equipment to ensure that the correct proc edures are followed and all safe ty precautions are observed.
5 - Electrical Installation For safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards.
Installation Guidelines A typical installation and connection routine for t he searchlight with a Variable Speed Gearbox is as follows: Referring to wiring diagram C22801, a supply is fed to the Control Panel, which then provides a common feed to the Motor Gearbox, Power Suppl y Unit and the Searchlight Control Panel.
Fitting instructions for the 2Kw xenon lamp Referring to the diagram overleaf: 1) Unfasten the ten latches (A) on the front and rear of the searchlight; 2) Remove the front bezel (B) and rear bezel (C.
Back To Top.
6 - Operating Instructions This equipment is designed for use out of doors, in free air. Never place anything on, or cover, the searchlight when in use as this may present a hazard. All PSU should be housed below deck/in doors. Never leave the PSU exposed to weather conditions.
Setting to Work Safe service in use necessitates the stri ct observance of the following precautions. Any article fabricated from quartz or gl ass is inherently fragile and care should therefore be taken, at all times, when handling lamps; Eye protection must be worn when handling lamps that have been removed from their packaging materials.
Notes : 1) XBO lamps are designed for dc operation only. The dc current may only be varied within the limits of the current control range. An XBO lamp operates best at rated current; over the life of the lamp, the current may be increased to its ma ximum value to compensate for loss of light.
7- Fault Finding All fault finding must be conducted by a competent person or qualified Electrical Engineer. Please refer to the following table fo r the trouble-shooting of Xenon lamps.
Failure of Lamp to Ignite In the event of the xenon lamp failing to light the following steps should be taken: 1) Check that the mains supply is connected to the input of the PSU.
8 - Maintenance and Servicing In order to prolong the service life and performance of your searchlight, the following maintenance guidelines are recommended: Maintenance checks should be conducted.
9 – General Assembly & Wiring Diagrams Drawing Number Description A2471/A2473 FX560RC 2Kw variable speed G.A. C22801 2Kw Xenon RC Wiring Diagram variable speed Control Panel Outline Drawing vari.
.
.
.
.
.
Back To Top.
10 - Spare Parts List The following spare parts can be order ed directly from the manufacturer: Part Number Description C15392-00 Power Supply Unit (240v) C21905-00 Power Supply Unit (115v) C12081-00 .
Een belangrijk punt na aankoop van elk apparaat FrancisFrancis FX560 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen FrancisFrancis FX560 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens FrancisFrancis FX560 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding FrancisFrancis FX560 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over FrancisFrancis FX560 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van FrancisFrancis FX560 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de FrancisFrancis FX560 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met FrancisFrancis FX560 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
