Gebruiksaanwijzing /service van het product SINBAD II van de fabrikant Frymaster
Ga naar pagina of 17
Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 819-5874 24-Hour Service Hotline 1-800-551-8633 MARCH 2005 SinBaD Installation a.
DANGER IMPROPER INSTALLATION, ADJUSTM ENT, ALTERATION, SERVICE, OR MAINTENANCE CAN CAUSE PROP ERTY DAMAGE, INJURY, OR DEATH. READ THE INSTALLATION, OPERATING, AND SERVICE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
SinBaD II SINGLE BASKET DISPENSER TABLE OF CONTENTS i CHAPTER 1: General Information 1.1 Parts Ordering and Service Information ..................................................................................... .... 1-1 1.2 Safety Information .....
SinBaD II SINGLE BASKET DISPENSER CHAPTER 1: GENERAL INFORMATION 1-1 1.1 Parts Ordering and Service Information In order to assist you as quickly as possible, the Frymaster Factory Authorized Service Center (FASC) or Service Department representative requires certain specific information about your equipment.
1-2 1.3 Equipment Description The SinBaD II Single Basket Dispenser is designed to dispen se french fries in batches of consistent weight into standard fryer baskets. The SinBaD II is a follow-on version of the original SinBaD design. It is identical to the original unit in operation but has a smaller cabinet.
1-3 A list of Factory Authorized Service Centers (FASCs ) is included with your unit when shipped from the factory. Failure to use qualified service personnel will void the warranty on your equipment. 1.6 Shipping Damage Claim Procedure Your equipment was carefully inspected and packed befo re leaving the factory.
SinBaD II SINGLE BASKET DISPENSER CHAPTER 2: INSTALLATION AND OPERATION 2-1 FINDING YOUR WAY AROUND YOUR NEW SinBaD UNIT Load Cell Arm s (behind front face of Dis pense Chute) Lid Sight G lass Crumb Pan and Basket Locator R ack Shown Remov ed fr om Unit.
2-2 2.1 Installation DANGER All electrically operated appliances must be electrically grounded in accordance w ith local codes, or in the absence of local codes, w ith the applicable national electrical code.
2-3 2.3 Operation CAUTION Ensure the ON/OFF Rocker Sw itch is in the OFF position before installing the hopper. 1. Verify that the ON/OFF Rocker Switch is in the “OFF” position. 2. Verify that the crumb pan is properly inserted in the deck cutout.
2-4 The indicator light in the selector will illuminate and the drum will begin to rotate, transferring fries from the hopper to the dispensing chute. When the prescribed weight has been transferred, drum rotation will cease. 12. Insert an empty basket all the way to the rear of the dispensing cham ber.
2-5 NOTE: If you do not begin pressing Selector 1 within 5 seconds after entering the PROGRAMMING mode, the unit will automatically return to the STANDBY mode. If you press a BATCH WEIGHT se- lector other than 1, the unit will return to the STANDBY mode immediately after the selector is pressed .
SinBaD II SINGLE BASKET DISPENSER CHAPTER 3: MAINTENANCE & OPERATOR TROUBLESHOOTING 3-1 3.1 Cleaning and Maintenance Routine cleaning in accordance with the following steps is the only operator maintenance required for your SinBaD unit. 1. Put the unit in STANDBY mode.
3-2 PROBLEM Probable Causes Corrective Action A. ON/OFF rocker switch is in OFF position. A. Place rocker switch in the ON position. B. Unit is not plugged in. B. Plug unit in. C. Main circuit breaker is tripped. C. Reset circuit breaker. UNIT WILL NOT POWER UP or NOTHING HAPPENS WHEN “RUN” MODE IS SELECTED.
3-3 PROBLEM Probable Causes Corrective Action Continued from previous page. B2. The minimum weight that should be programmed is .38 lbs. (.17kg). If a weight less than .38 lbs. (.17kg) has been programmed and selected, the unit will dispense batches of erratic weights.
3-4 PROBLEM Probable Causes Corrective Action A. Operator error. A. Batch weight selector “1” must be pressed four consecutive times within 5 seconds after the PROGRAM Switch is pressed. If more time is taken, or if a selector other than “1” is pressed, the unit automatically returns to the STANDBY mode.
THIS PAGE INTENTIONALLY LEFT BLANK.
Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000 Shipping Address : 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-318-219-7140 (Tech Support) 1-318-219-7135 Price: $4.
Een belangrijk punt na aankoop van elk apparaat Frymaster SINBAD II (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Frymaster SINBAD II heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Frymaster SINBAD II vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Frymaster SINBAD II leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Frymaster SINBAD II krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Frymaster SINBAD II bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Frymaster SINBAD II kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Frymaster SINBAD II . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
