Gebruiksaanwijzing /service van het product AOU9CQ van de fabrikant Fujitsu
Ga naar pagina of 18
A S U 9 C Q A S U 1 2 C Q A O U 9 C Q A O U 1 2 C Q.
En-2 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 AIR CLEANER RESET / MANUAL AUTO button ● Intake grill opening mechanism. When the remote control is not available for use, this button can be used as a Quick-start button. However when the Air Cleaning check function (see page 13) is in operation, this button is used as a reset button.
En-3 FEA TURES AND FUNCTIONS SLEEP TIMER When SLEEP is selected be pressing TIMER button during Heating mode, the air conditioner’ s thermostat setting is gradually lowered during the period of operation; during Cooling or Dry mode, the thermostat setting is gradually raised during the period of operation.
En-4 PREP ARA TION CAUTION! ● T ake care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit.
En-5 T o Select Mode Operation 1 Press the ST ART / STOP button (Fig.6 M ). The indoor unit’ s OPERA TION indicator lamp (red) (Fig. 3 5 ) will light. The air conditioner will start operating. 2 Press the MASTER CONTROL button (Fig.6 H ) to se- lect the desired mode.
En-6 OPERA TION About Mode Operation AUTO: ● Depending on the room temperature at the time operation begins, the operating mode will be switched automatically as shown in the accompanying table. Also, depending on the operating mode, the room temperature set- ting will cause the “standard” temperature to be set as shown.
En-7 AIR CLEANING OPERA TION 2 Press the AIR CLEAN button (Fig. 6 N ). The AIR CLEAN indicator lamp (Fig. 3 7 ) will light up (green, as shown in the figure). ● Air conditioning and Air Cleaning will function simultaneously. Air cleaning ● During operation, the unit produces a small amount of ozone that can be smelled.
En-8 TIMER OPERA TION T o Use the ON timer or OFF timer 1 Press the ST ART / STOP button (Fig. 6 M ). (if the unit is already operating, proceed to step 2). The indoor unit's OPERA TION Indicator Lamp (red) (Fig. 3 5 ) will light. 2 Press the TIMER button (Fig.
En-9 SLEEP TIMER OPERA TION Unlike other timer functions; the SLEEP timer is used to set the length of time until air conditioner operation is stopped. T o Use the SLEEP T imer 1 While the air conditioner is operating or stopped, press the TIMER button (Fig.
En-10 ADJUSTING THE DIRECTION OF AIR CIRCULA TION V ertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’ s SET button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers.
En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select SWING Operation Press the SWING button (Fig. 6 P ). The SWING indicator lamp (orange) (Fig. 3 8 ) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down.
En-12 Before cleaning the plasma filter unit, be sure to turn off the power supply to the air conditioner. Electric shock may result. ● When used for extended periods, the unit may accumulate dirt inside, reducing its performance. W e recommend that the unit be inspected regularly, in addition to your own cleaning and care.
En-13 CLEANING THE PLASMA AIR CLEANING FIL TER CAUTION! W ARNING! ● Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks on it. If the unit is not properly mounted, it could fall off and cause damage or injury.
En-14 5. Install the air filter. ● Please consult instructions for cleaning the air filter on page 12. 6. Close the intake grille. Push the intake grill in at 4 points (the two ends of its lower side as well as two center points of the lower side, as shown in the figure) to close it.
En-15 Air -cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting unit, please also take care of the filter. (Please carry out maintenance on the filter every 6 months.) 1. Open the intake grille and remove the air filter from the right side.
En-16 TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the Power Supply Plug, and consult authorized service personnel. Merely turning off the unit’ s power switch will not completely disconnect the unit from the power source.
En-17 TROUBLESHOOTING Symptom Doesn’ t operate at all: Poor Cooling or Heating performance: The unit operates differently from the Remote Control Unit’ s setting: See Page — 8 - 9 — 5 4 CHECK .
En-18 OPERA TING TIPS Outdoor temperature Indoor temperature Cooling/Dry Mode About 32 to 115 °F About 64 to 90 °F T emperature and Humidity Range If the unit is used for long periods under high-humidity conditions, condensation may form on the surface of the indoor unit, and drip onto the floor or other objects underneath.
Een belangrijk punt na aankoop van elk apparaat Fujitsu AOU9CQ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fujitsu AOU9CQ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fujitsu AOU9CQ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fujitsu AOU9CQ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fujitsu AOU9CQ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fujitsu AOU9CQ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fujitsu AOU9CQ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fujitsu AOU9CQ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
