Gebruiksaanwijzing /service van het product MT110-101 van de fabrikant Altinex
Ga naar pagina of 26
MULTITASKER ™ MANUAL PAR T NUMBER: 400 - 0197 - 005 8 X 8 MONO AUDIO MATRIX SWITCHER CARD FOR MULTITASKER ™ USER’S GUIDE MT110 - 101/103.
MULTITASKER ™ 400 - 0197 - 005 1 1 TA BLE OF CONTENTS Page PRECAUTIONS / SAFETY WA RNINGS ............... 2 GENERAL .......................................................... 2 INSTALLATION ................................................. 2 CLEANING .
MULTITASKER ™ 400 - 0197 - 005 2 2 PRECA UTIONS / SA FETY WA RNINGS 1 Please read this manual carefully before using you r MT110 - 101/103 . Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MT110 - 101/103 and to prevent fire and shock hazard.
MULTITASKER ™ 400 - 0197 - 005 3 3 AB OUT YOUR MT110 - 101/103 2 The MT110 - 101/103 is a Balanced Audio Matr ix Switching Card. This card allows any input to be independently switched to any of the outputs. All inputs and outputs can be wired for unbalanced audio, or balanced audio allowing longer cable runs and superior noise resistance.
MULTITASKER ™ 400 - 0197 - 005 4 4 DESCRIPTION OF MT110 - 101/103 4.
MULTITASKER ™ 400 - 0197 - 005 5 5 AP PLICA TION DIA GRA M 5 Diagram 1 : Typical Setup.
MULTITASKER ™ 400 - 0197 - 005 6 6 Diagram 2 : MT110 - 103 Internal View.
MULTITASKER ™ 400 - 0197 - 005 7 7 Diagram 3 : MT110 - 101 Internal View.
MULTITASKER ™ 400 - 0197 - 005 8 8 INSTA LLING YOUR MT110 - 101/103 6 Step 1. Turn off power to the MultiTasker™ enclosure. Step 2. Slide the MT110 - 101/103 into an available slot in the MultiTasker™ Basic Enclosure in order to connect to the bus.
MULTITASKER ™ 400 - 0197 - 005 9 9 The Card ID is a unique identifier. It is equal to the enclosure slot number, or it may be an assigned value. As the slot number, the value can range from 1 to 4 up to 1 to 20 depending on the enclosure. If the value is assigned, the ID may be a maximum of 99.
MULTITASKER ™ 400 - 0197 - 005 10 10 Example: If Input 1 is connected to all outputs, but only 1 through 4 are on, the feedback after sending the command [C4S], for slot 4, would be similar to the f.
MULTITASKER ™ 400 - 0197 - 005 11 11 The matrix I/O connections are also read left to right representing outputs 1-8 and the input to which each is connected. The first two digits show the input num ber to which Output 1 is connected. The third and forth digits are for Output 2 and so on.
MULTITASKER ™ 400 - 0197 - 005 12 12 PATH OPERATION The path for outputs on the same or multiple cards may be preloaded. This will set the path for the output, but it is not active until the switch command, [SW ], is executed. Commands en ding in ‘P’ are not executed immediately.
MULTITASKER ™ 400 - 0197 - 005 13 13 If ‘F’ is included, use the [OFFmCnPF] command or the [OFFmCnFP] command. FEEDBACK OPERATION After processing a command, an “OK” or “[ERR001]” will be returned as feedback if ‘F’ is included at the end of a command string.
MULTITASKER ™ 400 - 0197 - 005 14 14 Command Format: [ImO * CnUi] m = Input (m = # from 1 to 8) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Connect Input 1 to all outputs for the MT110 - 10 3 in slot 5. Send the command [I1O*C5] and Input 1 will be con nected to all outputs.
MULTITASKER ™ 400 - 0197 - 005 15 15 ID COMMANDS: RSI, SIDn, SIDnCi, SID+, RSN The default Card ID is the same as the card slot number. The next several commands allow the user to change the Card ID to a value other than the slot number. Once the ID is changed, moving the card to ano ther slot will not change the card ID.
MULTITASKER ™ 400 - 0197 - 005 16 16 23. [SID+] This co mmand sets the Card ID of all cards to their slot number plus the offset value. Command Format: [ SID+n ] n = Offset amount (n = # from 0 to 99) The maximum Card ID is 99, so subtract the highest slot number from 99 to find the maximum offset.
MULTITASKER ™ 400 - 0197 - 005 17 17 Command Format: [RMCn 1 Cn 2 …GkUi] Cn = Card ID (n= # from 1 to max slots) Gk = Group ID (k = # from 1 - 8) Ui = Unit ID (i = # from 0 - 9) Example: Group 5 consists of the cards located in slots numbered 2 , 4 , and 6 .
MULTITASKER ™ 400 - 0197 - 005 18 18 Command Format: [VLOmAvCnUi] m = Output (m = # from 1 to 8) v = Volume Level (v = # from 1 to 32) Cn = Card ID (n = # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: There is an MT110 - 10 3 card in slot 8.
MULTITASKER ™ 400 - 0197 - 005 19 19 34. [RUP] MT110 - 10 3 ONLY This command ramps the output volume to its maxim um level at the rate defined using the [RAMP] command.
MULTITASKER ™ 400 - 0197 - 005 20 20 rate defined using the [RAMP] command. The ramping may be stopped at any time using the [RST] command. Command Format: [RDNmCnUi] Cn = Card ID (n = # from 1 to max slots) m = Output No.
MULTITASKER ™ 400 - 0197 - 005 21 21 42. [RA MP=x] MT110 - 10 3 ONLY This command sets the ramp rate for 32 steps. The settings range from 4 to 18 seconds, in two - second intervals. Command Format: [RAMP=xCnUi] x = Rate in Seconds 4 = 0.13 seconds/step 6 = 0.
MULTITASKER ™ 400 - 0197 - 005 22 22 4 x 4 I NPUTS O UTPUTS 1 a 1 a 1 b 1 b 2 a 2 a 2 b 2 b 3 a 3 a 3 b 3 b 4 a 4 a 4 b 4 b 2 x 2 I NPUTS O UTPUTS 1 a 1 a 1 b 1 b 1 c 1 c 1 d 1 d 2 a 2 a 2 b 2 b 2 c 2 c 2 d 2 d 46. [HELP] This command displays information available for the MultiT asker™ interface commands.
MULTITASKER ™ 400 - 0197 - 005 23 23 32) [ + ] Increment volume 33) [ - ] Decrement volume 34) [RUP] Ramp UP to max (32) 35) [ RDN ] Ramp DOWN to mon (0) 36) [RUPm] Ramp volume UP to max (32) 37) [R.
MULTITASKER ™ 400 - 0197 - 005 24 24 Cause 2: The card and its serial device are not communicating. Solution 1: Turn the system off and then on again. If there is still an error, see Ca use 3. Cause 3: RS485 communication error Solution 1: Make sure that the card is pushed all the way into the slot.
MULTITASKER ™ 400 - 0197 - 005 25 25 AL TINEX POLICY 9 9.1 LIMITED WA RRA NTY/RETURN POLICY Please see the Altinex website at www.altinex.com for details on warranty and return polic ies .
Een belangrijk punt na aankoop van elk apparaat Altinex MT110-101 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Altinex MT110-101 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Altinex MT110-101 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Altinex MT110-101 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Altinex MT110-101 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Altinex MT110-101 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Altinex MT110-101 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Altinex MT110-101 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
