Gebruiksaanwijzing /service van het product GTP 59 van de fabrikant Garmin
Ga naar pagina of 188
190-01115-01 August, 2009 Revision A G3X Installation Manual.
Page A G3X Installation Manual Revision A 190-01115-01 © Copyright 2009 Garmin Ltd. or its subsidiaries All Rights Reserved Except as expressly provided herein, no part of this manual may be reproduc.
G3X Installation Manual Page i 190-01115-01 Revision A WARNING This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is being provided in accordance with California's Proposition 65.
Page ii G3X Installation Manual Revision A 190-01115-01 TABLE OF CONTENTS PARAGRAPH PAGE 1 G3X Installation Overview .................................................................................................... .......... 1-1 1.1 Unpacking Unit .
G3X Installation Manual Page iii 190-01115-01 Revision A PARAGRAPH PAGE 5 GTP 59 ....................................................................................................................... ...................... 5-1 5.1 Equipment Description.
Page iv G3X Installation Manual Revision A 190-01115-01 PARAGRAPH PAGE APPENDIX A: G3X Pinouts ....................................................................................................... ............ A-1 A.1 GDU 37X .......................
G3X Installation Manual Page v 190-01115-01 Revision A LIST OF ILLUSTRATIONS FIGURE PAGE 1-1 G3X Interconnect Example ................................................................................................... ........... 1-2 1-2 Coaxial Cable Installation .
Page vi G3X Installation Manu al Revision A 190-01115-01 FIGURE PAGE 6-26 Example Bracket Antenna Mounting Under Glareshield............................................................... 6-24 6-27 Example Non-structural Ante nna Mounting Under Glareshield .
G3X Installation Manual Page vii 190-01115-01 Revision A FIGURE PAGE B-17 Insulation/Contact Clearance .............................................................................................. ......... B-23 B-18 Daisy Chain Shield Termination ..
Page viii G3X Installation Manual Revision A 190-01115-01 LIST OF TABLES TABLE PAGE 1-1 G3X LRU Part Numbers ....................................................................................................... ........... 1-3 1-2 Contents of GDU 37X As sembly (010-00667-XX) .
G3X Installation Manual Page ix 190-01115-01 Revision A TABLE PAGE 6-4 XM Satellite Radio Antenn a Minimum Requirements .................................................................... 6-2 6-5 Teardrop Footprint Antenna Doubler Design and Installation .
Page x G3X Installation Manual Revision A 190-01115-01 Limited Warranty for Garmi n GMU 44 and GTP 59 Products The Garmin products GMU 44 and GTP 59 are warrant ed to be fr ee from defects in materials or workmanship for two years from the date of purchase.
G3X Installation Manual Page xi 190-01115-01 Revision A Limited Warranty for GSU 73 and GDU 37X Products The Garmin products GSU 73 and GDU 37X are warranted to be free from defects in materials or workmanship for one year from the date of purchase.
Page xii G3X Installation Manual Revision A 190-01115-01 GSU 73 HARDWARE MOD LEVE L HISTORY The following table identifies hardware modificati on (Mod) Levels for the GSU 73 LRU. Mod Levels are listed with the associated service bulletin numbe r, service bulletin date, and the purpose of the modification.
G3X Install ation Manual – I nstallati on Overview Page 1-1 190-01115-01 Revision A 1 G3X Installation Overview 1.1 Unpacking Unit Carefully unpack the equipment and make a visual in spection of the unit for evidence of damage incurred during shipment.
Page 1-2 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.3 System Overview The G3X is an advanced technology avionics suite desi gned to integrate pilot/aircraft interaction into one central system.
G3X Install ation Manual – I nstallation Overview Page 1-3 190-01115-01 Revision A 1.4 General G3X LRU Specifications 1.4.1 Garmin LRU Part Numbers Table 1-1.
Page 1-4 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.4.3 Physical Specifications All width, height, and depth m easurements are taken with unit rack (if applicable) and connectors.
G3X Install ation Manual – I nstallation Overview Page 1-5 190-01115-01 Revision A 1.5 Installation Requirements One GDU 37X assembly (listed in Table 1-1) is required, dependent upon cust omer’s desired database region. Each GDU 37X (010-00667-XX) comes with all equipment needed for installation.
Page 1-6 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.7.1 Wiring Harness Installation Allow adequate space for installation of cables and conn ectors. Ensure that routing of the wiring does not come in contact with sources of heat, RF or EMI in terference.
G3X Install ation Manual – I nstallation Overview Page 1-7 190-01115-01 Revision A 1.7.2 Cable Location Considerations Use cable meeting the applicable aviation regulation for the interconnect wiring. Any cable meeting specifications is acceptable for the installation.
Page 1-8 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.7.4 Backshell Assemblies Connector kits include backshell assemblies. The backshell assembly houses the configuration module and a thermocouple reference junction (if applicable, see Appendix D).
G3X Installat ion Man ual – G DU 37 X Page 2-1 190-01115-01 Revision A 2 GDU 37X Figure 2-1. GDU 37X Unit View 2.1 Equipment Description NOTE There is no TSO/ETSO applicable to the GDU G37X. The GDU 37X provides a central display and user interfa ce for the G3X system.
Page 2-2 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.1.2 Interface Summary The GDU 37X uses CAN and RS-232 communications in terfaces.
G3X Installat ion Man ual – G DU 37 X Page 2-3 190-01115-01 Revision A 2.2.4 Antennas Table 2-4 lists Garmin and non-Garmin antennas currently supported by the GDU 37X. Refer to Section 6 for Garmin antenna installation information. For non-Garm in antennas, follow the manufacturer’s installation instructions.
Page 2-4 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.4 Installation Requirements 2.4.1 Accessories The GDU 37X Connector Kit is provided with the G DU 37X unit and is required to install t he unit (Figure 2-2).
G3X Installat ion Man ual – G DU 37 X Page 2-5 190-01115-01 Revision A 2.5 Installation Considerations Fabrication of a wiring harness is required. Sound mechanical and electrical methods and practices are recommended for installation of the GDU 37X.
Page 2-6 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.9 Panel Cutout Template The below drawing can be used as a template when ma rking the panel for cutout. Dimensions below are to verify accuracy of printout only, see Figure C-1.2 for complete dimensions.
G3X Installat ion Man ual – G M U 44 Page 3-1 190-01115-01 Revision A 3. GMU 44 Figure 3-1. GMU 44 Unit View 3.1 Equipment Description The Garmin GMU 44 Magnetometer is a rem ote mounted device that interfaces with a Garmin GSU 73 to provide flight attitude and heading data for flight instrumentation.
Page 3-2 G3X Installation Manual – GMU 44 Revision A 190-01115-01 3.3 Environmental Specifications Table 3-2 lists general environmental specifications.
G3X Installat ion Man ual – G M U 44 Page 3-3 190-01115-01 Revision A 3.5 Installation Requirements 3.5.1 Equipment Available Table 3-5. GMU 44 Part N umbers Model Catalog Part Number Unit Part Number Installation Rack GMU 44 010-00296-10* 011-00870-10 No *Included in G3X LRU Kit (K10-00016-00) Table 3-6.
Page 3-4 G3X Installation Manual – GMU 44 Revision A 190-01115-01 Table 3-7. Required Distan ce from Mag netic Disturbances Disturbance Source Minimum Distance from GMU 44 Electric motors and relays, including servo motors 10 feet (3.
G3X Installat ion Man ual – G M U 44 Page 3-5 190-01115-01 Revision A 3.6.1 Consideration for Wing Grounded Lighting Fixtures The following installation practices are recommende d if the required GMU 44 mounting bracket is located in the wing.
Page 3-6 G3X Installation Manual – GMU 44 Revision A 190-01115-01 3.8 Mounting Instructions After evaluation of the mounting location has been completed and ensuring that requirements are met, assemble the GMU 44 mounting plate kits according to th e dimensions given in Appendix C.
G3X Installat ion Man ual – G SU 7 3 Page 4-1 190-01115-01 Revision A 4 GSU 73 4.1 Equipment Description NOTE There is no TSO/ETSO applicable to the GSU 73. The GSU 73 is intended for the LSA (light sport aircraft ) and experimental aircraft markets.
Page 4-2 G3X Installation Manual – GSU 73 Revision A 190-01115-01 4.1.1 Features Summary Air Data Interfaces Pressure Altitude CAN (1) Density Altitude RS-232 (2 TX/2 RX) Vertical Speed ARINC 429 (4.
G3X Installat ion Man ual – G SU 7 3 Page 4-3 190-01115-01 Revision A 4.3 Environmental Specifications The GSU 73 is a non-TSO’d product, Table 4-2 lists general environm ental specifications. NOTE The GSU 73 may require a warm-up pe riod of 15 minutes to reach full accuracy (30 minutes if the environmental temperature is less than 0°C).
Page 4-4 G3X Installation Manual – GSU 73 Revision A 190-01115-01 Table 4-5. Contents of P732 Connector Kit (011-01818-01)** Item Garmin P/N Quantity Sub-Assy,Backshell w/Hdw,Jackscrew 011-01855-04 .
G3X Installat ion Man ual – G SU 7 3 Page 4-5 190-01115-01 Revision A 4.5.1 Pneumatic Plumbing The GSU 73 has two ports that are connected to the aircraft’s pitot pressure source and static pressure source. The two ports are labeled on the unit (see Fi gure 4-2).
Page 4-6 G3X Installation Manual – GSU 73 Revision A 190-01115-01 4.6 Mounting Requirements Mount the GSU 73 with the connectors aligned within 1.0 deg of either the X or Y axis of the aircraft. The direction of the unit will be accounted for duri ng the calibration procedure as shown in Figure 4-3.
G3X Installat ion Man ual – G SU 7 3 Page 4-7 190-01115-01 Revision A Do not use shock mounting to m ount the GSU 73. Shoc k mounts used for other types of inertial systems are not acceptable for the GSU 73 AHRS. The mounti ng system must have no resonance with the unit installed.
Page 4-8 G3X Installation Manual – GSU 73 Revision A 190-01115-01 4.8 Maintenance Per Part 43 Appendix E, paragraph (b)(2), Garm in sp ecifies a test procedure equivalent to part 43 Appendix E, paragraph (b)(1) with two exceptions.
G3X Installation M anual – GTP 59 Page 5-1 190-01115-01 Revision A 5 GTP 59 Figure 5-1. GTP 59 5.1 Equipment Description The Garmin GTP 59 is an outside mounted tem perature probe that provides raw air temperature data. The temperature input device is a three-wire temperature probe interface.
Page 5-2 G3X Installation M anual – GTP 59 Revision A 190-01115-01 5.2.1 Additional Equipment Required • Cables - The installer will supply all system cables. 5.3 TSO/ETSO Compliance The following table provides a list of applicable TSO/ETSOs for the GTP 59.
G3X Installation M anual – GTP 59 Page 5-3 190-01115-01 Revision A 5.4 Installation Considerations 5.4.1 GTP 59 Icing The GTP 59 OAT probe has no icing protection. If ice accumulates on the GTP 59 OAT probe, its accuracy is unknown. Consequently, air temperature measurements may be incorrect if ice accumulates on the probe.
Page 5-4 G3X Installation M anual – GTP 59 Revision A 190-01115-01 5. Strip back 1/8” (0.125”) of insulation and crim p pins (11) to each of the conductors in the shielded cable. 6. Cut an AWG #16 (8) wire to 3” long. Strip back 0.5” of insulation from this cable.
G3X Installat ion Man ual – A nte nnas Page 6-1 190-01115-01 Revision A 6 Garmin GPS/XM Antennas For non-Garmin antennas, follow the manufacturer’s in stallation instructions. If using a Garmin GA 26C or GA 26XM, refer to the accompanying installati on instructions (190-00082- 00 or 190-00522-03).
Page 6-2 G3X Installation Manual – An tennas Revision A 190-01115-01 Table 6-4. XM Satellite Radio Antenna Minimum Requirements Characteristics Specifications Frequency Range 2332.5 to 2345 MHz Gain (Typical) 24 dB* Noise Figure <1.2 dB Nominal Output Impedance 50 ohms Supply Voltage 3.
G3X Installat ion Man ual – A nte nnas Page 6-3 190-01115-01 Revision A 6.3.2 GPS/XM Antenna Mounting Location The GPS antenna is a key element in the overall sy stem performance and integrity for a GPS navigation system. The mounting location, geometry, and surr oundings of the antenna can affect the system performance and/or availability.
Page 6-4 G3X Installation Manual – An tennas Revision A 190-01115-01 Figure 6-1 shows the recommended placement of antennas. 4 Figure 6-1. Recommended Antenna Placement.
G3X Installat ion Man ual – A nte nnas Page 6-5 190-01115-01 Revision A 6.3.3 Buried Antenna (below the skin covering or gl areshield) Mounting There are potential performance issues related to buried antennas that the kit builder/installer should be aware of prior to electing to install a buried antenna.
Page 6-6 G3X Installation Manual – An tennas Revision A 190-01115-01 Mounting the antenna under the glare shield (Figure 6- 3) is a good option for XM – FIS antennas, although it is not typically the best optio n for a GPS antenna. This location results in the aft fuselage shading the antenna.
G3X Installat ion Man ual – A nte nnas Page 6-7 190-01115-01 Revision A 6.4 Teardrop Footprint Antenna Insta llation (GA 55 and GA 56) This section describes the structural mounting of the teardrop footprint antenna installation.
Page 6-8 G3X Installation Manual – An tennas Revision A 190-01115-01 6.4.2 Antenna Installation Instructions 1. Refer to Table 6-5 and the drawings in Appe ndix C for gui dance on selecting the appropriate mounting cutout. Drill or punch t he holes to match the mating part (doubler).
G3X Installat ion Man ual – A nte nnas Page 6-9 190-01115-01 Revision A 6.4.3 Reference Figures Figure 6-4. Doubler Design, Teardrop Footprint Antenna, Skin Thickness 0.032" to 0.049" Figure 6-5. Doubler Design, Teardrop Footprint Antenna, Skin Thickness 0.
Page 6-10 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-6. Doubler Design, Teardrop Footprint Antenna, Skin Thickness 0.051" to 0.
G3X Installation Manual – Antennas Page 6-11 190-01115-01 Revision A Figure 6-8. Skin Cutout Detail, Teardrop Footprint Antenna, Skin Thickness 0.032" to 0.049" Figure 6-9. Skin Cutout Detail, Teardrop Footprint Antenna, Skin Thickness 0.049" to 0.
Page 6-12 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-10. Skin Cutout Detail, Teardrop Footprint Antenna, Skin Thickness 0.051" to 0.063" Figure 6-11. Doubler Installation, Teardrop Footprint Antenna, Skin Thickness 0.
G3X Installation Manual – Antennas Page 6-13 190-01115-01 Revision A Figure 6-12. Doubler Installation, Teardrop Footprint Antenna, Skin Thickness 0.049" to 0.051" Figure 6-13. Doubler Installation, Teardrop Footprint Antenna, Skin Thickness 0.
Page 6-14 G3X Installation Manual – Antennas Revision A 190-01115-01 6.5 ARINC 743 Footprint Antenna Inst allation (GA 55A, GA 57X) This section describes the structural mounting of the ARINC 743 footprint antenna (GA 55A, GA 57X) installation. One acceptable method is to use Garmin P/N: 115-00846-0 0 doubler plate.
G3X Installation Manual – Antennas Page 6-15 190-01115-01 Revision A 6.5.2 Antenna Installation Instructions 1. Refer to Table 6-6 (and to Figures in Appendix C) for guidance on selecting the appropriate mounting cutout. Drill or punch t he holes to match the mating part (doubler).
Page 6-16 G3X Installation Manual – Antennas Revision A 190-01115-01 6.5.3 Reference Figures Figure 6-14. Doubler Design, ARINC 743 Footprint Antenna, Skin Thickness 0.
G3X Installation Manual – Antennas Page 6-17 190-01115-01 Revision A Figure 6-15. Doubler Design, ARINC 743 Footprint Antenna, Skin Thickness 0.049" to 0.
Page 6-18 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-16. Doubler Design, ARINC 743 Footprint Antenna, Skin Thickness 0.051" to 0.
G3X Installation Manual – Antennas Page 6-19 190-01115-01 Revision A Figure 6-17. Sample Doubler Location, ARINC 743 Antenna, Metal Skin Aircraft Figure 6-18.
Page 6-20 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-19. Skin Cutout Detail, ARINC 743 Footprint Antenna, Skin Thickness 0.049" to 0.051" Figure 6-20. Skin Cutout Detail, ARINC 743 Footprint Antenna, Skin Thickness 0.
G3X Installation Manual – Antennas Page 6-21 190-01115-01 Revision A Figure 6-21. Doubler Installation, ARINC 743 Footprint Antenna, Skin Thickness 0.032" to 0.049" Figure 6-22. Doubler Installation, ARINC 743 Footprint Antenna, Skin Thickness 0.
Page 6-22 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-23. Doubler Installation, ARINC 743 Footprint, Skin Thickness 0.051" to 0.
G3X Installation Manual – Antennas Page 6-23 190-01115-01 Revision A 6.6 Non-Structural Mount Installation This section provides installation examples and consid erations for non-structura l mounting of teardrop and ARINC 743 footprint antennas.
Page 6-24 G3X Installation Manual – Antennas Revision A 190-01115-01 6.6.2 Considerations for Non- Structural Mounting External mounting of the antenna is preferred, althoug h the antenna can be mounted inside the aircraft.
G3X Installation Manual – Antennas Page 6-25 190-01115-01 Revision A Figure 6-27. Example Non-structural Antenna Mounting Under Glareshield.
Page 6-26 G3X Installation Manual – Antennas Revision A 190-01115-01 6.6.4 Non-structural Installation to Airframe Internal Non-structural Installation Figure 6-28 and Figure 6-29 show examples of under the fabric skin non-structural m ounting of the antenna to the airframe of a tube-and-fabric aircraft.
G3X Installation Manual – Antennas Page 6-27 190-01115-01 Revision A External Non-structural Installation Figure 6-30 is an example of an external, non-struct ur al mounting of the antenna in a tube-and-fabric aircraft. The antenna support bracket shown shoul d be m ade of 2024-T3 Aluminum with a minimum material thickness 0.
Page 6-28 G3X Installation Manual – Antennas Revision A 190-01115-01 Minimum Distance from Metal Tube Structure Requirements Figure 6-31 shows minimum distance from metal tube structure requirements for internal, non-structural mounting of the antenna.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Pag e 7-1 190-01115-01 Revision A 7 Software, Configuration, Databases, and XM Activation 7.1 Configuration Mode Some software loading and all configuration settings a re performed in the configuration mode.
Page 7-2 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.2.2 Audio Data Identification Do the following steps to view the un it’s current audio data inform ation: 1. Turn on the unit in normal mode.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Pag e 7-3 190-01115-01 Revision A 7.3 Software Loading Procedure Software loading is performed in normal mode. Sections 7.3.1 and 7.3.2 describe the GDU and GSU software load procedure.
Page 7-4 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4 Configuration Pages 7.4.1 Main Configuration Page The Main Configuration Page is used to display LRU (device) specific information such as Unit and System ID’s and Database information for the various databases used by the G3X.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Pag e 7-5 190-01115-01 Revision A 7.4.2 ACFT Configuration Page The Aircraft Configuration Page allows setting the para m eters for Flight Planning, Aircraft Identifier, and Map Symbol.
Page 7-6 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.3 W/B (Weight/Balance) Configuration Page The W/B Configuration Page allows setting the weight and balance parameters for the airplane, these parameters are then used on the Main Menu W/B Pa ge in normal mode.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Pag e 7-7 190-01115-01 Revision A 7.4.4 UNITS Configuration Page The Units Configuration Page allows selection of the desired displayed units for t h e listed items in the Units Configuration window.
Page 7-8 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.5 DSPL (Display) Configuration Page The DSPL Configuration Page allo ws setting the parameters for Display and Backlight Control configuration.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Pag e 7-9 190-01115-01 Revision A 7.4.5.1 Display Configuration Window: Backlight Intensity: Can be set to Auto or Manual (t his setting is also available in norm al mode on the Display Setup page).
Page 7-10 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.6 SOUND Configuration Page The SOUND Configuration Page allows setting the pa rameters for various alert and message tones. 1. In configuration mode, use the FMS Joystick to select the SOUND Page.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Page 7-11 190-01115-01 Revision A 7.4.7 COMM Configuration Page The COMM Configuration Page allows setting the param eters for the communication ports. 1. In configuration mode, use the FMS Joystick to select the COMM Page.
Page 7-12 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.5 Garmin Database Updates The GDU 37X MFD database updates can be obtained by visiting the ‘flyGarmin’ website ( www.fly.garmin.
G3X Installation Man u al – Software, Configura tion, Databases, and XM Activation Page 7-13 190-01115-01 Revision A 5. When the update process is complete , the screen updates the database status 6. Once the database(s) have been updated, the SD card can be removed from the unit.
Page 7-14 G3X Installation Manual – Sof tware, Configuration, Databases, and XM Activation Revision A 190-01115-01 all obstacles are necessarily charted and therefore may not be contained in the obstacle database. This database is updated on a 56-day cycle.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-1 190-01115-01 Revision A 8. Post-Installation Checkout and Calibration Procedures The checkout procedures in this section are recommended to be performed after installing the G3X.
Page 8-2 G3X Installation Manual – Post In stallatio n Checkout and Calibration Proced ures Revision A 190-01115-01 8.1 Recommended Test Equipment The following test equipment is recommended to cond.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-3 190-01115-01 Revision A Test the XM Receiver (if applicable): 1. Power on unit and use the FMS Joystick to select the XM Page. 2. Verify that the XM receiver is functioning co rrectly as indicated by the green signal strength bars.
Page 8-4 G3X Installation Manual – Post In stallatio n Checkout and Calibration Proced ures Revision A 190-01115-01 8.3 GSU 73/GMU 44 Post-Installation Calibration Procedures After mechanical and el.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-5 190-01115-01 Revision A For each Calibration Procedure, Table 8-2 lists the LRU’s that require valid calibration data.
Page 8-6 G3X Installation Manual – Post In stallatio n Checkout and Calibration Proced ures Revision A 190-01115-01 8.3.1 Calibration Procedure A: AHRS ORIENTATION 1. Enter configuration mode by holding down the left-hand softke y while powering on the GDU 37X.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-7 190-01115-01 Revision A 9. Use the FMS Joystick to select the direction of the GSU 73 connectors per the on-screen instructions, select OK and press the ENT Key to continue.
Page 8-8 G3X Installation Manual – Post In stallatio n Checkout and Calibration Proced ures Revision A 190-01115-01 8.3.2 Calibration Procedure B: Pitch/Ro ll Offset Compensation by Aircraft Leveling 1. Enter configuration mode by holding down th e left-hand softkey while powering on the GDU 37X (if needed).
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-9 190-01115-01 Revision A 7. Ensure that the aircraft has been prope rly leveled per the on-screen instructions. 8. Use the FMS Joystick to highlight the Calibrate button at the bottom of the display, press the ENT Key to begin the calibration.
Page 8-10 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 8.3.3 Calibration Procedure C: Ma gnetometer Calibration NOTE Calibration Procedure B must be successfully completed prior to Calibration Procedure C.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-11 190-01115-01 Revision A 3. Unlock the GSU Page by pressing softke ys 2, 3, 4 in order (if needed). 4. Ensure that all the required status boxes are checked (Tables 8-2 and 8-3).
Page 8-12 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 7. Ensure that the aircraft has been properly positioned per the on-screen instruction s. 8. Use the FMS Joystick to highlight the Calibrate button at the bottom of the display, press the ENT Key to begin the calibration.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-13 190-01115-01 Revision A 11. The PFD guides the operator to dwell at m u ltiple headings around a complete circle.
Page 8-14 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 8.3.4 Calibration Procedure D: H eading Offset Compensation NOTE Calibration Procedures B and C must have been successfully completed before Calibration Procedure D can be performed.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-15 190-01115-01 Revision A 6. Use the FMS Joystick to highlight the Calibrate button, press the ENT Key. 7. Ensure that the aircraft has been properly positioned per the on-screen instruction s.
Page 8-16 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 11. After the complete calibration is finished, a Done button will appear at the bo.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-17 190-01115-01 Revision A 8.3.5 Calibration Procedure E: Engi ne Run-Up Vibration Test NOTE Calibration Procedure E is required for all installations to validate the vibration characteristics of the installation.
Page 8-18 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 7. Ensure that the aircraft has been properly positioned per the on-screen instruction s. 8. Use the FMS Joystick to highlight the Calibrate button at the bottom of the display, press the ENT Key to begin the calibration.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-19 190-01115-01 Revision A e) Absence of mounting supports recommended by the aircraft manufacturer. f) GSU 73 connector not firmly attached to unit. g) Cabling leading to GSU 73 or GMU 44 not firmly secured to supporting structure.
Page 8-20 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 8.3.6 Calibration Procedure F: Magn etometer Interference Test NOTE Calibration Procedure F is required for initial in stallation verification.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-21 190-01115-01 Revision A 5. Use the FMS Joystick to select MAGNETOMETER INTERFERENCE TEST. 6. Use the FMS Joystick to highlight the Calibrate button, press the ENT Key.
Page 8-22 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 8. Use the FMS Joystick to highlight the Calibrate button at the bottom of the display, press the ENT Key to begin the calibration. 9.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-23 190-01115-01 Revision A Table 8-4. Magnetometer In terference Test Sequence Example Elapsed Time Since Star.
Page 8-24 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 8.3.7 Site Evaluation of Magnetic Distur bances for Magnetometer Calibration Procedure As mentioned in Section 8.
G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Page 8-25 190-01115-01 Revision A NOTE The Magnetometer Calibration Procedure mu st consistently report “CALIBRATION SUCCESSFUL / SITE IS CLEAN” in both the clockwise and counter-clockwise directions for the site to be considered accep table.
Page 8-26 G3X Installation Manual – Post Installation Ch eckout and Calibration Procedures Revision A 190-01115-01 This page intentionally left blank.
G3X Install ation Manual - Troublesho oting Page 9-1 190-01115-01 Revision A 9 Troubleshooting In this section the term ‘Red-X’ refers to a red “X ” that appears on different areas of the display to indicate the failure of that particular function.
Page 9-2 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 9.2 GMU 44 Figure 9-1 – Heading Failure Indication (Full-Screen PFD) 9.2.1 Red-X Failures If a Red-X (steady or intermittent) is displayed on th e heading (Figure 9-1), check the following while the aircraft is on the ground: 1.
G3X Install ation Manual - Troublesho oting Page 9-3 190-01115-01 Revision A 9.3 GSU 73 GSU 73 ground operation is heavily dependent on GP S data inputs. Be sure to correct any GPS performance problems (i.e. interference caused by some types of cell phones or anything that transmits in the area) before troubleshooting the GSU 73/GMU 44.
Page 9-4 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 9.3.1 Attitude/Heading Failure Troubleshooting Prior to troubleshooting an Attitude Failure on-board the aircraft, gather information from the pilot by asking the following questions.
G3X Install ation Manual - Troublesho oting Page 9-5 190-01115-01 Revision A Figure 9-2 – Attitude, Air Data, and E ngine/Airframe Failure Indication (Reversionary or Split-Screen PFD) Figure 9-3 .
Page 9-6 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 Figure 9-4 – AHRS Align Message (PFD) 9.3.2 Heading/Pitch/Roll Troubleshooting The GSU 73 may not be able to provide valid h eading/pitch/roll data for the following reasons: 1.
G3X Install ation Manual - Troublesho oting Page 9-7 190-01115-01 Revision A 9.4 GSU 73 –Air Data Troubleshooting Under normal operating conditions, the GSU 73 pr ovides the following air data infor.
Page 9-8 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 1. Inspect GSU73 pitot/static plumbing inte grity 2. Inspect pitot/static ports and associated equipment 3. If the problem persists replace the GSU 73 with a known good unit 9.
G3X Install ation Manual - Troublesho oting Page 9-9 190-01115-01 Revision A Figure 9-7 – Attitude, Heading, Air Da ta, and Engine/Airframe Failure (Reversionary or Split-Screen PFD).
Page 9-10 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 9.5 Troubleshooting On-board the Aircraft 1. Review the airframe logbook to verif y if any G3X or other avionics or electrical maintenance had been performed recently that may have contributed to the failure.
G3X Install ation Manual - Tr oubleshooting Page 9-11 190-01115-01 Revision A 9.6 GSU Page All three status boxes on the GSU Page (config mode) must indicate a positive state (green check marks) before performing any calibration procedures (Sec tion 8).
Page 9-12 G3X Installation Manual –Troublesh ooting Revision A 190-01115-01 This page intentionally left blank.
G3X Installation Manual – Return to Service Page 10-1 190-01115-01 Revision A 10 Return to Service Information These return to service procedures are intended to ve rify the serviceability of the appliance only. These tests alone do not verify or otherwise validate the airworthiness of the installation.
Page 10-2 G3X Installation Manual – Return to Service Revision A 190-01115-01 10.2.2 New GSU 73 Installed If a new GSU 73 is installed (new serial number), verify the correct software version on the MAIN page in configuration mode.
G3X Installat i on Manual – Pino uts Page A-1 190-01115-01 Revision A APPENDIX A G3X Pinouts A.1 GDU 37X A.1.1 P3701 Connector PIN 1 PIN 17 PIN 18 PIN 33 PIN 34 PIN 50 Figure A-1.
Page A-2 G3X Installation Manual – Pinouts Revision A 190-01115-01 Connector P3701, continued Pin Pin Name I/O 33 CONFIG MODULE CLOCK I/O 34 SIGNAL GROUND -- 35 SIGNAL GROUND -- 36 SIGNAL GROUND -- .
G3X Installat i on Manual – Pino uts Page A-3 190-01115-01 Revision A A.1.4 Serial Data A.1.4.1 RS-232 The RS-232 outputs conform to EIA Standard RS-232C with an o utput voltage swing of 0-5V when driving a standard RS-232 load.
Page A-4 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.1.6 Audio A.1.6.1 Mono Audio Pin Name Connector Pin I/O MONO AUDIO OUT HI P3701 1 Out MONO AUDIO OUT LO P3701 18 -- A.
G3X Installat i on Manual – Pino uts Page A-5 190-01115-01 Revision A A.2 GMU 44 A.2.1 P441 Connector Figure A-2. View of J441 Connector Looking at Rear of Unit Pin Pin Name I/O 1 SIGNAL GROUND -- 2 RS-485 OUT B Out 3 SIGNAL GROUND -- 4 RS-485 OUT A Out 5 SPARE -- 6 POWER GROUND -- 7 SPARE -- 8 RS-232 IN In 9 +12 VDC POWER In A.
Page A-6 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3 GSU 73 A.3.1 Connector Description The GSU 73 has one 62-pin connector (J731) and on e 78-pin connector (J732) located on the connector end of the unit, as shown below. J731 and J73 2 are clearly marked on the connector end plate.
G3X Installat i on Manual – Pino uts Page A-7 190-01115-01 Revision A Connector P731, continued Pin Pin Name I/O 16 RS-232 IN 2 In 17 RS-232 OUT 2 Out 18 RS-232 IN 3 In 19 RS-232 OUT 3 Out 20 ARINC .
Page A-8 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3.2.2 P732 Connector Figure A-5 Rear Connector J732 Viewed from Connector End of Unit Pin Pin Name I/O 1 ANALOG IN 2 LO In 2 ANAL.
G3X Installat i on Manual – Pino uts Page A-9 190-01115-01 Revision A Connector P732, continued Pin Pin Name I/O 40 ANALOG IN 4 LO In 41 ANALOG IN 1 LO In 42 ANALOG IN 10 LO In 43 ANALOG IN 7 LO In .
Page A-10 G3X Installation Manual – Pi nouts Revision A 190-01115-01 A.3.3 Power I/O A.3.3.1 Aircraft Power The GSU 73 has four inputs for aircraft power bus inputs of 14/28Vdc. Pin Connector Pin Name I/O 47 P731 AIRCRAFT POWER 1 IN 49 P731 AIRCRAFT POWER 2 IN 59 P731 POWER GROUND -- 61 P731 POWER GROUND -- A.
G3X Installat i on Manual – Pino uts Page A-11 190-01115-01 Revision A A.3.5 Serial Data Electrical Characteristics A.3.5.1 ARINC 429 Input/Output The ARINC 429 outputs conform to ARINC 429 electrical specifications when loaded with up to 5 standard ARINC 429 receivers.
Page A-12 G3X Installation Manual – Pi nouts Revision A 190-01115-01 A.3.5.3 RS-485 Input The GSU 73 contains one channel of RS-485 serial data communications. Pin Connector Pin Name I/O 1 P731 MAGNETOMETER RS-485 IN B IN 2 P731 MAGNETOMETER RS-485 IN A IN A.
G3X Installat i on Manual – Pino uts Page A-13 190-01115-01 Revision A A.3.6.2 Discrete Outputs INACTIVE: Floating (can be pulled up to externall y sourced Vout in the range 0 Vout 33VDC) Leakage current in the INAC TIVE state is typically 10 uA to ground ACTIVE: Vout 0.
Page A-14 G3X Installation Manual – Pi nouts Revision A 190-01115-01 NOTE If installing an ungrounded thermocouple to an Analog In input, a DC reference must be added to the LO input. This can be accomplished by adding a resistance of 1 M or less between ground and the Analog In LO input that the ungrounded t hermocouple is installed on.
G3X Installat i on Manual – Pino uts Page A-15 190-01115-01 Revision A Pin Connector Pin Name I/O 47 P732 ANALOG IN 22 HI IN 67 P732 ANALOG IN 22 LO IN 28 P732 ANALOG IN 23 HI IN 8 P732 ANALOG IN 23.
Page A-16 G3X Installation Manual – Pi nouts Revision A 190-01115-01 The following table lists the minimum frequency, maximum frequency, and duty cycles for each of these inputs.
G3X Installat ion Man ual – A ppe ndix B Page B-1 190-01115-01 Revision A APPENDIX B Connector Inst allation Instructions B.1 Thermocouple Instal lation into a Backshell Table B-1 lists parts needed to install a Thermocoupl e.
Page B-2 G3X In st al l a tion Man ual – A ppe ndix B Revision A 190-01115-01 Figure B-2. Jackscrew Backshell Thermocouple Installation.
G3X Installat ion Man ual – A ppe ndix B Page B-3 190-01115-01 Revision A B.2 Jackscrew Configuration Module Inst allation into a Jackscrew Backshell Tables B-2 & B-3 list parts needed to install a Jackscrew Configuration Module with pins or with sockets.
Page B-4 G3X In st al l a tion Man ual – A ppe ndix B Revision A 190-01115-01 NOTES For the following steps please refer to Figures B-3 & B-4. 1. Strip back approximately 0.17 inches of insulation from each wire of the four conductor wire harness (item 3) and crimp either a pin (item 4) or a socket (item 9) to each conductor.
G3X Installat ion Man ual – A ppe ndix B Page B-5 190-01115-01 Revision A Figure B-4. Jackscrew Backshell Installation.
Page B-6 G3X In st al l a tion Man ual – A ppe ndix B Revision A 190-01115-01 B.3 Jackscrew Backshell Installation Instructions B.3.1 Shield Block Installation Parts Tables B-4 and B-5 list the parts needed to install a Sh ield Block. Parts listed in Table B-4 are supplied in the jackscrew backshell kits (011-01855-03 and 011- 018 55-04).
G3X Installat ion Man ual – A ppe ndix B Page B-7 190-01115-01 Revision A NOTE In Figure B-5, “AR” denotes quantity “As Re quired” for the particular installation.
Page B-8 G3X In st al l a tion Man ual – A ppe ndix B Revision A 190-01115-01 B.3.2 Shield Termination T echnique – Method A.1 (Standard) NOTE For the following steps please refer to the drawings showing the installation of a Jackscrew Backshell. 1.
G3X Installat ion Man ual – A ppe ndix B Page B-9 190-01115-01 Revision A 3. Connect a Flat Braid (item 4) to the shield e xposed through the window of the prepared cable assembly (item 2) from step 2. The Flat Braid should go out the front of the termination towards the connector.
Page B-10 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 Secondary Method: Solder a Flat Braid (item 4) to the shield exposed through the window of the pre p ared cable assembly (item 2). Ensure a solid electrical connection thr ough t h e use of acceptable soldering practices.
G3X Installat ion Man ual – A ppe ndix B Page B-11 190-01115-01 Revision A 6. Insert newly crimped pins and wires into the appropriate connector housing loc ation as specified by the installation wiring diagrams.
Page B-12 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 B.3.3 Shield Termination Techni que - Method A.2 (Daisy Chain) In rare situations where more braids need to be terminated f.
G3X Installat ion Man ual – A ppe ndix B Page B-13 190-01115-01 Revision A Connect a Flat Braid (item 4) to the folded back shield of the prepared cable assembly. The flat braid should go out the front of the termination to war ds the connector. It is not permitted to exit the rear of the termination and loop back towa rds the connector.
Page B-14 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 Table B-7. Shielded Cable P reparations – (Quick Term) Backshell Size Number of Pins Std/HD Quick Term Min (inches) Quick Term Max (inches) Quick Term Float (inches) 1 9/15 1.
G3X Installat ion Man ual – A ppe ndix B Page B-15 190-01115-01 Revision A B.3.6. Daisy Chain between Methods A and B In rare situations where more braids need to be term inated for a connector than.
Page B-16 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 B.3.7 Double-Shield Termi nation Technique - Method C.1 In rare situations where double shielding may be necessary, the outer shield should be grounded at both ends, while the inner shield s hould be grounded only at one end.
G3X Installat ion Man ual – A ppe ndix B Page B-17 190-01115-01 Revision A B.3.8 Double-Shield Termination Technique (Quick Term) - Method C.2 In addition to method C.1, described previously, another suitable method for double-shielding wires is presented in Figure B-13.
Page B-18 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 B.3.10 Splicing Signal Wires NOTES Figure B-14 illustrates that a splice must be made within a 3 inch window from outside the edge of clamp to the end of the 3 inc h max mark.
G3X Installat ion Man ual – A ppe ndix B Page B-19 190-01115-01 Revision A B.4 Circular Connector I nstallation Instructions B.4.1 Pigtail Installation Parts Table B-9 provides a list of parts needed to install a circular connector with backshell.
Page B-20 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 NOTE In Figure B-15, “AR” denotes quantity “As Re quired” for the particular installation. Figure B-15. Circular Connector Install (19 contact example) B.4.2 Standard Shield Termi nation Technique – Method A Figure B-16.
G3X Installat ion Man ual – A ppe ndix B Page B-21 190-01115-01 Revision A Table B-11. Shielded Cable Preparations for Garmin Connectors Float (in) Window (in) Backshell Size Insert Arrangement Min Max Ideal Min Max Ideal 14 19 1.35 1.60 1.50 2.10 4.
Page B-22 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 Secondary Method Solder a flat braid (item 6) to the shield exposed through t he window of the prepared cable assembly (item 4). Ensure a solid electrical connection thr ough t h e use of acceptable soldering practices.
G3X Installat ion Man ual – A ppe ndix B Page B-23 190-01115-01 Revision A Figure B-17. Insulation/Contact Clearance 5. Insert newly crimped contacts and wires into the appropriate conn ector housing location as specified by the installation wiring diagrams.
Page B-24 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 B.4.3 Daisy Chain Shield Termination Technique – Method A In rare situations where more braids need to be terminated for .
G3X Installat ion Man ual – A ppe ndix B Page B-25 190-01115-01 Revision A B.4.4 Quick Term Shield Termination – Method B If desired, the drain wire termination (item 5) a nd the floating shield termination (item 7) can be effectively combined into a “Quick Term”.
Page B-26 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 Preferred Method Slide a solder sleeve (item 5) onto the prepared cab le assembly (item 4) and connect the flat braid (item 6) to the shield using a heat gun approved for use with solder sleeves.
G3X Installat ion Man ual – A ppe ndix B Page B-27 190-01115-01 Revision A 8. Terminate the ring terminals to the circular b ackshell (item 3) by plac ing items on the provided pan head screw in the.
Page B-28 G3X Installat ion Man ual – A ppe ndix B Revision A 190-01115-01 B.4.6 Daisy Chain Shield Termination Between Methods A and B In rare situations where more braids need to be term inated fo.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-1 (Page C-2 blank) 190-01115-01 Revision A 7.83 198.8 6.04 153.4 2.98 75.8 3.89 98.7 2X 1.72 43.7 .004 0.1 1.09 27.7 [86.7] 3.41 .59 15.
APPENDIX C OUTLINE & INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawings Page C-3 (Page C-4 blank) 190-01115-01 Revision A Drawing is not to scale! Use for dimensions only. 4X 4X 45 ° 45° 4X 4X . 1 60 .160 4 . 1 4.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawings Page C-5 (Page C-6 blank) 190-01115-01 Revision A 2.520 64.01 3.370 85.60 GMU 44 MOUNTING RACK NOTE : 1. DIMENSIONS IN INCHES [mm] 2. SEE SECTIONS 3 AND 4 FOR MOUNTING INSTRUCTIONS OF THE GSU 73 AHRS AND GMU 44 MAGNETOMETER UNIT .
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-7 (Page C-8 blank) 190-01115-01 Revision A 3.37 85.60 2.10 53.34 2.38 60.33 1.84 46.61 8.4 214 .3 8 A IRCRAFT MOUNTING SURFACE NOTES: 1.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-9 (Page C-10 blank) 190-01115-01 Revision A GMU 44 6-32 100 FLAT HEAD BRASS SCREWS REQUIRED 6-32 PAN HEAD BRASS SCREWS 0.24 [6.1] MAX THREAD LENGTH WITHOUT CLEARANCE HOLES AIRCRAFT MOUNTING RACK 2.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-11 (Page C -12 blank) 190-01115-01 Revision A NOTE: 1. BUBBLE NUMBERS IN THIS DRA WING REFER TO REFERENCE NUMBERS LISTED IN T ABLES 3-6 AND 3-7.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-13 (Page C -14 blank) 190-01115-01 Revision A 2.8 71 1.8 46 3.2 81 4.46 113.2 NOTES: DIMENSIONS: INCHES[mm]. 1. DIMENSIONS ARE SHOWN FOR REFERENCE ONLY.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-15 (Page C -16 blank) 190-01115-01 Revision A Figure C-4.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawings Page C-17 (Page C-18 blank) 190-01115-01 Revision A AIRCRAFT SKIN FORWAR D FABRICATE AND INSTALL DOUBLER PLATE TORQUE 20 TO 25 in-lbs 011-01153-00 AS REQUIRED TO COMPLY WITH APPLICABLE GA 55A XM ANTENNA #10-32 PHP x 1.
APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawings Page C-19 (Page C-20 blank) 190-01115-01 Revision A 3.00 76.2 2X 1.25 31.8 5.00 127.0 FORWARD BACKING PLATE OUTLINE .83 [21.1] 2.59 65.8 .60 15.
APPENDIX C OUTLINE & INSTALLATION DRAWINGS G3X Installation Manual – Ou tline & Installation Drawing s Page C-21 (Page C -22 blank) 190-01115-01 Revision A .25 6.4 2.35 59.7 2X 0 2X 1.600 40.64 2X 0 1.000 25.40 2.350 59.69 2X 3.300 83.82 .70 17.
APPENDIX D INTERCONNECT DRAWING G3X Installation M anual – Interconnect Drawings Page D-1 (Page D-2 blank) 190-01115-01 Revision A Figure D-1.1 Notes, 14V Power, and Antennas.
APPENDIX D INTERCONNECT DRAWING G3X Installation M anual – Interconnect Drawings Page D-3 (Page D-4 blank) 190-01115-01 Revision A Figure D-1.2 GDU 37X and GSU 73.
APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY) G3X Installation Manual – Ex ternal Interface Drawings Page E-1 (Page E-2 blank) 190-01115-01 Revision A Figure E-1.
APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY) G3X Installation Manual – Ex ternal Interface Drawings Page E-3 (Page E-4 blank) 190-01115-01 Revision A Figure E-1.
APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY) G3X Installation Manual – Ex ternal Interface Drawings Page E-5 (Page E-6 blank) 190-01115-01 Revision A Figure E-1.
Een belangrijk punt na aankoop van elk apparaat Garmin GTP 59 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Garmin GTP 59 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Garmin GTP 59 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Garmin GTP 59 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Garmin GTP 59 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Garmin GTP 59 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Garmin GTP 59 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Garmin GTP 59 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.