Gebruiksaanwijzing /service van het product 930-115 van de fabrikant GBC
Ga naar pagina of 36
© 2004 GENERAL BINDING CORPORA TION. ALL RIGHTS RESER VED. Do not duplicate without written permission. POLARIS II LAMINA T OR OPERA T OR MANUAL Part Number: 930-1 15 REV : - REV Date: 7-27-04.
The information in this publication is provided for reference and is believed to be accurate and complete. General Binding Corporation is not liable for errors in this publication or for incidental or.
Page I © 2004 General Binding Corporation Operations Manual Polaris II T able of contents 1.0 Safety 1.1 Explanation of symbols 1-1 1.2 General rules of safety 1- 1 1.3 Labels 1- 3 Figure 1.3.1 Safety label placement 1-5 2.0 W arranty 2.0 W arranty 2.
Page II © 2004 General Binding Corporation Operations Manual Polaris II 6.0 Applications 6.1 Film loading and threading 6-1 Figure 6.1.1 Suction Cup Control 6-1 Figure 6.1.2 Suction Cups and Paper Stack 6-1 Figure 6.1.3 Film Leader 6-2 6.2 Helpful hints 6-3 6.
Page 1-1 © 2004 General Binding Corporation Operations Manual Polaris II 1.0 Safety CAUTION: Do not attempt to operate your Polaris Laminator until you completely read and understand this Operations Manual. Y our safety , as well as the safety of others, is important to General Binding Corporation.
Page 1-2 © 2004 General Binding Corporation Operations Manual Polaris II W ARNING: Never use this machine for any other purpose than its intended design and function. CAUTION: Do not make any modifications to this laminator . Unauthorized changes will void your warranty and may cause extensive repairs or create poor output quality .
Page 1-3 © 2004 General Binding Corporation Operations Manual Polaris II 1.3 Labels Safety warning labels are placed at various locations on the laminator . Do not remove any of these labels. They are placed for your safety as well as the safety of those working around you.
Page 1-4 © 2004 General Binding Corporation Operations Manual Polaris II – The safety label below means that you could be seriously injured if you come in contact with the moving chain and sprockets of the drive system. This label is located near all drive sprockets on the machine.
Page 1-5 © 2004 General Binding Corporation Operations Manual Polaris II ( 1) Bet ween pul l r ol l er s an d dec ur l i ng bar ( 1) Cent er rear panel bel ow fi l m unwi nd . ( 2) One on each si de of t h e l a m i nator ( 2) One on each si de of t h e l a m i nator Locat ed n ear Fuse Ho l der Near al l spr o c kets Figure 1.
Page 1-6 © 2004 General Binding Corporation Operations Manual Polaris II.
Page 2-1 © 2004 General Binding Corporation Operations Manual PolarisII 2.0 W arranty GBC warrants to the original purchaser for a period of ninety days after installation that this laminator is free from defects in workmanship and material under normal use and service.
Page 2-2 © 2004 General Binding Corporation Operations Manual Polaris II This page intentionally left blank..
Page 3-1 © 2004 General Binding Corporation Operations Manual Polaris II 3.0 Specifications This section provides specific information regarding the laminator . Any specification not provided must be requested from GBC. 3.1 Film and sheet size Film – Single side films (ie.
Page 3-2 © 2004 General Binding Corporation Operations Manual Polaris II 54 i n ch es 105 i n ches 50. 5 i nch es Figure 3.4.1 Dimensions.
Page 4-1 © 2004 General Binding Corporation Operations Manual Polaris II 4.0 Installation GBC Films Group is committed to a program of ongoing product improvement. As a result, we are providing these instructions so you can insure that your new Polaris Laminator is properly and securely unpacked, moved, and installed.
Page 4-2 © 2004 General Binding Corporation Operations Manual Polaris II 4.2 Setting up your laminator After placing your Polaris laminator , the catch table must be installed. 1. T o assist in the installation of the catch table, a set of tools has been provided.
Operations Manual Polaris II Page 5-1 © 2004 General Binding Corporation 5.0 Operation This section covers the components of the laminator , the control panel, feed table, supply shaft, knife assembly film alignment and tension knobs. 5.1 Components on the laminator (1) POWER ON/ OFF: This is located to the lower right of the catch table.
Page 5-2 © 2004 General Binding Corporation Operations Manual Polaris II (7) CA TCH T ABLE: The catch table is located at the rear of the machine and collects finished sheets.
Operations Manual Polaris II Page 5-3 © 2004 General Binding Corporation (1 1) HEA T ROLLER SAFETY SHIELD: Reduces entanglement, entrapment and inadvertent contact with the heat rollers. See Figure 5.1.7. INFORMA TION: The Heat Roller Safety Shield is designed to cover the heat roller while machine is running.
Page 5-4 © 2004 General Binding Corporation Operations Manual Polaris II (18) P APER GUIDE PIN: The paper guide pin allows the operator to raise the finish product up to the knife separator for a smooth feed into the knife separator . See Figure 5.1.
Operations Manual Polaris II Page 5-5 © 2004 General Binding Corporation 5.2 Control panel Refer to Figure 5.2.1 Control panel (1) ST AR T/SPEED UP: This button has a dual function. When the machine is stopped and all safety covers are closed, press and hold the ST AR T button to begin operation.
Page 5-6 © 2004 General Binding Corporation Operations Manual Polaris II Figure 5.2.1 Control panel 1 2 6 3 5 4.
Operations Manual Polaris II Page 5-7 © 2004 General Binding Corporation 5.3 Operator Screens The T ouch screen has five operator screens. The following is a description of each screen: SPEED SCREEN 0 SPEED 0 COUNT OVER LAP - + T C R M <--- ---> 2 1 34 5 6 8 7 (1) SPEED: Displays current speed of machine in ft/min.
Page 5-8 © 2004 General Binding Corporation Operations Manual Polaris II TEMPERA TURE SCREEN TEMPERATURE O N/ O F F TO P ON <--- ---> BOT OFF 1 2 (1) TOP ON/OFF: This button toggles the heater for the top roll on and off. Be sure to go to the P APER AND FILM screen and select the correct film type for the job running.
Operations Manual Polaris II Page 5-9 © 2004 General Binding Corporation alarm will activate and the laminator will stop. TOP HEA T SENSOR BLOCKED - When the top heat sensor is blocked for more than 5 seconds, this alarm will activate. When the alarm is displayed, the heat automatically shuts off and must be manually reset.
Page 5-10 © 2004 General Binding Corporation Operations Manual Polaris II Figure 5.7.1 Manual T ension Knob SUPPLY SH AFT M A N U A L TE N S IO N ADJUSTM ENT KNOB.
Operations Manual Polaris II Page 6-1 © 2004 General Binding Corporation 6.0 Applications The Polaris will accommodate rolls of film on a 3 inch core. This section will describe how to load and thread film and start an application. This section will also give some helpful hints and important points to remember .
Page 6-2 © 2004 General Binding Corporation Operations Manual Polaris II (9) The cutter On/Off indicator is to be off during the webbing process. W ARNING: Roller are HOT . Use extr eme caution when loading film. Direct contact with the rollers can burn you! (10) Lift the main roller safety shield for ease of webbing the film.
Operations Manual Polaris II Page 6-3 © 2004 General Binding Corporation (22) After the second sheet passes through the nip, the automatic feed table will feed the nextsheet on the stack. As the secondsheet travels through the nip, it passes a paper sensor .
Page 6-4 © 2004 General Binding Corporation Operations Manual Polaris II INFORMA TION: Wrinkles may r esult if an attempt is made to reposition an item once it has entered the nip of the heat rollers. INFORMA TION: When feeding long items, Skewing may occur if the item is not fed into the laminator straight.
Operations Manual Polaris II Page 6-5 © 2004 General Binding Corporation Quick Setup 1. Place sheets in feeder with the grain parallel with the Nip. 2. Be sure that the pile is flat within 1/8 ” . 3. Move feeder up and stop the pile 1 ” from the infeed plate.
Page 6-6 © 2004 General Binding Corporation Operations Manual Polaris II Application Guide The folloing chart is intended to be used as a guide to set up the machine for different applications.
Page 7-1 © 2004 General Binding Corporation Operations Manual Polaris II 7.0 Maintenance & T r oubleshooting General Binding Corporation laminators require minimal maintenance. However , regular maintenance is essential to keep any piece of precision machinery at peak performance.
Page 7-2 © 2004 General Binding Corporation Operations Manual Polaris II 7.4 T roubleshooting As an operator , you can perform some basic troubleshooting before contacting your local service representative. W ARNING: Never remove the side panels in attempt to troubleshoot the laminator .
Page 7-3 © 2004 General Binding Corporation Operations Manual Polaris II Laminator won ’ t run. V erify that unit is plugged in and power is present. Check control panel for machine status. Check fuses. Feed pile light must be on. Feeder not picking up sheets.
Page 7-4 © 2004 General Binding Corporation Operations Manual Polaris II.
Een belangrijk punt na aankoop van elk apparaat GBC 930-115 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen GBC 930-115 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens GBC 930-115 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding GBC 930-115 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over GBC 930-115 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van GBC 930-115 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de GBC 930-115 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met GBC 930-115 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
