Gebruiksaanwijzing /service van het product Control and Booster Panels van de fabrikant GD Commerce
Ga naar pagina of 18
GD Systems Page - 1 Windmill Hardware Specification In order to run Windmill or PanCom software the following system req uirements must be satisfied: 1.1 PC Requirements Pentium Processor running Windows 95 or late r The display must be run in a resolutions mode of 80 0 x 600 or greater.
GD Systems Page - 2 Windmill 3.2 Installing Program files 3.2.1 Installing Windmill from CD · Before starting any installation ensure any oth er applications have terminated to avoid so ftware conflicts. · Insert the CD in the CD player.
GD Systems Page - 3 Windmill You will be prompted to change the disk at various stages but apart from this the procedure is ve ry similar to that detailed in section 3.2.1. 3.2.4 Installing PanCom software from 3.5" disks This is again very similar to the above installation of Windmill from 3.
GD Systems Page - 4 Windmill 5.0 Using Windmill Software 5.1 Defining a new system. In order to create a new system click on the ‘crea te new’ button. The screen will display blank pa nel and device information as shown i n figure 5.
GD Systems Page - 5 Windmill Device Type The device type of the unit installed . To ensure correct operation this value must be correct. The codes follow the product code.
GD Systems Page - 6 Windmill Location text The location text cannot be changed on this scr een and is displayed for refer ence only. Zone number The zone number cannot be changed on this screen and is d isplayed fore reference only.
GD Systems Page - 7 Windmill Radio Sounders Tone The tone for the rad io sounder can be set. The default tone is ton e 4 (swept Tone). If EDA-A910 hard wired soun ders are being used to matc h the tone of the radio units then the tone for the hardwired sounders is set inside the ind ividual units.
GD Systems Page - 8 Windmill Alert When Alert is pressed on the corresponding panel the sounder circuits, auxiliary relays and radio sounders operate as progra mmed. For a more detailed description of the sounder c ircuits, auxiliary relays and radio sounders see the device progr amming section (5.
GD Systems Page - 9 Windmill Display Low Batteries NOT IMPLEMENTED Timeout Values The system has many settings or ope rations, which after a predetermined period o f time automatically cancel.
GD Systems Page - 10 Windmill When downloading settings to the EDA-M200 pa nel, the options and messages must be pe rformed sepa- rately. Select messages first and download the m to the panel. Then select options and downlo ad them to the panel.
GD Systems Page - 11 Windmill Since we want to download from a panel click 'Dow nload from Panels' 6.1.1 Site Information Screen Clicking 'Download from Panels' you will be pres ented with the screen shown Below: Our site name is 'College' so this is entered in the site na me field.
GD Systems Page - 12 Windmill Simply select the location and click Save. Once you are happy with the save loc ation click next >>. 6.
GD Systems Page - 13 Windmill Providing the details shown are correc t connect the PC to the module port of the panel, click con tinue with the mouse and press the dump button insid e the panel Twice.
GD Systems Page - 14 Windmill Data analysis is made up of three main stages: i) Processing of Downloaded Data, ii) Correction of corrupted lines (if any), iii) Report Generation. At this stage files can be added or removed us ing the corresponding buttons.
GD Systems Page - 15 Windmill If the corrected line did not pas s the validity checks or was altered by the user in suc h a way that it no longer passed its validity checks then the Use >> button would be de-activated un til the line passed these checks.
GD Systems Page - 16 Windmill If this highest strength is below the standard 37 then two warning stars are displayed after the strength. The highest strength is also flagged if it is stored as 0, this time using a '-?', to ind icate that it may be a panel anomaly.
GD Systems Page - 17 Windmill Our example uses townhall files 1, 2 and 3. As stated thes e are selected by holding the control key and selecting each file. Upon clicking Open yo u will be returned back to the control screen where the selected files will be displayed in the downloaded files list.
GD Systems Page - 18 Windmill Example M200 Download.
Een belangrijk punt na aankoop van elk apparaat GD Commerce Control and Booster Panels (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen GD Commerce Control and Booster Panels heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens GD Commerce Control and Booster Panels vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding GD Commerce Control and Booster Panels leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over GD Commerce Control and Booster Panels krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van GD Commerce Control and Booster Panels bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de GD Commerce Control and Booster Panels kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met GD Commerce Control and Booster Panels . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
