Gebruiksaanwijzing /service van het product GSD6300 van de fabrikant GE
Ga naar pagina of 44
PUB # 31-9085 09/01 MODEL SERIES: TECHNICAL SER VICE GUIDE GE Consumer Home Services T raining T riton XL Dishwashers EDW4000 EDW4060 GSD6200 GSD6300 GSD6600 GSD6660 GSD6700 PDW7300 PDW7700 PDW7800 PD.
IMPORT ANT SAFETY NO TICE The information in this ser vice guide is intended f or use by individuals possessing adequate backgrounds of electrical, electronic, and mechanical experience. Any attempt to repair a major appliance ma y result in personal injur y and proper ty damage.
– 1 – T able of Content s T able of Content s Introduction ......................................................................................................... 2 Nomenclature ...................................................................
– 2 – Introduction The new T riton XL Dishwashers are pack ed with f eatures to get your dishes cleaner, pots and pans spotless, and k eep your kitchen quieter .
– 3 – Model Designator Designates features – the higher the number , the more features. Nomenclature Model Number Serial Number The first two characters of the serial number identify the month and year of manufacture.
– 4 – Control Panel Features Throughout this manual, features and appearance may vary from your model. Profile Models Control Settings Status Indicator Lights The Status display tells you what ’ s happening while the dishwasher is in operation and may flash, indicating a malfunction (see page 6).
– 5 – COOK Heavy 11.4 gal., 95 min. WARE Medium 10.0 gal., 71 min. Light 10.0 gal., 66 min. This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils. This cycle may not remove burned-on foods. Everyday dishes are safe to be used in this cycle.
– 6 – Start Close the dishwasher door and select the cycle and desired enhancements. Touch the ST ART/RESET pad to begin the cycle. Water fill begins, and approximately 60 seconds later the wash action begins. NOTE: The dishwasher remembers your last cycle so you don ’ t have to reprogram each time.
– 7 – ExtraClean ™ Sensor Selections The light above the selected pad will be ON to indicate which ExtraClean ™ Sensor Selection has been selected. ANTI-BACTERIA Heavy 10.0 gal., 93 min. Medium 8.6 gal., 90 min. Light 7.2 gal., 90 min. This cycle raises the water temperature in the final rinse to sanitize your dishware.
– 8 – LOCK Y ou can lock the controls to prevent any selections from being made. Or you can lock the controls after you have started a cycle. Children cannot accidentally start dishwasher by touching pads with this option selected. T o unlock the dishwasher controls, press and hold the HEA TED DRY pad for 3 seconds.
– 9 – Component Locator Views Door View (Panel and Escutcheon Removed) Control Module Flapper (Active V ent) House Electrical Supply Junction Box Factory T e st Cable Detergent/ Rinse Agent Module.
– 10 – Flood Switch Circulation Pump Motor Junction Box T urbitity Sensor Sump High Drain Loop Drain Pump Drain Line Check V alve W ater V alve Bottom View Factory T est Cable Connector Heating El.
– 11 – P0003687 Inside View Inside Door View Upper Spray Arm Main Conduit Heating Element Fine Filter Lower Spray Arm Inlet Cover Hub Detergent/Rinse Module Detergent Compartment V ent (Active V e.
– 12 – P0003689 Side View Water Va l v e Drain Line Check V alve Fill Funnel Fill Hose Door Spring Drain T ube Assembly.
– 13 – Dishwasher Components Door Components The door components are accessible by removing 3 Phillips screws from each side of inner door and 2 T20 torx screws from the bottom of the door . Carefully separate the inner door panel from the outer door panel.
– 14 – Control Module Removal 1. Remove the outer door panel (see Door Compo- nents ). 2. Open the door and remove the 3 screws from the back on the right side of the escutcheon keypad assembly . 3. Remove 1 screw from the right side of the control module and slide the module out.
– 15 – Stainless Steel Bowed Panel (On Some Models) Disassembly 1. Open the dishwasher door to the fully open (89 degrees open) position. 2. Remove 8 screws (4 screws per side) which hold the outer panel to the door assembly . Be careful not to remove the 2 screws which hold the escutcheon to the door assembly .
– 16 – sure that the protruding ribs from the escutch- eon fit inside the stainless steel front opening. Adjust the position of the outer panel up or down, left or right to center the panel with the escutcheon.
– 17 – Bottom Door Seal The bottom door seal is replaceable by removing the outer door panel (see Door Components ). With the door closed, insert a flat-blade screwdriver under the bottom of the door into the channel and twist to break the bead. Open the door and pull the seal from the channel.
– 18 – Check f or clogged: inlet cov er sump drain pump drain pipe one-wa y check v alve (in drain pipe) YES NO Check f or open circuit between control module and pump or between pump and door interlock switch. If circuits OK, replace control module.
– 19 – through the hub to the lower spray arm and to the main conduit. The main conduit supplies water to the middle and upper spray arms. Inlet Cover Caution: Use care to avoid breaking the clip on the hub when removing the main conduit from hub.
– 20 – O-ring Rotate clockwise 1/4 turn to remove. Fill Funnel The fill funnel is removable with a quarter turn clockwise. There is an O-ring seal between the fill funnel and the dishwasher tub. Calrod ® Heating Element The heating element can be activated using service mode.
– 21 – during the drying cycle, drops to 700 W for gentler drying. W ater inlet temperature must be at least 120 ° F for proper drying. Low water inlet temperature will prevent proper convection air movement and increase drying time substantially .
– 22 – NO NO N COM WX DOOR INTERLOCK WR PX YX FLOOD SWITCH C WATER VALVE 725-1200 J2-2 WA TER V A L VE A ND FLOOD SWITCH L1 voltage from J2-2 W ater V alve and Flood Switch The water valve is a 120 V AC (L1) solenoid valve that is switched on/off by the control module.
– 23 – Flapper V ent Drive ACTIVE VENT + or – 12 VDC at J5-1 + or – 12 VDC at J5-2 M ACTIVE VENT MOTOR BX RX J5-1 J5-2 water level is low , check the following: • Flood switch, flood switch float, and float stem - Flood switch should open when water level is approximately 1/4 in.
– 24 – Flashing Display Light s The status display tells you what’s happening while the dishwasher is in operation and may flash, indicat- ing a malfunction.
– 25 – Service Mode THIS DISHW ASHER IS PROGRAMMED WITH A SERVICE MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING THE DISH- W ASHER. EACH COMPONENT MA Y BE CYCLED TO DETECT IF IT IS FUNCTIONING CORRECTL Y . COMPONENTS ARE CYCLED BY PRESSING KEYP ADS TO THE RIGHT OR LEFT OF THE ST ART/RESET KEYP AD.
– 26 – Factory T est Mode Entering Factory T est Mode Note: This mode can only be entered within the first 2 minutes after power-up. Af ter 2 minutes, factory test mode is unavailable. 1. Disconnect power from dishwasher . W ait 10 seconds and connect power to dishwasher .
– 27 – W ashability Complaint s Hot Water – Ample supply of water at a minimum temperature of 120 ° F is necessary . Do not use dishwasher soon after using clothes washer or filling bath tub. Loading – Consult Owner ’ s Manual on loading procedures.
– 28 – Cycle Progression Chart * When maximum temperature is reached and the calrod is on the calrod will be cycled on and off. **Heater is on for the first 6 minutes then cycles. # The CLEAN NORMAL run will insert the pre-soak after 3 minutes into the first fill.
– 29 – Wiring Diagram W ARNING: Power must be disconnected before servicing the appliance. K E Y P A D CONTROL CIRCUIT BOARD 3-DIGIT DISPLA Y M ACTIVE VENT MOTOR BX RX J7 KEYP AD 1 23 4 5 67 8 9 1.
– 30 – Part s List Note: The components shown in this drawing may differ from the components in your unit. Refer to the microfiche or GEA IPC for the component and part number for your unit.
– 31 – Note: The components shown in this drawing may differ from the components in your unit. Refer to the microfiche or GEA IPC for the component and part number for your unit.
– 32 – Note: The components shown in this drawing may differ from the components in your unit. Refer to the microfiche or GEA IPC for the component and part number for your unit.
– 33 – Note: The components shown in this drawing may differ from the components in your unit. Refer to the microfiche or GEA IPC for the component and part number for your unit.
– 34 – Note: The components shown in this drawing may differ from the components in your unit. Refer to the microfiche or GEA IPC for the component and part number for your unit.
– 35 – 1 31-30365 P M SHEET MINI MANUAL 1 1 31-30530 PM INSTRUCTION INST ALL 1 1 49-5908 P M MANUAL USE & CARE 1 30 WD03X10014 SPRING 2 42 WZ4X376D SCR 10-16X3/4 #8 HX SSTL 3 50 WD13X10006 KEE.
– 36 – 585 WD12X10057 CONDUIT MAIN 1 586 WD12X10059 CONE DOCKING 1 610 WD12X10066 HUB SPRA Y ARM MID 1 61 1 WD01X10102 BEARING SPRA Y ARM UP 1 612 WD01X10109 NUT HUB MID 1 615 WD28X10074 RACK UPPE.
– 37 – 790 WD01X10065 CLAMP HOSE 1 790 WH01X2036 CLAMP HOSE 1 801 WR02X10585 SPRING RECESS DOOR 1 802 WD13X10010 HANDLE LA TCH WH 1 803 WD21X10121 SWITCH INTERLOCK ASM 1 804 WD13X10008 ACTUA TOR H.
– 38 – Review 1. The incoming water temperature must be _________. 2. The dishwasher has a ______ year parts warranty . The electronic module has a _____ year _________________ warranty . 3. The dishwasher has a ______ year labor warranty . 4. If the bearing washer (item #61 1) on the top rack, bottom wash arm is left out, then: a.
– 39 – W arranty Profile Models For The Period Of: GE Will Replace: One Y ear Any part of the dishwasher which fails due to a defect in materials or workmanship. During this full From the date of the one-year warranty , GE will also provide, free of charge, all labor and in-home service to replace the original purchase defective part.
– 40 – What GE Will Not Cover: Lifetime of Product The PermaT uf ® tub or door liner , if it fails to contain water due to a defect in materials or workmanship. During this full warranty , GE will also provide, free of charge, all labor and in-home service to replace the defective part.
– 41 – Notes.
– 42 –.
Een belangrijk punt na aankoop van elk apparaat GE GSD6300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen GE GSD6300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens GE GSD6300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding GE GSD6300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over GE GSD6300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van GE GSD6300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de GE GSD6300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met GE GSD6300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
