Gebruiksaanwijzing /service van het product LS8B van de fabrikant Global Machinery Company
Ga naar pagina of 16
REDEYE ® LS8B 030710 MW ED7 INSTRUCTION MANU AL 250W 200mm Band Sa w with Laser Line Generator • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona .
Contents W arranty 2 Introduction 3 Description of s ymbols 3 Specifications 3 Safety rules for laser lights 3 Safety instructions 4 Additional safety rules f or band saws 5 Unpacking 6 Accessories 6 .
Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . Wear hearing protection. Wear eye protection. Wear breathing protection. Conforms to relevant standards f or electromagnetic compatibility.
• Never aim the beam at any person or an object other than the work piece . • The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person f or longer than 0.25s. • Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces .
8. Use safety accessories. Safety glasses and earmuff s should always be worn. A face or dust mask is also required if the operation creates dust. 9. Do not abuse the pow er cord. Never pull the cord to disconnect the charger from the power point. Keep the cord away from heat, oil and sharp edges.
• Support the work properly. • Never reach over the blade to remove waste or o ff cuts. • Do not attempt to free a jammed blade bef ore first switching off the machine . • Do not slow or stop a blade with a piece o f wood. Let the blade come to rest naturally.
Know y our product 1. Saw blade 2. Upper housing locking screw 3. Lower housing locking screw 4. Upper housing door 5. Lower housing door 6. Laser assembly 7. Laser on/off switch 8. Blade tension knob 9. On/Off switch 10. Work table trunnion 11. Work table 12.
8 Mounting 1. It is best to attach the band saw to a firm, stable surf ace at a convenient working height. A workbench is ideal. 2. Drill four holes in the workbench to match the f our holes in the base of the saw . 3. Attach the band saw to the work bench using 8mm bolts (inserted from the top), lock washers and nuts.
9 3. T o adjust the height of the upper blade guide loosen the blade guide locking knob (17) and then adjust the height using the blade guide setting knob (16). 4. Tighten the blade guide locking knob (17) to secure the upper blade guide in place . 5.
10 4. The work table needs to be tilted 45 ° or removed before the thrust bearing locking screw and guide pins can be adjusted. Thrust bearing adjustment 5. T o adjust the thrust bearing loosen the thrust bearing locking screw using the Allen key supplied.
11 Adjusting the be vel angle W ARNING. Always ensure that the saw is switched off and unplugged from the power supply before making any adjustments. The bevel adjustment allows material to be cut at an angle from 0 ° to 45 ° . 1. Loosen the table locking knob (20).
12 2. While rotating the bandsaw wheel by hand, turn the blade tracking adjustment knob (18) in a clockwise direction if the band saw blade runs towards the front of the saw . 3. Turn the blade tracking adjustment knob (18) in an anti-clockwise direction if the band saw blade runs towards the rear of the saw .
13 1. Remove the rip fence (13) from the table . 2. Remove the U shape from under the work table by removing the two screws and two thumb nuts. 3. Open both housing doors. 4. Swing the lower blade guide out of the way. 5. Loosen the blade tension knob to slacken the blade .
14 Using the REDEYE laser line generat or W ARNINGS. Do not stare directly at the laser beam. Never aim the beam at any person or an object other than the work piece . Do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person.
Maintenance Note . Always wear eye protection when cleaning the tool. W ARNING. Always ensure that the saw is switched o ff and unplugged from the power supply before carrying out any maintenance or cleaning. 1. Keep the tool ’ s air vents unclogged and clean at all times.
Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New.
Een belangrijk punt na aankoop van elk apparaat Global Machinery Company LS8B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Global Machinery Company LS8B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Global Machinery Company LS8B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Global Machinery Company LS8B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Global Machinery Company LS8B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Global Machinery Company LS8B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Global Machinery Company LS8B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Global Machinery Company LS8B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
