Gebruiksaanwijzing /service van het product 2800 van de fabrikant Graco Inc.
Ga naar pagina of 24
OWNER’S MANUAL 824–001 Rev D Supercedes Rev . C HYDRA-CLEAN 2000, 2800 Pressure W ashers Hydra-clean 2000 824–006 Series A 2000 psi (138 bar) Operating Pressure 2400 psi (165 bar) Maximum Wo.
824–001 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation 5 . . . . . .
3 824–001 W ARNING W ARNING HAZARDOUS FLUIDS Improper handling of hazardous fluids can cause serious injury , even death, due to splashing in eyes, ingestion or bodily contamination. D Know specific hazards of fluid being used. D W ear protective eyewear , gloves, clothing, and respirator as recommended by the fluid manufac - turer .
4 824–001 Installation T ypical Installation – Pressure W asher Fig. 1 HIGH PRESSURE HOSE CONNECTION HOSE RACK INLET W A TER CONNECTION 3/4” GARDEN HOSE SPRA Y GUN SPRA Y HOSE Check for Shipping Damage Check the unit for any damage that may have occurred in shipping.
5 824–001 Operation Pressure Relief Procedure INJECTION HAZARD The system pressure must be manually relieved to prevent the system from spraying accidentally .
6 824–001 Operation 4. T rigger the gun until water sprays from the tip indicating that the air is purged from the system. 5. Open the fuel shutof f valve. Be sure the spark plug ignition cable is pushed firmly onto the spark plug. Put the switch in the “on” position and put the throttle in the “run” position.
7 824–001 Operation T rigger Safety Latch W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, always engage the trigger safety latch whenever spraying stops, even for a moment.
8 824–001 Operation Shutdown, Flushing and Storage NOTE: An anti–freeze flush kit 802–327 is available to make flushing easier . CAUTION If water does freeze in the pressure washer , thaw it in a warm room before trying to start it. Do not pour hot water on or into the pump; it may crack the ceramic plungers! 1.
9 824–001 T roubleshooting T o reduce the risk of serious injury , including fluid injection and splashing in the eyes, or on the skin, always follow Pressure Relief Procedure on page 5 before proceeding. W ARNING Problem Cause Solution Engine will not start or is hard to start No gasoline in fuel tank or carburetor .
10 824–001 Problem Cause Solution Frequent or prema - ture failure of the packings Scored, damaged or worn plungers. Install new plungers. See PUMP SER VICE, page 13. Abrasive material in the fluid being pumped. Install proper filtration on pump inlet plumbing.
11 824–001 804–544 Pump Service W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 5 before proceeding.
12 824–001 804–544 Pump Service 6. Lightly grease the retaining screw and the outer end of the plunger . Place the washer , o–ring and backup ring around the screw and install the nut through the plunger . T orque to 1 1 ft–lb (15 N m). NOTE: If you plan to replace the packings, refer to Servicing the V–Packings.
13 824–001 804–559 Pump Service W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 5 before proceeding.
14 824–001 804–559 Pump Service 6. Lightly grease the retaining screw and the outer end of the plunger . Place the washer , o–ring and backup ring around the screw and install the nut through the plunger . T orque to 14.4 ft–lb (19.5 N m).
15 824–001 Accessories W ater Sandblasting Kit 800–120 For abrasive cleaning of stubborn dirt and paint. Requires a spray tip which is not included in kit (1535 uses 805–325, 2030 uses 805–313, 2540 uses 805–321, and 3040 uses 805–317).
16 824–001 Hydra-Clean 2000 Pressure W asher – Parts 04999A 1 30 31 29 32 Model 824–006, Series A 04999 18 19 20 21 22 23 25,26,27,46,57 24 34 Apply sealant to threads Supplied with .
17 824–001 Hydra-Clean 2000 Pressure W asher – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Models 824–006, Series A Ref. No. Part No. Description Qty .
18 824–001 Hydra-Clean 2800G Pressure W asher – Parts Model 824–007, Series A 1 30 31 29 32 2 18 19 20 21 22 23 25,26,27,28,42, 24 34 1 Apply sealant to threads 2 Supplied with pump 1 33 17 16 1.
19 824–001 Hydra-Clean 2800G Pressure W asher – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Models 824–007, Series A Ref. No. Part No. Description Qty .
20 824–001 Pump Assembly – Parts Model 804–544 1 28 58 57 49 50 55 54 56 51 05001 53 52 27 26 25 23 29 30 31 37 32 36 35 33 34 5 24 22 21 8 3 2 4 59 20 19 18 16 14 15 13 12 11 10 9 6 2 7 17 15 1.
21 824–001 Pump Assembly – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Model 804–544 REF P ART NO. NO. DESCRIPTION QTY 1 CRANKCASE 1 2 801-484 PLUG 2 3 802-344 O-RING 1 4 PROTECT OR 1 5.
824–001 Pump Assembly – Parts Model 804–559 4 2 13 14 15 12 16 3 5 6 7 8 9 10 19 18 28 25 26 17 41 45 43 45 1 44 40 42 44 48 46 49 47 10 9 11 75 76 77 78 81 82 79 80 83 84.
23 824–001 Pump Assembly – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES MODEL 804–559 REF P ART NO. NO. DESCRIPTION QTY 1 HEAD, Pump 1 2 801-651 SCREW 8 3 801-652 W ASHER 8 4 KIT 123 O-R.
24 824–001 The SHER WIN–WILLIAMS W arranty and Disclaimers W ARRANTY Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
Een belangrijk punt na aankoop van elk apparaat Graco Inc. 2800 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Graco Inc. 2800 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Graco Inc. 2800 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Graco Inc. 2800 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Graco Inc. 2800 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Graco Inc. 2800 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Graco Inc. 2800 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Graco Inc. 2800 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
