Gebruiksaanwijzing /service van het product 309410 van de fabrikant Graco Inc.
Ga naar pagina of 24
S Controls 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Setup 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Startup 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Digital T racking System (DTS) 12 .
309410 2 Danger d’incendie et d’explosion : les gaz de solv ant et de peinture peuvent s’enfl ammer ou ex ploser . Pour éviter les risq ues d’ incendi e et d’exp losion : N ’utiliser l’appareil qu e dans une zon e extrêmem ent bien aérée.
3 309410 CONTROLS / CONTROLES / COMMANDES / CONTROLES On/Off Switch Interruptor de ligar e desligar Interrupteur marche/arrêt Interruptor de encendido/apagado Drain V alve Válvula de drenagem Vidang.
309410 4 1. Disconnect engine power cord. 2. Release tension bar . Setup 3. Remove engine; tilt and slide back. 4. Install motor; drop in and push forward.
5 309410 5. Look through side vent holes and ensure drive belt is in motor pulley . 6. Secure motor with tension bar . Setup 7. Plug in pressure control power cord.
309410 6 1. Connect appropriate Graco high-pressure hose to sprayer . T ighten securely . 2. Connect other end of hose to gun. Setup 3. T ighten securely .
7 309410 5. Install clean inlet strainer . 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray and store. 7. Check engine oil level. Add SAE 10W–30 (summer) or 5W–20 (winter), if necessary . 8. Fill fuel tank.
309410 8 1. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. 2. T urn prime valve down. T urn pressure control to lowest pressure. Startup 3. Set pump switch OFF .
9 309410 Startup a. Move fuel valve to open b. Move choke to closed c. Set throttle to fast d. Set engine switch ON e. Pull starter cord f. After engine starts, move choke to open g. Set throttle to desired setting – Digital display is functional after engine starts – 4.
309410 10 Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , turn sprayer OFF immediately . Do Pressure Relief in Cleanup, 1. – 3. on page 19. T ighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed.
11 309410 9. Place siphon tube in paint pail. 10. T rigger gun again into flushing fluid pail until paint appears. Assemble tip and guard, page 1 1. SwitchTip and Guard Assembly 1. Engage trigger safety . 2. Insert SwitchT ip . Insert seat and OneSeal .
309410 12 Digital T racking System (DTS) Close cover when spraying to protect from overspray Operation Main Menu 1. Do Startup steps 1. – 3. 2. Start engine or motor , page 9.
13 309410 Digital T racking System (DTS) 3. Short press DTS button to move to Job Gallons (or Liters x 10). 4. Press and hold to reset to zero, or short press DTS button to move to Lifetime Gallons (or Liters x 10). 5. Short press DTS button to move to Auto- Clean T imer operation (Manual 309278).
309410 14 W atchDog Pump Protection System Pump stops automatically when material pail is empty . 1. Do Startup . 2. Press and hold DTS button, release when ON is displayed. Note: GAL (or LITER) flashes while pump protection system is active. EMPTY displays and the pump stops when pump protection system detects an empty material pail.
15 309410 Secondary Menu – Stored Data and W atchDog Pump Protection Modes 1. Do Startup steps 1. – 3. Pressure must be at zero. 2. Start engine or motor , page 9. Pressure display appears. 3. Simultaneously press DTS button and set pump on/of f switch on.
309410 16 Secondary Menu – Stored Data and W atchDog Pump Protection Modes 4. Press and hold to reset to zero, or 5. Short press DTS button to move to Lifetime Hour Meter . 6. Short press DTS button to move to TOT AL Gallons (all pressures). 7. Press DTS button to move to stored error code.
17 309410 9. Short press DTS button again to move to W atchDog MAN (manual) mode. 10. Press and hold to switch between MAN (stan- dard) and AUTO mode. In AUT O mode, W atchDog pump protection is active once pressure is over 1500 psi (103 Bar , 10.3 MPa) 1 1.
309410 18 heavy edges Spray T est Pattern Clearing Tip Clogs 1. T rigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular , 10–12 in.
19 309410 Cleanup 1. Set pump switch OFF . T urn engine or motor OFF . 2. T urn pressure to lowest setting. T rigger gun to relieve pressure. 3. T urn prime valve down. Perform AutoClean procedure (Manual 309278) or follow conventional flushing procedure that follows: 4.
309410 20 5. Unscrew bowl, remove filter . As- semble without filter . Clean filter . 6. Clean filter , guard and SwitchT ip in flushing fluid. 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint.
21 309410 8. T urn engine ON and start engine or motor . Set pump switch ON. 9. T urn prime valve horizontal. 10. T urn pressure control up until motor begins to drive pump. Hold gun against paint pail. T ake trigger safety OFF . T rigger gun until flushing fluid appears.
309410 22 Caution: If flushing with water , do not leave water in sprayer . Flush again with mineral spirits, oil or Pump Armor and leave this protective coating in the sprayer to help prevent freezing or corrosion and increase sprayer life. 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid.
23 309410 DTS Error Codes Service 309409 Reference Repair Manual 309409 or 30941 1 or call your distributor for service.
309410 24 Graco W arranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
Een belangrijk punt na aankoop van elk apparaat Graco Inc. 309410 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Graco Inc. 309410 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Graco Inc. 309410 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Graco Inc. 309410 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Graco Inc. 309410 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Graco Inc. 309410 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Graco Inc. 309410 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Graco Inc. 309410 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
