Gebruiksaanwijzing /service van het product EM390 van de fabrikant Graco Inc.
Ga naar pagina of 38
INSTRUCTIONS-P ARTS LIST 307–724 Rev H Supersedes Rev F (and Rev G – not published) EM 390 PORT ABLE/ELECTRIC AIRLESS P AINT SPRA YER 2500 psi (172 bar) MAXIMUM WORKING PRESSURE U.
W ARNINGS HIGH PRESSURE SPRA Y CAN CAUSE SERIOUS INJUR Y . FOR PROFESSIONAL USE ONL Y . OBSERVE ALL W ARNINGS. Read and understand all instruction manuals before operating the equipment. FLUID INJECTION HAZARD General Safety This equipment generates very high fluid pressure.
MOVING P ARTS HAZARD Moving parts can pinch or amputate your fingers or other body parts. KEEP CLEAR of moving parts when starting or operating the sprayer . Follow the Pressure Relief Procedure on page 2 before checking or servicing any part of the sprayer , to prevent it from starting accidentally .
A VERTISSEMENT La pulvérisation à haute pression peut causer de blessures très graves. Réservé exclusivement à l’usage professionnel. Observer toutes les consignes de sécurité. Bien lire et bien comprendre tous les manuels d’instructions avant d’utiliser le matériel.
RISQUES EN CAS DE MAUV AISE UTILISA TION DU MA TERIAL Consignes générales de sécurité T oute utilisation anormale de l’appareil du pulvérisation ou des accessoires com.
ADVERTENCIA EL ROCIADO A AL T A PRESION PUEDE CAUSAR GRA VES LESIONES. SOLO P ARA USO PROFESIONAL. RESPECTE LOS A VISOS DE ADVERTENCIA. Lea y entienda todo el manual de instrucciones antes de manejar el equipo. PELIGRO DE INYECCION DE FLUIDO Seguridad general Este equipo general un fluido a una presión muy alta.
PELIGRO POR MAL USO DEL EQUIPO Seguridad general Cualquier mal uso del equipo pulverizador o los accesorios, tal como sobre presurización, modificación de piezas, uso de ma.
SETUP If you are supplying your own hoses and spray gun, be sure the hoses are electrically conductive, that the gun has a tip guard, and that each part is rated for at least 2500 psi (172 bar) Maximum Working Pressure .
SETUP Fig 9–1 DO NOT INST ALL A SHUT OFF DEVICE HERE MAIN FLUID HOSE (minimum 50 ft./15.2 m) WHIP HOSE (3 ft./0.9 m) P ACKING NUT/WETCUP Keep 1/3 full with TSL FLUID FIL TE.
OPERA TION 1. Prime the sprayer with paint. a. Close the pressure drain valve. See Fig 10–2. b. Don’t install the spray tip yet! c. Put the suction tube into the paint container . Y ou can hang the pail on the pail hanger .
OPERA TION Fig 1 1–1 SPOTTY P A TTERN – INCREASE PRESSURE GOOD FULL P A TTERN Fig 1 1–2 R O TAT E HANDLE 180 AND TRIGGER GUN TO REMOVE CLOG 0668 RET AINING NUT TIP GUARD SHOWN IN POSITION FOR A VERTICAL SPRA Y P A TTERN 3.
SHUTDOWN AND CARE 1. Check the packing nut/wetcup daily . First relieve the pressure; see page 9. Be sure the wetcup is 1/3 full of TSL at all times to help prevent fluid buildup on the piston rod and premature wear of packings.
WHEN TO FLUSH NOTE: The Pressure Relief Procedure W arning is on page 16. NEVER leave water or water–base paint in the sprayer if there is the slightest change it could freeze. Flush out the water or water–base paint with mineral spirits.
HOW TO FLUSH 1. Relieve pressure. See page 16. 2. Remove the filter bowl and screen; see instruction manual 307–273, supplied. Clean the screen sepa- rately and install the bowl (only) to flush it. See Fig 14–1. 3. Close the pressure drain valve.
APPLICA TION METHODS Always hold the gun perpendicular to the work surface and at an even 12 to 14 in. (300 to 356 mm) from the sur - face you are spraying. See Fig 15–1. Begin moving the gun in a horizontal direction at a steady rate.
TROUBLESHOOTING GUIDE Pressure Relief Procedure To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury fr.
PROBLEM CAUSE SOLUTION Electric motor labors when start- ing, and trips building circuit breaker or fuse Motor capacitor has failed Replace the capacitor . See page 22. Circuit board has failed Replace the circuit board. See page 23.
DISPLACEMENT PUMP To reduce the risk of serious bodily injury , follow the Pressure Relief Procedure W arning on page 16 before checking or repairing any part of the spray system. Unplug the sprayer! W ARNING Removing the Pump.
DISPLACEMENT PUMP Reassembly Procedure 1. Stack these parts one at a time onto the piston valve (224): backup washer (219*), U–cup seal (205*) lips down , and female gland (220*), alternate the polyeth - ylene and leather v–packings (217*, 208*) lips up, and then the male gland (213*).
REPLACING THE CONNECTING ROD and BEARING To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 16 before checking, adjusting, cleaning or shutting of f the sprayer .
REPLACING THE DRIVE ASSEMBL Y To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 16 before checking, adjusting, cleaning or shutting of f the sprayer .
REPLACING THE ELECTRIC MOT OR & CAP ACITOR To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 16 before checking, adjusting, cleaning or shutting of f the sprayer .
REPLACING THE PRESSURE CONTROL & CIRCUIT BOARD To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or inju.
PRESSURE CONTROL ADJUSTMENT USE EXTREME CAUTION WHEN PERFORMING THIS ADJUSTMENT PROCEDURE to reduce the risk of a fluid injection injury or other serious bodily injury , which can result from component rupture, electric shock, fire, explosion or moving parts.
PRESSURE CONTROL ADJUSTMENT NOTE: See Fig 25–1 for the following procedure. 4. Open the needle valve slightly . T urn the pressure con - trol knob (A) to the minimum setting. 5. Plug in the sprayer and turn the switch ON.
P ARTS DRA WING & LIST – PRESSURE CONTROL Part No. 215–860 Ref No. 50 Pressure Control Assembly Includes replaceable items 301 to 316, as listed below NOTES: Numbers with “Ref” preceeding them correspond with the parts lists on pages 28 and 30.
DISPLACEMENT PUMP P ARTS DRA WING & LIST Ref No. Part No. Description Qty 201 180–656 PLUG 1 203 105–444* BALL, sst, 0.
P ARTS LIST – SPRA YER WITH UPRIGHT CART Model 231–001, Series B, Basic Sprayer Includes items 1 to 125 as listed below Ref No. Part No. Description Qty Ref No. Part No. Description Qty 1 065–099 CONDUIT , electrical 4 in.
P ARTS DRA WING – SPRA YER WITH UPRIGHT CART Model 231–001, Series B Basic Sprayer with Upright Cart DANGER LABEL, ENGLISH DANGER LABEL, FRENCH DET AIL A 27 37 55f 55e.
P ARTS LIST – SPRA YER WITH LO-BOY CART Model 220–726, Series C, Basic Sprayer Includes items 1 to 127 as listed below Ref No. Part No. Description Qty Ref No. Part No. Description Qty 1 065–099 CONDUIT , electrical 4 in.
P ARTS DRA WING – SPRA YER WITH LO-BOY CART Model 220–726, Series C Basic Sprayer with Lo-Boy Cart SEE DET AIL BELOW DANGER LABEL ENGLISH DANGER LABEL, FRENCH DET AIL .
P ARTS DRA WING & LIST – COMPLETE SPRA YERS Model 231–390 Complete Upright Sprayer with Flex Gun Includes items 200 to 202, and 204 Model 231–018 Complete Uprigh.
ACCESSORIES Spanish 185–961 German 186–041 Greek 186–045 Korean 186–049 Apply other language here DANGER LABELS The English language DANGER label shown on page 1 and the same label in French is on your spray - er .
TECHNICAL DA TA Maximum W orking Pressure 2500 psi (172 bar) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motor 1/2 HP , AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES.
T ABLE OF CONTENTS W arnings English 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . French 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spanish 6 . . . . . . . .
EM390 Upright Cart — Model 231–001, Basic Sprayer Model 231–390, Complete Sprayer* LoBoy Cart — Model 220–726, Basic Sprayer Model 231–051, Complete Sprayer* * Complete sprayers include 50 ft (15 m) 1/4 in. I.D. hose, 3 ft (0.9 m) 3/16 in.
10 11 12 1 2 3 4 5 6 7 8 9 10 14 15 16 17 1 2 3 4 5 6 7 8 9 11 13 14 15 16 17 18 14a 14b 14c 12 14d 3Z7–724 Rev C Supplement to instruction manual 307–724. EM 390 Airless Paint Sprayer INJECTION HAZARD This form is only a quick reference to the features and frequently ordered parts of this sprayer .
Een belangrijk punt na aankoop van elk apparaat Graco Inc. EM390 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Graco Inc. EM390 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Graco Inc. EM390 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Graco Inc. EM390 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Graco Inc. EM390 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Graco Inc. EM390 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Graco Inc. EM390 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Graco Inc. EM390 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
