Gebruiksaanwijzing /service van het product ti14916a van de fabrikant Graco Inc.
Ga naar pagina of 32
3A0243A Repair GMAX ™ II 3900/5900/7900 T e xSpra y ™ 5900HD/7900HD Airless Spra y er s K orean patent: 10- 0647761 - For P ortable Airless Spraying of Ar chitectural Coatings and P aints - 3300 psi (22.8 MP a, 228 bar) Maximum W orking Pressure IMPORT ANT SAFETY INSTRUCTIONS Read all warnings and instr uctions in this manual.
Warning 2 3A0243A Wa r n i n g The f ollowing are ge neral warnings related to the se tup , us e, maint enance and repair of this equipment. Additional, more specific , warnings may be f ound throug hout the te xt of this manual, where applicab le.
Warning 3A0243A 3 PRESSURIZED ALUMINUM P ARTS HAZARD Use of fluids that are incompat ible with alumin um in pressurized equipment ca n cause serious chemi- cal reaction and equipment r upture . F ailure to f ollow this w ar ning can result in death, serious injury , or property damage.
Maintenance 4 3A0243A Maintenance Pressure Relief Pr ocedure 1. Lock gun trigger sa f ety . 2. T ur n engine ON/OFF switch to OFF . 3. Mov e pump switch to OFF and tur n pre ssure contro l knob fully counterclockwise. 4. Unlock trigger safety . Hold metal par t of gun firmly to side of groun ded metal pail, and trigger gun to relie ve pressure.
Troubleshooting 3A0243A 5 T r oubleshooting Problem Cause Solution E=XX is display ed F ault condition exists . Deter mi ne fault correction from table , page 14. Engine will not star t Engine switch is OFF . T ur n engine switch ON. Engine is out of gasoline.
Troubleshooting 6 3A0243A Pump output is low Strainer is clogged. Clean strainer . Piston ball is no t seating. Ser vice piston ball (see pump manual). Piston packings are worn or damaged. Replace packings (see pump manual). O-ring in pump is wor n or damaged.
Troubleshooting 3A0243A 7 Fluid Pump Runs Constantly 1. P erform Pressure Relief Procedure (page 4), tur n prime valv e f orwar d to SPRA Y position, and turn pow er switch OFF . 2. Remo ve control bo x cov er . T roubleshooting Pr ocedure: With a pressure gaug e plumbed into the paint hose, start the engin e.
Troubleshooting 8 3A0243A Contr ol Boar d Malfunction T roubleshooting Pr ocedure (see follo win g page for actual st eps): Go to step 5. Does the clutch engage? Go to step 2. Do y ou ha ve proper engine v oltage? Go to step 4. Is 1-3 Ohms reading pres- ent? Mechanical problem.
Troubleshooting 3A0243A 9 Contr ol Boar d Malfunction (Steps) - BEEP + - J1 J2 12 -20 AC V - + - + 10-12 DC V - + + 3900 5900/7900 J10 J5 J9 J4 J3 J1 J2 LED D12 J5 - 1-3 ohms - + + - STEP 1. T ur n engine OFF and set meter to continuity . T o Ground STEP 3 .
Troubleshooting 10 3A0243A Con ver tible Electric Motor Will Not Run T roubleshooting Pr ocedure (see follo win g page for actual st eps): See Step 1. Is there over 100 AC volts? See step 2. Is th ere over 100 AC volts? Replace the power swit ch. See Step 3.
Troubleshooting 3A0243A 11 Con ver tible Electric Motor Will Not Run (Steps) V - - L2 L1 + V - - L2 L1 + TS TS +M -M L2 L1 TS TS +M -M - BEEP - TS TS +M -M 100 + DC V - - + STEP 1. Plug in cord and turn s witch ON . Connect wires to control board and tur n me ter to AC vo l ts .
Troubleshooting 12 3A0243A Con ver tible Electric Motor Runs - No A C Output to Spray er Control Boar d T roubleshooting Pr ocedure (see follo win g page for actual st eps): See step 1. Is there o ver 10- 20 AC vo l t s ? YES NO YES YES YES NO NO NO YES See step 2.
Troubleshooting 3A0243A 13 Con vertible Electric Motor Runs - No A C Output to Sprayer Contr ol Boar d (Steps) 10-20 AC V - - + - BEEP - TS TS +M -M L2 L1 Ground 10-20 AC V - - + L2 L1 V - - + - BEEP - STEP 1. Plug in cord and turn s witch ON . Connect wires to transformer and pow er cord.
Digital Display Messages 14 3A0243A Digital Displa y Messages • Digital messages are not a v ailable on all spr ay ers • Blinking LED total count equals digital error code i.e., two b links is the same as E=02 * Error codes also appear on control board as a blinking red LED .
Bearing Housing and Connecting Rod 3A0243A 15 Bearing Housing and Connecting Rod NO TE: The item numbers ref erenced are fo r the 5900 Hi-Bo y models. Th e 3900, 7900 and all Lo-Bo y models ma y hav e diff erent item n umbers. Use the 5900 Hi-Bo y item numbe r and par t to find the correspo nding alter- nate par t and item n umber .
Drive Housing 16 3A0243A Drive Housing Remo val 1. Relie v e pressure; page 4. 2. Remov e bear ing h ousing. Refer to Bearing Hous- ing and Connecting Rod, Remo val , page 15. 3. Premium spray ers: Remove two screws (108) and gallon counter sensor (39).
Pinion Assembly/Clutch Armature /Clamp 3A0243A 17 Pinion Assembl y/Clutc h Armature/Clamp Pinion Assembl y/Clutch Armature Remo val Pinion Assembl y If pinion assemb ly (29) is not remo ved f rom clutch hous- ing (19), do 1. t hrough 3. Otherwise , star t at 4.
Pinion Assembly/Clutch Armature/Clamp 18 3A0243A Installation Clutch Armature 1. Lay two stacks of two dimes on smooth bench sur- f ace. 2. Lay armature (2 5) on two stacks of dimes. 3. Press center of hub (26) down to be nch surf ace. 4. Install armature (25) on engine dr iv e shaft.
Clutch Housing 3A0243A 19 Clutch Housing Remo val 1. Remo ve f our scr ews (20) and lo ck w ashers (21) which hold clutch housin g (19) to engine. 2. Remove scre w (35) from un der mounting plate (D). 3. Pull off clutch ho using (19). Installation 1. Push on clutch hou sing (19).
Clutch Housing 20 3A0243A Engine Remo val NO TE: All ser vice to the engine must be perfo r med by an authoriz ed Honda dealer . 1. Remov e Pinion Assembly/Clutc h Arma- ture/Clamp and Clutch Housing , as instructed on pages 17, a nd 18. 2. Disconnect all necessa r y wir ing.
Pressure Control 3A0243A 21 Pressure Contr ol Pump ON/OFF Switch Re m ova l 1. Remov e two screws (71) and s wing down cov er (130a). 2. Disconnect pu mp ON/OFF swit ch (130f) connector from contr ol board. 3. Press in on tw o retaining tabs on each side of pump ON/OFF switch (130f) and r emov e switch from cov er .
Pressure Control 22 3A0243A Contr ol Board Re m ova l 1. Remov e two scre ws (71) and swing do wn cov er (130a). 2. Remov e strain relief bushings (130r and 123).
Displacement Pump 3A0243A 23 Displacement Pump Remo val 1. Flush pump . 2. Stop pump with piston rod in it s lowest positio n. 3. Do Pressure Relie f , page 4. 4. Separ ate drain hose f rom spra y er . 5. Disconnect ma terial hose from pump . 6. Raise latch loc k.
Displacement Pump 24 3A0243A f . Place u-bolt on pum p door protr usion 8. Ratchet pump door f orward. 9. Open p ump door . 10. Pull out pump pin and place in pin holder Installation 1. Adjust piston r od with pin holder to pull out pi ston rod. T ap piston rod on hard surf ace to push in piston rod.
Displacement Pump 3A0243A 25 5. Rotate pump to align with mater ial hose. Connect mater ial hose a nd hand t ighten to 7 0 in-lb. 6. Tighten latch and rotate latch lock into locked posi- tion. 7. Attach drain hose to spray er . 8. Fill pump with Graco TSL until fluid flows onto top of seal.
Hose Reel 26 3A0243A Hose Reel Remo val 1. Remov e hose fitting from s wivel cap and completely remov e hose. 2. Remov e cap f rom swiv el. 3. Remov e E-clip from s wivel shaft. 4. Remo ve s wiv el cap . 5. Remo ve sna p ring. 6. Remo ve h ose reel. Be sure to k eep your head clear of hose reel while winding up ho se.
Hose Reel 3A0243A 27 Installation 1. Grease sha ft. 2. Make sure two washers and wav e spr ing are on hub bef ore hose reel is installed. 3. Install hose reel onto frame . Place C-clamp on re el and frame to allow snap r ing to fit into place. Install snap ring.
Pivot Replacement 28 3A0243A Piv ot Replacement Remo val 1. Remov e Hose Re el, page 26. 2. Remo ve rigid fluid t ube from s wivel shaft. 3. Remov e two sc rews on pivot plate (A), swiv el shaft (B) if necessary , and remo ve coupling (C) from s wivel sh aft.
Technical Data 3A0243A 29 Te c h n i c a l D a t a Honda GX120 Engine ANSI P ow er Rating @ 3600 r pm 4.0 Horsepower (3.0 kW) Honda GX160 Engine ANSI P ow er Rating @ 3600 r pm 5.5 Horsepower (4.1 kW) Honda GX 200 Engine ANSI P ow er Rating @ 3600 r pm 6.
Technica l Data 30 3A0243A Dimensions Spra yer (no hose and gun) W eight lb (kg) Height in. (cm) Width in. (cm) Length in. (cm) 3900 109 (50) 31.5 (80.0) 22.25 (56.5) 32.0 (81.3) 5900 139 (64) 32.25 (81. 9) 24.5 (62.2) 32.25 (81.9) 7900 146 (67) 32.25 (81.
Notes 3A0243A 31 Notes.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 3A0243 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC.
Een belangrijk punt na aankoop van elk apparaat Graco Inc. ti14916a (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Graco Inc. ti14916a heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Graco Inc. ti14916a vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Graco Inc. ti14916a leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Graco Inc. ti14916a krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Graco Inc. ti14916a bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Graco Inc. ti14916a kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Graco Inc. ti14916a . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
