Gebruiksaanwijzing /service van het product AD1202 van de fabrikant American Dynamics
Ga naar pagina of 32
Model AD1202 MCS Coax Controller Installation and Operating Instructions This manual describes the installation and operating procedures for the AD1202 MCS Coax Pan/Tilt and Lens Controller. The AD1202 Controller allows coax control of four color or monochrome cameras via the video line to the camera site.
The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION................................................................................................. 1 FEA TURES ....................................................................................................... 1 INST ALLA TION .
.
DESCRIPTION The AD1202 MCS Coax Controller is a compact Pan/Tilt, Lens, Preset Scene, and Auxiliary controller for four color or monochrome cameras. The AD1202 provides coax control of four cameras via the video line connection to the camera site.
CONNECTIONS All connections to the AD1202 Coax Controller are made on the unit’s rear panel, illustrated in Figure 2. Typical AD1202 connections with other AD units are illustrated in the Typical System Connections section at the end of this manual.
EXTERNAL Connector A 24-pin connector on the rear panel, labeled EXTERNAL, provides pins for external alarm inputs and control signals. A mating 24-pin plug-in connector with flying leads is provided.
EXTERNAL Connector (Continued) AD MANCHESTER CONTROL CODE OUTPUTS The EXTERNAL connector provides two sets of AD Manchester Control Code lines (Code 1 - pins 5 - 7, and Code 2 - pins 8 - 10) for output of camera control commands (camera pan/tilt/lens/preset/aux) to AD Manchester Control Code units, such as camera site Receivers.
FRONT PANEL CONTROLS The following front panel controls are provided for operator control of a camera site (see Figure 5). The use of these controls is described in the SETUP and OPERATION sections of this manual, pages 6 through 9.
SETUP Factory Reset The AD1202 can be reset to factory default settings which are as follows: • resets the programmed AD1202 camera inputs (see Camera Programming) to cameras 1 through 4, respective.
To program a specific camera select button for a switcher camera number: 1. Press the front panel PGM button on the AD1202. The PGM LED illuminates steadily, and the Channel Select button 1 LED flashes repeatedly. 2. Press the desired AD1202 Channel Select button for the specific camera input to be programmed.
If an input is set as unterminated, that input must be looped to a terminated video device using the lower BNC connector (see Looping Video Outputs, page 2). Coax Code Selection The AD1202 provides two different types of code output for coax control to a camera Receiver: Standard or Enhanced UTC code.
9 Calling a Preset Camera Scene A suitably equipped AD Receiver can store a maximum of 72 preset scenes. The AD1202 can call any of the first four preset scenes using the front panel PRESET buttons. See Preset Scene Programming, page 7, to program preset scenes.
.
Appendix.
BUILT-IN TEST The AD1202 has a built-in test procedure that provides a verification of AD1202 front panel controls. To operate the built-in test: 1. Remove power from the AD1202, and remove the cover from the unit. 2. Press the TEST button on the PCB while applying power to the unit.
T ypical System Connections.
TYPICAL SYSTEM CONNECTIONS AD1202 with four AD1641U Coax Receivers and Alarms REMOTE ALARM CONTACT 3 REMOTE ALARM CONTACT 4 C-2 AD1202 LOOPING VIDEO OUPUTS, ALL INPUTS UNTERMINATED REMOTE ALARM CONTAC.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1641U Coax and two AD1641M Control Code Receivers CAMERA 4 CAMERA 3 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 * 120-Ohm Terminat.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1240 Series P/Ts and two AD1641U Coax Receivers CAMERA 4 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 W B C-4 ALL INPUTS TERMINATED IN 75 Ω LOCAL MONITOR AD1641U COAX RECEIVER AD1641U COAX RECEIVER NOTE: AD1641 Series Receivers shown for illustration.
C-5 TYPICAL SYSTEM CONNECTIONS Two AD1202 Controllers with AD1408A Switcher AD1408A AUX Connector: Pin 1 - Camera ID, bit 0 Pin 2 - Camera ID, bit 1 Pin 3 - Camera ID, bit 2 Pin 4 - Ground AD1408A AD1.
.
Index.
.
AD Manchester Control Code Outputs . . . . . . . . . . . . . . . . 4 Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Response .
.
Problem Possible Causes Suggested Action Operating Problems Cannot program camera numbers or Programming Blocking feature enabled Check and enable front panel controls (page 5) preset scenes No AD1202.
.
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division Sensormatic CCTV Systems Division 1 Blue Hill Plaza 600 Bradley Hi.
SPECIFICATIONS Electrical Ratings: AD1202: 120 VAC, 50/60 Hz, 9 W ADS1202X: 230 VAC, 50/60 Hz, 50 mA Video Signal: AD1202 - EIA RS-170/NTSC Video, 525 lines @ 60 Hz ADS1202X - CCIR/PAL Video, 625 line.
Een belangrijk punt na aankoop van elk apparaat American Dynamics AD1202 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen American Dynamics AD1202 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens American Dynamics AD1202 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding American Dynamics AD1202 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over American Dynamics AD1202 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van American Dynamics AD1202 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de American Dynamics AD1202 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met American Dynamics AD1202 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
