Gebruiksaanwijzing /service van het product AD32E van de fabrikant American Dynamics
Ga naar pagina of 75
8000-1702-02, Rev. B AD32 SYSTEM INSTALLATION AND SERVICE MANUAL.
AD32 SYSTEM INSTALLATION AND SERVICE MANUAL Copyrigh t 1999 All rights reserved CSD 08/99 No part of this manual may be reproduced in any form without written permission from Sensormatic® Electronics Corporation.
EQUIPMENT M ODIFICATION CAUTION Equipm ent ch ang es or m odificat ions n ot express ly approved by Sens orm atic Electronics C orporation, the party responsi ble for FCC com pliance, cou ld void the user' s auth ority to operate th e equipm ent an d could create a hazardou s condition.
CONTENT S AD32 SYSTEM iii PREFACE........................................................................................................................ ............................................V CHAPTER 1 INTRODUCTI ON ...........................
AD32 SYSTEM iv CHAPTER 5 REFERE NCE ............................................................................................................. ................... 5-1 P ART S L IST S .................................................................
AD32 SYSTEM v Preface Thi s manu al provides the information y ou need to install a AD32 Syst em. It ex plains the A D32 Sy stem architecture and gi ves y ou the step-by-step ta sks for installing the system. It also ser ves as a cont inuing re fer ence fo r maint aining a nd tro ubl esho oti ng the AD3 2 System .
AD32 SYSTEM vi Documentation Conventions This manual us es text in different w ay s to id entify different kinds of inform ation. Where appropriate, the following sty les and sy mbols are used. italics Used for term s that are specif ic to AD32 an d for text that requires em phasis; also used for document titles.
AD32 SYSTEM vii • The AD32 Quick Reference (docum ent n um ber 8000-2656- 02) provides quick reference inf ormation about certain pro cedures described in detail in the Operator’s Manual. The Quick reference is a supplem ent to—not a replacem ent of —the inf ormation covered in the Operator’s Manual.
CHAPTER 1 AD32 SYSTE M 1-1 AD32 SYSTEM CHAPTER 1 INTRODUCTION In this chapter: n System Overview ......................................................................1-3 Introduces the AD32 System functions and capabilities. n System Components .....
INTRODUCTION AD32 SYSTE M 1-2.
INTRODUCTION AD32 SYSTE M 1-3 System Overview The AD32 Sy stem is an econ omical v ideo security managem ent sy stem. This m atrix-sw itched CCTV (closed circuit television) surveillance sy stem is capable of cont rollin g up to 32 v ideo in puts (S peedDom e cameras ) and up to f ive vi deo outputs (video mon itors/VCRs ).
INTRODUCTION AD32 SYSTE M 1-4 System Components This section describes the major components of the AD32 S ys tem . SpeedDome and SpeedDome Ultra The SpeedDome an d SpeedDome Ultra cam era dom es are part of a program m able cam era netw ork. These devices let security personnel remotely track a target, near or far, ev en in low ligh t.
INTRODUCTION AD32 SYSTE M 1-5 AD32 Features and Functions The AD32 Sy stem provides th e follow ing f eatures an d fun ctions (in alph abetical order). • 8 VMS alarm in puts an d one relay out put. • 32 program m able tim ed even ts. • 32 x 5 Camera/Monitor matrix sw itching.
INTRODUCTION AD32 SYSTE M 1-6 Specifications SensorNet Bit Ra te: 230.4Kbps Physical L ayer: Non-shielded tw isted pair Lin k L ay er Protocol: SDL C Appli cation Prot ocol: Proprietary Netw ork N ode.
CHAPTER 2 AD32 SYSTE M 2-1 AD32 SYSTEM CHAPTER 2 THEORY The arc hitecture and oper ation of the AD32 System ar e covered in Chapter 1 Introduction. A m ore detailed theor y is not applicable for this pr oduct.
THEORY AD32 SYSTE M 2-2.
CHAPTER 3 AD32 SYSTE M 3-1 AD32 SYSTEM CHAPTER 3 INST ALLA TION In this chapter: n Introduction ..............................................................................3-3 n Before You Begin ......................................................
INSTALLATION AD32 SYSTE M 3-2.
INSTALLATION AD32 SYSTE M 3-3 Introduction This chapter describes how to install and configu re the AD32 S ys tem . The design team determ ines the Sens orNet network topology (dais y- chain , backbon e, or star) and h ow devices will attach to the netw ork.
INSTALLATION AD32 SYSTE M 3-4 Planning the Installation After com pleting the sy stem design and ordering the required components, y our first step in installin g a AD32 Sy s tem i s to devel op a detailed s ys tem lay out.
INSTALLATION AD32 SYSTE M 3-5 the terminate position, a resistor is placed across the SensorNet cable conn ections to su ppress refl ected signals. Think of each SensorNet link as a sing le tw isted pair cable w ith a term inating res istor at each en d.
INSTALLATION AD32 SYSTE M 3-6 Figure 3-2. Bac kbone Link • Locate the driv er any wh ere along th e backbone. • Terminate th e devices at both ends of th e backbone link. Le ave a l l ot he r d evic e s unter minated . • Att ach up to 32 devi ces per lin k.
INSTALLATION AD32 SYSTE M 3-7 Next, deve lo p a ne t wor k dia gram for co nnect i ng J- Boxe s to the EI Ms. Also sho w w hich J-Bo x and E I M mu st be terminated. Final ly, dev elop a net w ork diagram f or the T OUCH T RACK ER controllers , show ing how each one attach es to the VMS.
INSTALLATION AD32 SYSTE M 3-8 Figure 3-4. A D32 Vide o a nd Data Paths 1 3 5 7 9 11 13 15 1 7 19 21 23 25 27 29 31 2 4 6 8 10 12 14 16 18 20 22 24 26 28 31 32 1 2 3 4 5 6 7 8 S I NO NC C 1 2 3 4 5 1 2.
INSTALLATION AD32 SYSTE M 3-9 Installing Power The follow ing equipm ent requires a 110Vac ou tlet: • AD32 V MS • EIMs • J-Box es • Cam eras and dom es not attached to a J-Box • Video m onit.
INSTALLATION AD32 SYSTE M 3-10 Figure 3-5. Dome Conne ction to SensorNe t J-Box 1 1 1 1 P 1 P 4 P 3 P 8 P 7 1 1 1 J W 2 J W 3 J W 1 E1 E2 E3 RS422 SNET P7 S1 P8 P3 P5 J1 P2 P1 P2 P3 P4 P5 P6 HO ST AUX.
INSTALLATION AD32 SYSTE M 3-11 For SpeedDom e , attach a 7-pin fem ale com pression connector t o the dom e end, as detailed in Table 3- 3. Plug this con nector into th e P3 connector on the SpeedDome Un iCard, and plu g the cable' s BNC connector i nto th e board's v ideo port (J1).
INSTALLATION AD32 SYSTE M 3-12 Figure 3-6. S e nsorNet J-Box Connec tions to Video Matrix Switcher Using J-Box P1 P2 P3 P4 P5 P6 HOST AUX F1 F2 F4 F3 P1 P2 P3 P4 P5 P6 HOST F1 F2 AUX 3 2 1 3 2 1 3 2 1.
INSTALLATION AD32 SYSTE M 3-13 Data and Power See Figure 3-6. A t the J-Box end, plug the com posite cabl es into conne cto r s P1 thro ugh P6 . Attac h the Sens orNet cable f rom t he host or driver to pin s 1 and 2 of a 4-pin compres sion con nector.
INSTALLATION AD32 SYSTE M 3-14 Figure 3-7. S ensorNet and V ideo Cable Connec tions Without J-Box 1 1 1 1 P 1 P 4 P 3 P 8 P 7 E1 E2 E3 RS422 SNET P7 S1 P8 P3 P5 J1 P2 EIM J1 J2 J3 E1 ASSY 0301-0 340- .
INSTALLATION AD32 SYSTE M 3-15 Installation Procedures This section describes the installation pro cedures for the AD32 Sy stem com ponents. W A R N I N G: SHOCK HAZARD Do not connect power cables until directed during the power up sequence. AD32 Vide o Matrix Swit cher (VMS) Based on the site survey g uidelines, set the VMS in place.
INSTALLATION AD32 SYSTE M 3-16 Installin g En hanc ed T OUCH T RACKER Controllers Installation Kit (0351-0474-07): INSTL KIT, VM3 2 TOUCH T RKR, W/RJ 4 5 1 Description Qty Part Num ber CABLE ASSY,MDLR,14F T,8 COND,CROSS-P 1 6003-0047-01 SCR,T HD CUT ,M2.
INSTALLATION AD32 SYSTE M 3-17 Figure 3-10. AD32 Wiring Diagram 21 3 54 J- Box #1 EIM #1 DB9 (M) RJ45 RJ45 P1 P2 P3 P4 P5 P6 P8 RJ4 5 RJ4 5 EIM #2 J1 J2 J3 E1 32 1 1-2 TERM INA TED 2-3 UNTERMINAT ED J.
INSTALLATION AD32 SYSTE M 3-18 4. Connect th e pow er transf ormer cable an d the SensorNet netw o rk data cable, and if required, the netw ork data cable to EIM #2, to the compression connect or (2109-0254-04), an d conn ect it to J3 on the EIM.
INSTALLATION AD32 SYSTE M 3-19 The Tracker Ball provides variable speed cont rol of a camera’ s pan and tilt. The zoom and focus buttons lets you control a cam era’s zoom and focus. Fig ure 3-12 shows the default button setup. The T OUC H T RACKER ’s m e nu mode ( Error! Reference source not found.
INSTALLATION AD32 SYSTE M 3-20 3. Press the zoom (top line) or focus (bottom line) button to select the Adjust V-Phase menu optio n. Adjust V-Ph ase <NEXT> < PREV> 4. Press Next or Prev to o bs e rve V -Pha s e thro ugh the oscilloscope. 5.
INSTALLATION AD32 SYSTE M 3-21 You can also v iew the selected dom e’s firm w are product codes. 1. While in the Cam era Control Mode, press the Info button on the T OUCH T RACKER ’ s key pad.
INSTALLATION AD32 SYSTE M 3-22 Notes:.
CHAPTER 4 AD32 SYSTE M 4-1 AD32 SYSTEM CHAPTER 4 SERVICE In this chapter: n Introduction ..............................................................................4-3 n Troubleshooting Procedures ...................................................
SERVICE AD32 SYSTE M 4-2.
SERVICE AD32 SYSTE M 4-3 Introduction This chapter contain s the A D32 Sys tem trou bleshootin g procedures. Tools and Equipment Requi red Only the V-Phase Adjustment Procedure requires the use of tools and equipm ent. The required items are listed in that section.
SERVICE AD32 SYSTE M 4-4 1. Connect th e patch cables, “ T” connector, and scope as show n in the f ollow ing diagram . 2. Select a camera on the AD 32 Syst em th at doe s not ha ve the sc ree n rol ling pr ob lem. Observe t he com posite v ideo from the camera on the scope an d note the location of the syn c pulses on the display.
SERVICE AD32 SYSTE M 4-5 Enhanced T OUCH T RACKER Maintenance Perform these procedures to keep y our T OUCH T RACK ER s operating properly : • Track er Ball does n ot m ove sm oothly or binds or sticks. − Check for dus t and debris arou nd th e Tracker Ball.
SERVICE AD32 SYSTE M 4-6 Notes:.
CHAPTER 5 AD32 SYSTE M 5-1 AD32 SYSTEM CHAPTER 5 REFERENCE In this chapter: n Parts Lists ..................................................................................5-3 n Drawings.................................................................
DRAWINGS AND PARTS LIST AD32 SYSTE M 5-2.
DRAWINGS AND PARTS LIST AD32 SYSTE M 5-3 Parts Lists Assemb lies 01A DTT32E TT RKER,A D32 CONTROLLER A 0 Item Qty Part Number Descripti on 1 1 5604-00XX-XX XFR OPTION,TOUCH TRKER 2 1 0351-0547-XX POW .
DRAWINGS AND PARTS LIST AD32 SYSTE M 5-4 10 2 1540-0094-01 CA P,100UF,25V,20% ,AL,RD,C35,39 11 23 1509-1032-161 CAP,.01UF,100V,10%,X 7R,1206, C38,77-89,105-112,114 12 1 1545-0011-01 CA P,330UF,25V,20% ,AL,8x10.
DRAWINGS AND PARTS LIST AD32 SYSTE M 5-5 Drawings This section lists the drawing s that are available. Drawin gs identif ied by a ✔ are inclu ded. Assemblies 0300-0997- 01 T OUCH T RACK ER Speaker A.
DRAWINGS AND PARTS LIST AD32 SYSTE M 5-6 Notes:.
APPENDIX A AD32 SYSTE M A-1 AD32 System CHAPTER A J- B O X E S Regulatory Requ irement: These products can only be used w ith Se nsorm atic Electronics C orporation product s. J-Box es (jun ction bo xes) pro vide power an d data conc entratio n for attac hed SpeedDome an d SpeedDome U ltra cam era domes.
APPENDIX A AD32 SYSTE M A-2.
APPENDIX A AD32 SYSTEM A-3 SensorNet 1-Position Junction Box (J-Box) This weathe r-resistant b ox provid es powe r and data com m unications f or one SpeedDom e or SpeedDome Ultr a cam era dom e. One of these boxes ships with each Outdoor Sensor Net SpeedDome.
APPENDIX A AD32 SYSTE M A-4 6. Using th e enclosure' s mounting brackets as a template, m a rk the m ounting hole locations on the design ated area of the w all. 7. Drill holes at the m arked areas to accomm odate the req uire d mounting ha rd ware.
APPENDIX A AD32 SYSTE M A-5 Figure A-4. PCB Connectors and Jumpers F1 F2 F4 F3 P1 HO ST A UX +5VDC AC PWR FALSE CD 123 AUX HOST P7 P1 HOST AUX +5VDC AC PWR FALSE CD 123 AUX HOST P7 P8 3 2 1 3 2 1 3 2 .
APPENDIX A AD32 SYSTE M A-6 Specificat ions Electrical Power S ource (50–60Hz) ....... 100–120/200–240Vac Power C onsu mpti on:.............. 250W max . Voltage Outpu t: ..................... 28Vac, 5A m ax. Fuses F1, F2:........................
APPENDIX A AD32 SYSTE M A-7 SensorNet 6-Position Junction Box (J-Box) This box provides power and data c om m unications for up to s ix SpeedDom e or SpeedDom e Ultra cam era dom es. IMPORT A NT: Regulatory Requireme nts and other declarations on page A-10.
APPENDIX A AD32 SYSTE M A-8 6. Using th e enclosure' s mounting brackets as a template, m a rk the m ounting hole locations on the design ated area of the w all. 7. Drill holes at the m arked areas to accomm odate the req uire d mounting ha rd ware.
APPENDIX A AD32 SYSTE M A-9 Figure A-9. PCB Connectors and Jumpers F1 F2 F4 F3 P1 P2 P3 P4 P5 P6 HOST AU X +5VDC AC P WR FALSE CD 123 456 AUX HOST P7 P1 P2 P3 P4 P5 P6 HO ST AUX +5VDC AC P WR FALSE CD.
APPENDIX A AD32 SYSTE M A-10 Specificat ions Electrical Power S ource (50–60Hz) ....... 100–120/200–240Vac Power C onsu mpti on:.............. 250W max . Voltage Outpu t: ..................... 28Vac, 5A m ax. Fuses F1, F2:.......................
APPENDIX B AD32 SYSTE M B-1 AD32 System APPENDIX B VIDEO MA TRIX SWIT CHER ALARM AND RELA Y CONNECTIONS In this appendix: n Alarm and Relay Connections.
APPENDIX B AD32 SYSTE M B-2.
APPENDIX B AD32 SYSTE M B-3 Alarm and Relay Connections The back panel of the AD32 Video Matrix Switch er provides eigh t alarm contact inpu ts, an extern al freq uency synchro nizat ion inp ut, a nd c onta ct termin ations for an in ternal alarm -activated relay .
Appendix B AD32 SYSTE M B-4 Notes:.
APPENDIX C AD32 SYSTE M C-1 AD32 System APPENDIX C ADDING DOMES TO J- B O X E S In this appendix: n Attaching Additional Domes to J-Box ...............
APPENDIX C AD32 SYSTE M C-2.
APPENDIX C AD32 SYSTE M C-3 Attaching Additional Domes to J-Box When attaching additional domes to SpeedDome Ultra, strip 1.2cm (.5 in.) of in sulation from each Sens orNet cable conductor 30.5cm (12 in.) from th e end. Fold each w ire in the m iddle of the stripped area, and s ecure SpeedDome Ultra' s connector (Figure C- 1).
APPENDIX C AD32 SYSTE M C-4 Notes:.
APPENDIX D AD32 SYSTE M D-1 AD32 System APPENDIX D AT TA C H I N G SENSORLINK PC In this appendix: n Attaching SensorLink PC to the AD32 System .......
APPENDIX D AD32 SYSTE M D-2.
APPENDIX D AD32 SYSTE M D-3 Attaching SensorLink PC to the AD32 System The Sensor Link PC ( SLP C) system allows remot e viewing and c ontr ol o f up t o 16 AD32 -co ntro lled cameras and dom es.
APPENDIX D AD32 SYSTE M D-4 Notes:.
Survey Did this docum ent help you do your job? Pl ease complete this short sur vey by circl ing the number that best matches your opinion of each statem ent. Also, give us your com ments on how we could i mprove item s you rate 3 or lower . Provide examples, if necessary.
Postage Stamp Sensormatic Electronics Corporation 951 Yamato Road Boca Raton, Florida 33487 Attention: Technical Comm unications Depar tment Dept. 440 / MS C- 27 2.
AMERICAN DYNAMICS 1 Blue Hill Plaza Pearl River, New York 10965 U.S.A. Business: 914- 624-7600 Tec hnical Support Center: 800- 442-2225 Sensormatic Electronics Corporation 951 Yamato Road Boca Raton, Florida 33431-0700 U.
Een belangrijk punt na aankoop van elk apparaat American Dynamics AD32E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen American Dynamics AD32E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens American Dynamics AD32E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding American Dynamics AD32E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over American Dynamics AD32E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van American Dynamics AD32E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de American Dynamics AD32E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met American Dynamics AD32E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
