Gebruiksaanwijzing /service van het product HN Series van de fabrikant Hanns.G
Ga naar pagina of 21
19 inch HN Series TFT LCD Monitor USER’S MANUAL.
User’s Manual 2 Before operating the monitor, please read th is manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference S t atement This equipment has been tested and found to comp ly with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual 3 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirement s in the world.
User’s Manual 4 Recycling Information We, the HannStar Display Corp. care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial te chnology devices at the end-of-life.
User’s Manual 5 T ABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 6 PRECAUTIONS ......................................................................................... 6 SPECIAL NOTES ON LCD MONIT ORS .
User’s Manual 6 SAFETY NOTICE 1. The changes or modifications not expr essly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord , if any , must be used in order to comply with the emission limits.
User’s Manual 7 SPECIAL NOTES ON LCD MONIT ORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on agai n to make sure the flicker disappears.
User’s Manual 8 BEFORE YOU OPERA TE THE MONIT OR FEA TURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions : 1280 X 1024 @60Hz • EP A ENERGY ST AR .
User’s Manual 9 INST ALLA TION INSTRUCTIONS Inst all Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer secti on of the base points forward. 3. Snap the monitor into its base.
User’s Manual 10 To set up the device, you need to assemble the monitor stand. Join the stand base to the stand post. You should be able to hear it slot in. Insert the screw enclosed, tightening it with a coin or a screwdriver, so that the stand base is attached securely to the stand post.
User’s Manual 11 CONTROLS AND CONNECT ORS CABLE CONNECTIONS: T urn of f your computer before performing the procedure below . 1. Connect one end of the 15-pi n D-Sub cable to the back of the monitor and connect the other end to the computer ’s D-Sub port.
User’s Manual 12 ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of t he monitor , then adjust the monitor ’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle.
User’s Manual 13 OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (S ee Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.
User’s Manual 14 FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor ’s power . • Power Indicator: Green — Power On mode. Orange — Off mode. • MENU / ENTER: 1. Active OSD menu or f unction adjust confirm or 2.
User’s Manual 15 HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness/Contrast adjustment: Brightness: Adjusts brightness by using the buttons < or > ( ② and ⑤ in fig. 4). Contrast: Adjusts screen contrast by using the buttons < or > ( ② and ⑤ in fig.
User’s Manual 16 OSD Diagram OSD Description OSD Control: H. OSD Position: Controls the OSD menu’s horizontal position. V. OSD Position: Controls the OSD menu’s vertical position. OSD Timeout: Determines how long (in seconds) the OSD menu waits before closing automatically after no action has been performed.
User’s Manual 17 electrical energy by reducing power consum ption when there is no video-input signal present. When there is no video input signal th is monitor, following a time-out period, will automatically switch to an O FF mode. This reduces the moni tor's internal power supply consumption.
User’s Manual 18 TECHNICAL SUPPORT (F AQ) Q & A FOR GENERAL DEFECTIVE PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position *Power Cord sh.
User’s Manual 19 ERROR MESSAGE & PO SSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly con nected, If the connector is loose, tighten the connector ’s screws. 2. Check the signal-cable’s connection pins for damage.
User’s Manual 20 APPENDIX SPEC IFICA TIONS Driving system TFT Color LCD Size 48.2cm(19.0") Pixel pitch 0.294mm(H) x 0.294mm(V) LCD Panel Brightness 270cd/m 2 (T ypical) Contrast 700:1 (T ypical.
User’s Manual 21 CONNECT OR PIN ASSIGNMENT 15 - Pin Color Display Signal Cable: 15 6 10 11 15 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Ground 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14.
Een belangrijk punt na aankoop van elk apparaat Hanns.G HN Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hanns.G HN Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hanns.G HN Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hanns.G HN Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hanns.G HN Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hanns.G HN Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hanns.G HN Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hanns.G HN Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
