Gebruiksaanwijzing /service van het product HW173DBB van de fabrikant Hanns.G
Ga naar pagina of 20
HW173 HSG1044.
User’s Manual Before operating the monitor, please read this manual thoroughly. This m anual should be retained for future reference. FCC Class B Radio Fr equency Interference S tatement This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environm ent protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ...................................................................................................... 5 PRECAUTIONS .....................................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any , must be used in order to comply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. x Due to the nature of the fluorescent light, the screen m ay flicker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE OPERA TING THE MONIT OR FEA TURES x 17” W ide screen TFT Color LCD Monitor x Crisp, Clear Display for W indows x Recommended Resolutions : 1440 X 900@60Hz x EP A ENERGY ST AR .
User’s Manual INST ALLA TION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your com puter before performing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE x For optimal viewing it is recommended to look at the full face of the m onitor , and then adjust the monitor ’ s angle to your own preference. x Hold the stand so you do not topple the monitor when you change the monitor’ s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preference.
User’s Manual FRONT P ANEL CONTROL x Power Button: Press this button to switch ON/OFF monitor ’ s power . x Power Indicator: Green — Power On mode. Orange — Power Saving mode. x MENU / RETURN: 1. T urn the OSD menu on/off or return to the previous m enu.
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select ψ BRIGHTNESS ω option to adjust the brightness value. CONTRAST Adjust the contrast value of the display according to your preference.
User’s Manual H-POSITION Select the ψ H-POSITION ω option to shift the screen image to the left or right. Enter the option and adjust the level. [For VGA only] V - POSITION Select the ψ V -POSITION ω option to shift the screen image up or down. Enter the option and adjust the level.
User’s Manual F ACT OR Y RESET Select the ψ F ACTOR Y RESET ω option to reset to the monitor’ s default setting. This will erase the current settings. Enter the option and select On or Of f. INFORMA TION Display Horizontal frequency/V ertical frequency/Resolution information.
User’s Manual PLUG AND PLA Y Plug & Play DDC2B Featur e This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional inform ation about its display capabilities.
User’s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User’s Manual 28 1400×1050 @60Hz 65.317 59.978 29 1440×900 @60Hz 55.469 59.901 30 1440×900 @60Hz 55.935 59.887 31 1440×900 @75Hz 70.635 74.984 19.
User’s Manual APPENDIX SPECIFICA TIONS Driving system TFT Color LCD Size 17” LCD Panel Pixel pitch 0.255mm(H) x0.255m m(V) H-Frequency 24 KHz – 80 KHz V ideo V -Frequency 55Hz– 75Hz Display Colors 16.
Een belangrijk punt na aankoop van elk apparaat Hanns.G HW173DBB (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hanns.G HW173DBB heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hanns.G HW173DBB vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hanns.G HW173DBB leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hanns.G HW173DBB krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hanns.G HW173DBB bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hanns.G HW173DBB kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hanns.G HW173DBB . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
