Gebruiksaanwijzing /service van het product 44506 van de fabrikant Harbor Freight Tools
Ga naar pagina of 20
8” Drill Press Model 44506 set uP anD OPera ting instructiOns Visit our website at: http://www .harborfreight.com read this material before using this product. Failure to do so can result in serious injury . sa Ve this Manual. Copyright © 2010 by Harbor Freight T ools ® .
Page 2 For technical questions, please call 1-800-444-3353. SKU 44506 cOntents iMPOrt ant saFetY inFOrMa tiOn ................................. 3 general t OOl saFetY W arnings . 3 grOunDing instructiOns .......... 5 1 10-120 V~ grOunDeD tOOls: tOOls With three PrOng Plugs 5 Drill Press saFetY W arnings .
Page 3 For technical questions, please call 1-800-444-3353. SKU 44506 sa Ve this Manual Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures.
Page 4 For technical questions, please call 1-800-444-3353. SKU 44506 USE RIGHT TOOL. Don’t force tool or 8. attachment to do a job for which it was not designed. recOMMenDeD MiniMuM Wire gauge FOr eXtensiOn cOrDs (120 VOl t) naMePla te aMPeres (at full load) eXtensiOn cOrD length 25’ 50’ 100’ 150’ 0 – 6 18 16 16 14 6.
Page 5 For technical questions, please call 1-800-444-3353. SKU 44506 grOunDing instructiOns tO PreVent electric shOck anD Dea th FrOM incOrrect grOunDing Wire cOnnectiOn reaD anD FOllOW these instructiOns: 1 10-120 V~ grounded t ools: t ools with three Prong Plugs In the event of a malfunction or 1.
Page 6 For technical questions, please call 1-800-444-3353. SKU 44506 The included chuck key is specially 5. designed to be self-ejecting, reducing the risk of ejecting at high speed. Only use the included chuck key or an identical replacement key . DO nOt OPera te With anY 6.
Page 7 For technical questions, please call 1-800-444-3353. SKU 44506 medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
Page 8 For technical questions, please call 1-800-444-3353. SKU 44506 sPeciFica tiOns Electrical Input 120 V~, 60 Hz, 1/3 HP (3.6 A) Motor Speed 1750 RPM (No Load) Spindle Speeds 620, 1 100, 1720, 234.
Page 9 For technical questions, please call 1-800-444-3353. SKU 44506 (C3). Slide it down on the Column T ube as far as it will go. Align it so that it faces straight forward, inline with the Base. Thread in two Set Screws (1 1), into the 6. side of the Head (1) and tighten.
Page 10 For technical questions, please call 1-800-444-3353. SKU 44506 OPera ting instructiOns read the entire iMPOrt ant saFetY inFOrMa tiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 44506 with enough extra length to allow free movement while working. Clamp workpiece or brace against 3. column to prevent rotation. There must not be objects, such as utility 4. lines, nearby that will present a hazard while working.
Page 12 For technical questions, please call 1-800-444-3353. SKU 44506 Maintenance anD ser Vicing Procedures not specically explained in this manual must be performed only by a qualied technician.
Page 13 For technical questions, please call 1-800-444-3353. SKU 44506 adjusting the Feed Wheel return t ension spring cautiOn! Wear an ansi-approved full face shield during this procedure. Move the Chuck to its uppermost 1. position. Loosen Hex Nuts (31) and move both to 2.
Page 14 For technical questions, please call 1-800-444-3353. SKU 44506 t roubleshooting Problem Possible causes likely solutions T ool will not start. Cord not connected. 1. No power at outlet. 2. Internal damage or wear . 3. Check that cord is plugged in.
Page 15 For technical questions, please call 1-800-444-3353. SKU 44506 Part Description 1 Head w/ Roll Pin and Trim 2 Nut, Lock, M8x1.25-8 3 W asher , 5/16 x 1 1/16 x 1/16 4 Screw , Hex, M8x1.25-25 5 Pulley , Motor 6 Screw , Hex Soc. Set, M6x1.0-10 7 Motor 8 Stop, Motor 9 Spring, Motor Stop 10 Knob, Motor Adjusting 11 Screw , Hex Soc.
Page 16 For technical questions, please call 1-800-444-3353. SKU 44506 head assembly Diagram.
Page 17 For technical questions, please call 1-800-444-3353. SKU 44506 When ordering a part from this drawing, add an “A” prex to the part number . Parts list and Diagram a - Pulley and spindle Part Description A1 Bushing, Rubber A2 Knob A3 Screw , Pan Hd.
Page 18 For technical questions, please call 1-800-444-3353. SKU 44506 When ordering a part from this drawing, add a “B” prex to the part number . Parts list and Diagram b - chuck and spindle shaft Part Description B1 Gasket, Quill B2 Bearing, Ball, 12 mm B3 Tube, Quill B4 Screw , Pan, M5x0.
Page 19 For technical questions, please call 1-800-444-3353. SKU 44506 When ordering a part from this drawing, add a “C” prex to the part number . Parts list and Diagram c - base and t able Part Description C1 Support, T able with Scale C2 Support, Lock Handle C3 T ube, Support C4 Base C5 Screw , Hex Hd.
Page 20 For technical questions, please call 1-800-444-3353. SKU 44506 liMiteD 90 Da Y W arrantY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durabili.
Een belangrijk punt na aankoop van elk apparaat Harbor Freight Tools 44506 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Harbor Freight Tools 44506 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Harbor Freight Tools 44506 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Harbor Freight Tools 44506 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Harbor Freight Tools 44506 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Harbor Freight Tools 44506 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Harbor Freight Tools 44506 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Harbor Freight Tools 44506 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
