Gebruiksaanwijzing /service van het product 66630 van de fabrikant Harbor Freight Tools
Ga naar pagina of 22
10” HEA VY -DUTY 15 AMP T ABLE SA W 66630 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 3 DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 4 or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 5 controlled workpiece to lift up and out of the saw toward the operator . Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below: Fence must be completely parallel • to the saw blade.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 6 Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A dif- ferent stick design may be used if it properly protects against all hazards.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 7 When servicing use only identical 14. replacement parts. Only use safety equipment that has 15. been approved by an appropriate standards agency . Unapproved safety equipment may not provide adequate protection.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 8 reduce the risk of vibration-related injury: Anyone using vibrating tools regu- 1. larly or for an extended period should rst be examined by a doctor and then have regular medical check- ups to ensure medical problems are not being caused or worsened from use.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 9 stood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 10 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 15 A Motor No Load Speed 4800 RPM Blade Diameter 10” Arbor Diameter 5/.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 1 1 (109) and that the tabs are on the INSIDE slot of the Splitter . Use a framing square (not included) 8. to make sure the Saw Blade and Splitter assembly are square. If not square, loosen the Splitter Bracket and adjust until the Splitter is properly aligned with the Saw Blade.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 12 Blade Depth and Angle Adjustment The Blade (96) depth should be set 1. so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 13 Aligning and Adjusting the Rip Fence (146) 1. W ARNING! A misaligned Fence can cause kickbacks and jams. T o reduce risk of injury , always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and T able grooves.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 14 edge of the square until it touches the marked tooth. Rotate the Blade and check the same 7. marked tooth at the rear of the T able Saw . If the front and rear measurements 8. are not identical, have a qualied ser - vice technician repair the T able Saw .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and Work Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 16 When making a cut, use steady and 7. even pressure. Do not force cuts. Do not cut wet or warped lumber . 8. Hold the workpiece rmly with both 9. hands or use the included Push Stick.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 17 T o reduce possible injury should kickback occur , stand to side of the workpiece as it contacts the Blade. W ARNING! Do not stand in the line of cut. Once cut is made, turn off T able Saw .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 18 MAINTENANCE AND SER VICING Proceduresnotspecically explained in this manual must be performed only by a qualiedtechnician.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Rubber feet 4 2 Bolt M6×25 5 3 Spring washer 8 4 Mat washer 13 5 Base 1 7 Bolt ST4.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 20 P ARTS LIST Part Description Qty . 109 T able 1 1 10 Bolt M6×25 1 111 Bolt M6×35 1 1 12 T able insert 1 1 13 Blade Guard 1 1 14.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 21 ASSEMBL Y DIAGRAM.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 22 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and.
Een belangrijk punt na aankoop van elk apparaat Harbor Freight Tools 66630 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Harbor Freight Tools 66630 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Harbor Freight Tools 66630 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Harbor Freight Tools 66630 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Harbor Freight Tools 66630 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Harbor Freight Tools 66630 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Harbor Freight Tools 66630 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Harbor Freight Tools 66630 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
