Gebruiksaanwijzing /service van het product AVR 435 van de fabrikant Harman-Kardon
Ga naar pagina of 58
AVR 435 Power for the Digital Revolution ® A VR 435 Audio/ V ideo Receiver OWNER’S MANU AL.
2 T ABLE OF CONTENTS 3 Introduction 4 Safety Information 4 Unpacking 5 F ront P anel Controls 7 Rear P anel Connections 10 Main Remote Control Functions 14 Zone II Remote Control Functions 15 Installa.
INTRODUCTION 3 Introduction Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon A VR 435 you are about to begin many years of listening enjoyment.
4 INTRODUCTION / SAFETY INFORMA TION Introduction / Safety Information Preamp Outputs for Easy Expansion and Use with Future Audio Formats ■ Extensive bass management options , 6/8-channel direct in.
FRONT P ANEL CONTROLS 5 1 Main P ower Switch: Press this button to apply power to the A VR. When the switch is pressed in, the unit is placed in a Standby mode , as indicated by the orange LED 3 surrounding the System P ower Control 2 . T his button MUST be pressed in to operate the unit.
6 FRONT P ANEL CONTROLS Front P anel Controls 9 Surround Mode Selector: Press this button to cycle through the individual surround modes available after the Surr ound Mode Group Selector 5 was pressed (see item 5 above). Note that depending on the type of input, some modes are not always av ailable .
REAR P ANEL CONNECTIONS 7 Rear P anel Connections 230 V/50Hz .
8 REAR P ANEL CONNECTIONS Rear P anel Connections Video Monitor Outputs: Connect this jack to the composite and/or S-Video input of a TV monitor or video projector to view the on-screen menus and the output of any standard Video or S-Video source selected by the receiver’ s video switcher .
REAR P ANEL CONNECTIONS 9 Preamp Outputs: Connect these jacks to an optional, external power amplifier for appli- cations where higher power is desired. Surround Back/Multiroom Speak er Outputs: T hese speaker terminals are normally used to power the surround back left/surround back right speak ers in a 7.
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q 10 MAIN REMO TE CONTROL FUNCTIONS Main Remote Control Functions P ower Off But.
MAIN REMO TE CONTROL FUNCTIONS 11 Main Remote Control Functions IMPORT ANT NO TE: The A VR 435’ s remote may be programmed to control up to seven devices , including the A VR. Before using the remote, it is important to remember to press the Input Selector button 4 that corresponds to the unit you wish to operate .
12 MAIN REMO TE CONTROL FUNCTIONS K T uning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the T uner Mode but- ton I has been pressed or.
MAIN REMO TE CONTROL FUNCTIONS 13 Main Remote Control Functions VDI Button: T his button does not have any function for the A VR, but is provided for your use in programming the codes that are used to scroll up or down through the available inputs on your video display .
14 ZONE II REMO TE CONTROL FUNCTIONS Zone II Remote Control Functions å P ower Off ∫ A VR Selector ç AM/FM T uner Select ∂ Input Selectors ≠ T uning Up/Down – F ast Play ƒ Record/P ause © .
INST ALLATION AND CONNECTIONS 15 After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to mak e the connections to your audio and video equipment.
16 INST ALLATION AND CONNECTIONS Installation and Connections SCAR T A/V Connections F or the connections described above your video device needs RCA (cinch) connectors or/and S- Video connectors for .
INST ALLATION AND CONNECTIONS 17 Installation and Connections Black Y ellow Red Figure 1: SCART/Cinch-Adapter f or playbac k; signal flow: SCART → Cinch Black Red Blue Y ellow Green White Figure 2: .
18 INST ALLATION AND CONNECTIONS System and P ower Connections T he A VR 435 is designed for flexible use with multiroom systems , external control components and power amplifiers .
INST ALLATION AND CONNECTIONS 19 Installation and Connections T he A VR features a removable power cord that allows wires to be run to a complex installation so that the unit, itself , need not be installed until it is ready for connection.
20 SY STEM CONFIGURATION System Configuration Once the speak ers have been placed in the room and connected, the remaining steps are to pro- gram the system configur ation memories .
SY STEM CONFIGURATION 21 DVD . Note that once an input is selected, all set- tings for the Digital Input, Speak er Configuration and Surround Mode will ”attach” themselves to that input and be stored in a non-volatile memo- ry . T his means that once made, the selection of an input will automatically recall those settings .
22 SY STEM CONFIGURATION System Configuration sources are processed at their native sample rate . F or example, a 48kHz digital source will be processed at 48kHz. However , the A VR allows you to upsample the incoming 48kHz signals to 96kHz for added resolution.
SY STEM CONFIGURATION 23 Night Mode Settings T he Night mode is a feature of Dolby Digital that uses special processing to preserve the dynamic range and full intelligibility of a movie sound tr ack while reducing the peak level.
24 SY STEM CONFIGURATION System Configuration Y ou are now ready to start the EzSet/EQ process by following these steps: Step 1. Navigate to the EZSET/EQ MODE menu (Fig. 7) by first pressing the OSD Button L on the remote . Press the ¤ Navigation Button E until the ➔ cursor is pointing to EZSET/EQ in the MASTER MENU .
SY STEM CONFIGURATION 25 System Configuration Figure 7c Step 7a. If the measurements are not successful due to a missing or malfunctioning speak er , the FA R FIELD E Q ERROR message will appear as shown in Figure 7d.
26 SY STEM CONFIGURATION System Configuration Manual Setup In most cases it is simpler , easier and more accu- rate to let EzSet/EQ tak e care of entering the sys- tem parameters for speak er “size”, speak er crossover , channel output and individual channel delay time .
SY STEM CONFIGURATION 27 System Configuration If you are in doubt as to which setting best describes your speak ers consult the specifications in the speak ers’ owner’s manual, visit the speak- er manufacturer’ s web site or ask the dealer or installer from whom you purchased the speak ers.
28 SY STEM CONFIGURATION • If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speak ers, regardless of the type of program source or Surround mode you are listening to , press the ‹ / › Buttons E on the remote so that SU B L/R+LFE appears in the on-screen menu.
SY STEM CONFIGURATION 29 System Configuration T o assist in making these settings, the icons in the Speaker/Channel Input Indicators Ú will change as the speak er type is selected at each position. When only the inner icon box is lit, the speak er is set for “small.
30 SY STEM CONFIGURATION System Configuration When the delay settings are complete , press the ¤ Button E once so that the cursor is next to the BACK T O MANUAL SETUP menu line and press the Set Button p to return to the MANUAL SETUP menu.
SY STEM CONFIGURATION 31 System Configuration After checking for speak er placement, let the test noise circulate again, and listen to see which channels sound louder than the others . Using the front left speak er as a reference, press the ‹ / › Buttons E on the remote to bring all speak ers to the same volume level.
32 SY STEM CONFIGURATION System Configuration When all changes to the Channel Output levels and the associated level trim settings have been made press the ⁄ / ¤ Navigation Button E until the cursor is on the BACK T O MANUAL SETUP menu and then pressing the Set Button F so that you may mak e any other adjustments to the system parameters .
OPERA TION 33 Operation Surround Mode Chart MODE FEA TURES DELA Y TIME RANGE DOLBY DIGIT AL Available only with digital input sources encoded with Dolby Digital data. It provides Center: 0 - 30ft / 9m up to five separate main audio channels and a special dedicated Low F requency Effects Initial Setting: 12ft / 3.
34 OPERA TION Operation Surround Mode Chart MODE FEA TURES DELA Y TIME RANGE DTS Neo:6 Cinema T hese two modes are available when any analog source is playing to create a six-channel Delay time not adjustable DTS Neo:6 Music surround presentation from conventional Matrix-encoded and traditional Stereo sources .
OPERA TION 35 Operation Basic Operation Once you have completed the setup and configu- ration of the A VR, it is simple to oper ate and enjoy . T he following instructions should be fol- lowed for you.
36 OPERA TION Operation appear momentarily in the Main Information Display ˜ . To return the tone controls to an active condition, press the T one Mode 8 but- ton once or twice so that the words Tone I n momentarily appear in the Main Information Display ˜ .
OPERA TION 37 Operation of the demodulator to the Optical or Coaxial inputs *Ó of the A VR. No demodulator is required for use with DVD players or DTS- encoded laser discs .
38 OPERA TION Operation Selecting a Digital Source T o utilize either digital mode you must have properly connected a digital source to the A VR. Connect the digital outputs from DVD players , HDTV receivers , satellite systems or CD players to the Optical or Coaxial inputs on the rear or front panel *Ó .
OPERA TION 39 Operation indicators will light, as analog signals have only left and right channels . Digital signals , however , may have one , two , five , six or seven separate channels , depending on the program material, the method of transmission and the way in which it w as encoded.
40 OPERA TION Operation Output Level Adjustment With Sour ce Signals Normal output level adjustment for the A VR is established using the test tone, as out- lined on page 26. In some cases , however , it may be desirable to adjust the output levels using pro- gram material such as a test disc, or a selection you are familiar with.
ADV ANCED FEATURES 41 Advanced Featur es T he A VR is equipped with a number of advanced features that add extra flexibility to the unit’ s operation. While it is not necessary to use these features to operate the unit, they provide addi- tional options that you may wish to use .
42 ADV ANCED FEATURES / MUL TIROOM OPERA TION Advanced Featur es / Multiroom Operation T o turn off the semi-OSD system, you will need to mak e an adjustment in the ADVANCED SELECT menu (Figure 13). To start the adjust- ment, press the OSD button L to bring the MASTER MENU to the screen.
MUL TIROOM OPERA TION 43 Multiroom Oper ation Installation Although simple remote room systems may be installed by the average do-it-yourself hobbyist, the complexity of your multizone/multiroom sys- tem involves running wires inside of walls where the services of a specially trained installer may be required.
44 TUNER OPERA TION Multiroom Oper ation / T uner Operation and then press the ⁄ / ¤ Navigation Button E so that display changes to MULTI O N . Press the Set Button F again to activate the setting. Note that this method may be used to turn the Multiroom system on or off even when the A VR is in the Standby mode in the main lis- tening room.
TUNER OPERA TION 45 T uner Oper ation RDS Operation T he A VR is equipped with RDS (Radio Data System), which brings a wide range of informa- tion to FM radio .
46 PROGRAMMING THE REMOTE Configuring the Remote T he A VR 435 remote is factory-programmed for all functions needed to operate the unit. In addi- tion, it is also preprogrammed to oper ate most recent Harman Kardon DVD players and chang- ers , CD players and changers , CD recorders and cassette decks .
PROGRAMMING THE REMOTE 47 Progr amming the Remote Although the A VR remote is preprogrammed with an extensive library of codes for many major brands , it is also possible that you may have attempted to program a product that is too new or too old, and thus not all of its commands will be in the code library .
48 PROGRAMMING THE REMOTE Progr amming the Remote of the LCD screen, as shown in Figure 26. Press the Set Button F to begin the process of learning commands from another device’ s remote into the AVR remote . Figure 26 3. The SELECT A DEVICE message will appear in the LCD display (Figure 17).
PROGRAMMING THE REMOTE 49 Progr amming the Remote problem in doing that, but in normal operation the commands issued after selecting the VID 2 input are for a television, not a VCR. T he A VR remote allows you to correct that situa- tion through the “Changing Devices” process .
50 PROGRAMMING THE REMOTE Progr amming the Remote Buttons . Press the ⁄¤ Navigation Buttons E until the name of the button you wish to program the macro into is shown. F or this example we will show how to pro- gram a series of commands that will automat- ically be sent out every time the P ower button is pressed.
PROGRAMMING THE REMOTE 51 Progr amming the Remote 4. The next display screen (Figure 47) is where you select the macro to be read. Press the ⁄¤ Navigation Buttons E until the name of the macro you wish to read appears . F or this example, we will read back the Power On macro created in the previous section.
52 PROGRAMMING THE REMOTE Progr amming the Remote Figure 55 5. At the next display screen (Figure 56), you will select the device whose Channel Up/Down commands will be used. Press the ⁄¤ Navigation Buttons E until the desired device name appears to the right of the device in use .
PROGRAMMING THE REMOTE 53 Progr amming the Remote 4. The next display screen (Figure 68) is where you select the device that will be renamed. In our example , that is the TV button. Press the ⁄¤ Navigation Buttons E until the name of the base device appears and then press the Set Button F .
54 PROGRAMMING THE REMOTE Progr amming the Remote since the first letter we need to rename the T one button to Zoom is a “Z, ” so you would locate the “Z” above the “9” button, and press the button four times . T he first press shows a “W ,” the subsequent presses step through the other letters available until the “Z” appears .
PROGRAMMING THE REMOTE 55 Progr amming the Remote 4. Press the Set Button F one more time . T he LCD display will show the word SAVING on the top line for about 2 seconds and then flash SAVED four times on the bottom line to indicate that the setting has been accepted by the remote’ s memory .
56 TROUBLESHOO TING GUIDE T r oubleshooting Guide Processor Reset In the rare case where the unit’ s operation or the displays seem abnormal, the cause may involve the erratic oper ation of the system’ s memory or microprocessor . T o correct this problem, first unplug the unit from the AC wall outlet and w ait at least three minutes .
TECHNICAL SPECIFICA TIONS 57 T echnical Specifications Audio Section Stereo Mode Continuous Average P ower (FTC) 80 Watts per channel, 20Hz–20kHz, @ < 0.07% THD, both channels driven into 8 ohms 5/7 Channel Surround Modes P ower Per Individual Channel F ront L&R channels: 65 Watts per channel, @ < 0.
250 Crossways P ark Drive, Woodbury , New Y ork 11797 www .harmankardon.com Harman Consumer Group International: 2, route de Tours , 72500 Château-du-Loir , Fr ance © 2005 Harman Kardon, Incorporated P art No.
Een belangrijk punt na aankoop van elk apparaat Harman-Kardon AVR 435 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Harman-Kardon AVR 435 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Harman-Kardon AVR 435 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Harman-Kardon AVR 435 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Harman-Kardon AVR 435 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Harman-Kardon AVR 435 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Harman-Kardon AVR 435 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Harman-Kardon AVR 435 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
