Gebruiksaanwijzing /service van het product 10M van de fabrikant Hawking Technology
Ga naar pagina of 25
1.
FCC Warning This equipment has been tested and found to comply with the lim its for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable prot ection against harmful interference in a residen tial installation.
Unpacking the Switch 4 Introduction 1.1 General Description 5 1.2 Gigabit Ethernet Technology 5 1.3 Features 6 1.4 Front Panel 6 1.5 Rear Panel 7 Installation 2.1 Desktop Installation 8 2.2 Rack-Mount Installation 8 2.3 Installing Network Cables 9 2.4 Network Application 9 Description of Functions 3.
The complete HGS16S package consists of: • One HGS16S 16-Port 10/100/1000M Web-Smart Switch • Rack mount kit: 2 mounting brackets and screws • Four rubber feet with adhesive backing • One AC p.
1.1 General Description The device is a 16-port 10/100/1000Mbps Ethernet Web-Smart Switch. Compared with traditional 10/100Mbps Ethernet, the switch de livers a dedicated Gigabit connection to every attached client with no congestion issues.
1.3 Key Features • 16 fixed 10/100/1000Mbps Gigabit Ethernet ports • Provides Auto-discovery Function for easy network management • Provides 4K MAC address entries • 16 groups VLAN table • S.
Wiring for 10/100/1000Mbps (Copper) Below is the summary of the cabling required: Media Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Category 5 UTP/STP 10/100/1000Mbps copper 1000Mbps Category 5.
This switch can be placed directly on your desktop, on the floor, or mounted in a rack. Users can immediately use most of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to be put on a clean, flat desk or table close to a power outlet.
2.3 Installing Network Cables Station Connections Refer to the wiring statement of the previous section; connect each station/device to the switch with the correct cables. Switch-to-Switch Connections In making a switch-to-switch connection, using every po rt to connect another switch or backbone is stro ngly recommended.
3.1 PHY Monitoring and Port Mode Setup One of the software’s major tasks is to continuously monito r the PHYs in order to set up t he switch ports according to whether the link is up or down, and in the latter case, what the current speed, duplex mode and pause capabilities are.
This section instructs you on how to enter and set up the c onfigurations, whi ch can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Telnet sessi on / Internet Browser over the network (in-band). Factory Default value: IP: 192.
In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should co nfigure the managem ent station with an IP address and subnet mask compatible with your switch. 1. Run your Web Browser and enter the IP address “192.
4.2 Homepage On the Home page, you can select what you would like to config ure by clicking the menu tabs located at the top of the homepage. They include: • System • Ports • VLANS • Aggregati.
To restore the default values of switch, click the “ Default ” button at the top of the homepage. If you want to reboot the switch, click the “ Reboot ” Button. To check the connection status of each port, from 1 to 16, take a look at the port monitor.
4.2.1 System To set up the system configurations such as login values, time-out values, and for enabling the VLAN Management: Items Functions Mac Address The Mac Address of the switch S/W Version To look up the Software Version, see here. H/W Version The Hardware version Inactivity Timeout (Secs) Set the console inactivity timeout in seconds.
Note: After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP Address with your browser. 4.2.2 Ports On this page, you can view the port status, set up the speed “Mode” and enable the “FDX Flow Control”.
Items Functions Link Shows the status of each port. When it is red, it means the connection is down. Otherwise, it is green. Mode Choose the Speed mode of port: 10/100/1000, Half/Full. To disable the port, choose “Disable”. If you set to auto-speed, it will be auto- negotiation.
PVID When the VLAN-enabled switch receives a ta gged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Functions Port Port Number 1~16 PVID Port VLAN ID Aware To enable the PVID checking and inserting of one port, select “AWARE” Only Tagged Block the untagged frame.
19.
4.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, put the port numbers into the same Aggregation group line . There are eight groups that can be made. Do not forget to click the “Apply” to save th e settings. The m aximum number of ports for one group is 8.
4.2.5 QoS There is one mode of Quality of Service to choose: custom TOS. 4.2.5.1 Custom ToS To improve the network performance by applying the TOS, set up the priority of eight groups of precedence bits on this page. There are two types to choose, high or Low.
4.2.6 Mirror Port mirror is used to mirror traffic from a source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simultaneously to 1 Monito r port (target port).
4.2.7 Statistics To check the status of port traffic, click the “Statistic” tab. You can click the “ Clear ” button to erase all records or click “ Refresh ” to show the most current status.
4.2.9 Default To restore to default values, 1. Click the default button on the homepage. 2. Click “Yes” to restore default values. Do not power off the switch while it is working. 4.2.10 Reboot To reboot the switch, 1. Click the “Reboot” button on the homepage 2.
Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN interoperability IEEE802.
Een belangrijk punt na aankoop van elk apparaat Hawking Technology 10M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hawking Technology 10M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hawking Technology 10M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hawking Technology 10M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hawking Technology 10M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hawking Technology 10M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hawking Technology 10M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hawking Technology 10M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
