Gebruiksaanwijzing /service van het product DB-200H van de fabrikant Hoshizaki
Ga naar pagina of 19
™ INSTRUCTION MANUAL ISSUED: JUNE 5, 2001 DB-200H ICE DISPENSING BIN R eliability is a beautiful thing TM REVISED: DEC. 10, 2003.
2 IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT Only qualified service technicians should attempt to install, service or maintain this ice dispenser. No installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual.
3 • Please review this manual. It should be read carefully before the ice dispenser is installed and operated. Only qualified service technicians should install, service and maintain the ice dispenser. This manual should be made available to the technician prior to installation, maintenance or service.
4 We reserve the right to make changes in specifications and design without prior notice. See NAMEPLATE for electrical specifications. The nameplate is located on the upper part of the Right Side Panel. I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I.
5 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with.
6 [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M.
7 [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_,.
8 II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS 1. CHECKS BEFORE INSTALLATION 1.
9 WARNING WARNING WARNING WARNING WARNING This ice dispensing bin is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F. To the icemaker, water temperature should be within +45°F to +90°F. Extended periods of operation at temperatures outside of these limitations may cause unsatisfactory results.
10 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. CAUTION CAUTION CAUTION CAUTION CAUTION It is especially important that the icemaker/ice dispensing bin is leveled in both left-to-right and front-to-rear directions.
11 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 *Note: With KML models, Top Panels are not necessary..
12 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION WARNING WARNING WARNING WARNING WARNING 1. Electrical connection must be made in accordance with the instructions on a “WARNING” tag, provided with the pig tail leads in the Junction Box.
13 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 1. A drain outlet, 3/4" FPT, is located at the rear of the ice dispensing bin.
14 Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection.
15 7. START UP 7. START UP 7. START UP 7. START UP 7. START UP 1) Start up the icemaker. See the “START UP” instructions on the icemaker. 2) Allow at least three (3) cycles of ice production, and then place a proper container in the ice station. 3) Push the ice dispensing switch to dispense ice cubes.
16 III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III.
17 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Agitator Agitator Agitator Agitator Agitator Spout of the Spout of the S.
18 7) Scrub the Shutter Assembly and Spout—after removing them—using the cleaning solution of item 6. See Fig. 5. a) Remove the Snap Pin fitted to the Shutter Shaft and shift the Shaft to the left. Then the Shutter Assembly can be removed from the bin.
19 91A4JB10C HOSHIZAKI HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 .
Een belangrijk punt na aankoop van elk apparaat Hoshizaki DB-200H (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hoshizaki DB-200H heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hoshizaki DB-200H vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hoshizaki DB-200H leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hoshizaki DB-200H krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hoshizaki DB-200H bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hoshizaki DB-200H kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hoshizaki DB-200H . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
