Gebruiksaanwijzing /service van het product GF641 van de fabrikant Hotpoint
Ga naar pagina of 16
Instructions for Installation and Use Gas Hob Model GF640 - GF 641.
2 CONTENTS Introduction For Your Safety Know your Hob How to use your Hob Practical Advice Care and Cleaning Troubleshooting Installation Electrical Connection Characteristics of Burners and Nozzels A.
3 Y our new hob is guaranteed* and will giv e lasting ser vice. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions detailed in this booklet. To help make best use of your cooking equipment, please read this booklet carefully.
4 For Y our Safety AL W A YS: - make sure you remove all packaging and dispose of saf ely . - check the soundness of the appliance after it has been unpacked. - make sure you understand the controls before using the appliance. - keep children away from the appliance during use.
5 D F A B C E A. Gas Burners B. Pan Support for Cookware C. Control Knobs for Gas Burners D. Ignitor for Gas Burners E. Ignition Button for Gas Burner s (only on cer tain models) F. Flame Failure Device - Activates if the flame accidentally goes out (spills, drafts, etc.
6 Practical Advise on Using the Burners For best performance, follow these general guidelines: • Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching .
7 Care and Cleaning Troubleshooting If the burner does not remain on when set to "Low". Check to make sure that: • The gas holes are not clogged. • There are no draughts near the cooking surface. • The minimum has been adjusted correctly (see Installation section, "Minimum Regulation").
8 Installation The following instructions are intended for the installer so that the installation and maintenance procedures may be followed in the most professional and expert manner possible. Important: Disconnect the appliance from the electrical suppl y before performing any maintenance or repair.
9 Gas Connection for the Hob The hob should be connected to the gas supply by an authorized installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing.
10 Adapting the Hob for Different Types of Gas To adapt the hob to a different type of gas than that for which it was designed, (see the sticker under the hob or on the packaging), the burner nozzles must be changed, as follows: • Remove the pan supports and slide the burners out of the cooktop .
11 Electrical Connection Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED. The hob is designed to work with alternating current, the supply voltage and frequency indicated on the rating plate (situated under the hob). Make sure that the local supply voltage corresponds to the voltage indicated on the rating plate.
12 Characteristic of the burners and nozzles T a bl e 1 Liquid G a s N a tur a l G a s Burner Diameter (mm) Thermal P ower kW (p .c.s.*) By-pass 1/100 (mm) Noz zle 1/100 Flow* g/h Noz zle r 1/100 Flow* l/h Nom. Red . (1 ) (mm) *** ** (mm) Fa s t (Large) (R ) 100 3.
13 Notes.
GB 14 "No company is better positioned to offer an after sales service on a Hotpoint appliance than us - the manufacturer" As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months.
GB 15 Guarantee "Satisfaction guaranteed or your money back" We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www.
0 9 -200 5 P a r t n o . FP162 - 01 Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and services we offer. Repair Service and Information Desk UK: 08709 066 066 (Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays) www.
Een belangrijk punt na aankoop van elk apparaat Hotpoint GF641 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hotpoint GF641 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hotpoint GF641 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hotpoint GF641 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hotpoint GF641 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hotpoint GF641 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hotpoint GF641 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hotpoint GF641 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
