Gebruiksaanwijzing /service van het product HP E5123A van de fabrikant HP (Hewlett-Packard)
Ga naar pagina of 24
H Broadband Service Analyzer Setting Up the STM-1 Electrical Interface Pod.
The information contained in this document is subject to change without notice. HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
iii Contents Guide to the HP E5200A Broadband Service Analyzer Documentation ........ iv About the STM-1 Electrical Interface Pod ....................................................... 1 Online Help ...................................................
Guide to the HP E5200A Broadband Service Analyzer Documentation iv Guide to the HP E5200A Broadband Service Analyzer Documentation The HP E5200A Broadband Service Analyzer comes with a comprehensive set of paper and online documentation. Use the following table to determine which documents you should use.
1 About the STM-1 Electrical Interface Pod About the STM-1 Electrical Interface Pod Overview The HP E5123A STM-1 Electrical Interface Pod is a self-contained, plug-in module. Y ou use it in conjunction with the HP E5200A Broadband Service Analyzer to test and analyze a system under test (SUT).
Online Help 2 Online Help The User Online Help provides all the information you need to use the analyzer . Use the following sections to learn how to perform tasks : • Getting started • Monitoring.
3 Front Panel at a Glance Front Panel at a Glance Access (green LED) Lights each time the interface pod is accessed by the network. Signal (yellow LED) Lights when a valid signal is present at the input connector. In (BNC) Accepts an electrical signal from the SUT.
To Set Up the Interface Pod 4 T o Set Up the Interface Pod Caution Handle the interface pod with care to avoid electrostatic discharge (ESD) damage during unpacking, installation, and operation. The connectors on the front and rear of the interface pod are susceptible to ESD.
5 To Set Up the Interface Pod T o Insert the Interface Pod Y ou can insert and remove interface pods at any time, even when the analyzer is powered on. Initially , you insert an interface pod when you set up the analyzer. Subsequently , you insert an interface pod when you change the physical layer interface that you want to monitor .
To Set Up the Interface Pod 6 T o Remove the Interface Pod When you remove the interface pod, make sure you store it in a dust free location that meets the environmental requirements listed in “Environmental Specifications” on page 13. An electrostatic-safe bag has been supplied for the storage of each interface pod.
7 To Set Up the Interface Pod Common system connections and test connections are • non-intrusive system connection—T -piece and passive test connections • intrusive system connection—network e.
To Set Up the Interface Pod 8 Automatic Configuration Parameters After you insert the interface pod and connect it to the SUT , the analyzer automatically configures to the STM-1 electrical signal.
9 To Set Up the Interface Pod T o Manually Configure the Interface Pod Note When the configuration is complete, the analyzer updates all relevant screens and windows to reflect the new configuration parameters. 1 From the Configure menu, select the appropriate port; then select Set Up.
What to Do Next 10 What to Do Next The interface pod is now ready for use. See the User Online Help to find out the different tasks you can perform using the analyzer and interface pod.
11 Standards and Specifications Standards and Specifications Communications Standards ITU-T G.703 Physical/Electrical Characteristics of Hierarchical Digital Interfaces ITU-T G.708 Network Node Interface for the Synchronous Digital Hierarchy ITU-T G.
Standards and Specifications 12 Input and Output Specifications T ransmit Levels Receive Levels Parameter Nominal Min. Max. Notes Signal level 1.0 V (pp) 0.9 V (pp) 1.1 V (pp) complies with ITU-T G.703 Line rate 155.52 Mb/s –4.6 ppm +4.6 ppm using internal frequency reference Line jitter complies with ITU-T G.
13 Standards and Specifications Physical Specifications Environmental Specifications Error Generation Specifications Weight 1.0 kg ( 2.2 lbs) (nominal) Dimensions Height: 44 mm (1.73 inches) Width: 149 mm (5.87 inches) Length: 222 mm (8.74 inches) not including front panel connectors 236 mm (9.
Certification Hewlett Packard Australia Ltd certifies that this product met its published specifications at the time of shipment from the factory. Hewlett-Packard (HP) further certifies that its calibration measurements are traceable to the extent allowed by the calibration facilities of other International Standards Organization members.
Warnings The following general safety precau- tions must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety stan- dards of design, manufacture, and intended use of the product.
Avertissement Cet appareil répond aux normes de la “Classe de sécurité 1” et est muni d’un fil de mise à la terre pour votre protection. Pour prévenir les risques de choc élec- trique, la broche de mise à la terre du cordon d’alimentation ne doit pas être dés- activée.
page inner margin hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line outer margin for text and artwork Right body text drop top margin .
body text drop hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line inner margin for text and artwork page inner margin Left top margin f.
page inner margin hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line outer margin for text and artwork Right body text drop top margin .
body text drop hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line inner margin for text and artwork page inner margin Left top margin f.
Een belangrijk punt na aankoop van elk apparaat HP (Hewlett-Packard) HP E5123A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen HP (Hewlett-Packard) HP E5123A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens HP (Hewlett-Packard) HP E5123A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding HP (Hewlett-Packard) HP E5123A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over HP (Hewlett-Packard) HP E5123A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van HP (Hewlett-Packard) HP E5123A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de HP (Hewlett-Packard) HP E5123A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met HP (Hewlett-Packard) HP E5123A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
