Gebruiksaanwijzing /service van het product 89025 van de fabrikant Huffy
Ga naar pagina of 22
1 06/03 P/N 211543B Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any IMPORT ANT! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, problems may occur.
P/N 211543B 06/03 2 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
3 06/03 P/N 211543B 2 3 4 8 7 Assemble rims as shown below . 1 3. 5. 4. RIM ASSEMBL Y - Corner Locations 1 and 2.
P/N 211543B 06/03 4 6. W ARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown.
5 06/03 P/N 211543B Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 7.
P/N 211543B 06/03 6 At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure the display pole (11), slide the display wedge (12) into position as shown. Tighten the set screw (13) to lock the display pole (11) in place.
7 06/03 P/N 211543B 8 11 49 16 10. 11 . 17 30 24 52 51 49 30 12. 49 8 55 54 54 57 44 57 55 13. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. Tighten flange nuts (8) completely. Attach spacers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
P/N 211543B 06/03 8 37 14. 38 38 24 24 17 17 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 8 8 15. 59 27 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown .
9 06/03 P/N 211543B 17. 16. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support brackets (37) using sp acers (59), bolt (27), and nut (42) as shown. Attach backboard assembly to pole section (1 1). Install pole cap (43). NOTE: T wo people are recommended for this step.
P/N 211543B 06/03 10 19. 55 18. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55).
11 06/03 P/N 211543B 27 59 59 42 21. 29 29 23 8 8 29 REFER TO INSTRUCTIONS INCLUDED WITH RIM HARDWARE FOR RIM ASSEMBLY 23 22. Attach lower elevator tubes (29) to backboard bracket s (23) using spacers (59) bolt (27) and nut (42) as shown.
P/N 211543B 06/03 12 27 21 42 21 22 22 23. 42 21 21 27 27 29 42 43 24. Attach backboard assembly to pole section (1 1). Then install pole cap (43). NOTE: T wo people are recommended for this step.
13 06/03 P/N 211543B 42 27 29 29 47 59 59 26. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). 55 A C B T o Set Backboard Height: A. While holding handle, remove pin (55).
P/N 211543B 06/03 14 1. Attach elevator bracket (36) and reinforcement bracket (41) to pole section (1 1) using bolts (16) and nuts (8) as shown. 41 11 36 16 8 23 23 17 65 15 15 24 18 2.
15 06/03 P/N 211543B Bend top of backboard brackets (23) outward to match up with holes on backboard and secure using nuts (8) and bolt s as shown. Attach rim to backboard using using bolts and nut s (8) as shown. 27 60 60 42 3. 29 29 23 8 58 8 8 29 4.
P/N 211543B 06/03 16 20 21 42 21 56 56 5. 6. Attach upper elevator tubes (21) to backboard bracket s (23) using spacers (56) bolt (20) and nut (42) as shown. Attach backboard assembly to top pole section (1 1). Then install pole cap (43). NOTE: Tw o people are recommended for this step.
17 06/03 P/N 211543B 5 6 6 31 28 5 31 7. Fig. A Fig. B 6 Insert locking pin (28) into bracket on adjustment tube (6). Insert cross pin (5) through hole in bracket and locking pin (28) as shown in figure A.
P/N 211543B 06/03 18 28 6 31 53 28 50 31 53 8. Fig. C Insert spring (53) into back of locking pin (28) as shown. S pring (53) should rest between two small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (50) into bracket on the adjustment tube (6) as shown.
19 06/03 P/N 211543B 27 59 59 6 42 61 61 61 61 61 9. 10. 11 . 64 63 36 62 62 6 29 Attach adjustment tube to lower elevator tubes using bolt spacers and nut as shown.
P/N 211543B 06/03 20 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble 40” fan backboard as shown below with a st andard rim as shown. 40” F AN BACKBOARD ASSEMBL Y - Corner Location 4.
21 06/03 P/N 211543B Item #26 (2) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 1 200215 Cross Pin 6 1 900006 Adjustment Tube - Upper 7 16* 203113 Bolt, Hex-Flange 5/16-18 x 2.
P/N 211543B 06/03 22 Item #27 (13) Item #18 (2) Item #20 (2) Item #33 (24) Item #35 (6) 22 of 22 Item #30 (8) Item #39 (4)* Item #40 (2) Item #59 (8) Item #60 (2) HARDW ARE IDENTIFIER (BOL TS & SC.
Een belangrijk punt na aankoop van elk apparaat Huffy 89025 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Huffy 89025 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Huffy 89025 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Huffy 89025 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Huffy 89025 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Huffy 89025 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Huffy 89025 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Huffy 89025 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
