Gebruiksaanwijzing /service van het product 89225 van de fabrikant Huffy
Ga naar pagina of 20
1 P/N 21154401 01/04 IMPORT ANT! T o ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display T echnician at 1-800-558-5234.
P/N 21154401 01/04 2 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
3 P/N 21154401 01/04 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE T O ASSEMBLERS AL L Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
P/N 21154401 01/04 4 P A R TS LIST (See Hardware Identifier) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 2 201651 Spacer, .50 I.D. x .25 Long 6 2 206303 Washer, 1/4" Flat 7 8* 203113 Bolt, Hex-Flange 5/16-18 x 2.
5 P/N 21154401 01/04 Item #33 (12) Item #30 (4) Item #40 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #67 (2) PLASTIC SP ACERS Item #7 (10) Item #4 (2) Item #22 (2) Item #13 (2) Item #27 (5) It.
P/N 21154401 01/04 6 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
7 P/N 21154401 01/04 At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required, secure the display pole by sliding the display wedge (12) into position as shown. T o lock the display pole in place, tighten the set screw (13 or 39).
P/N 21154401 01/04 8 8 11 49 16 1. 2. 17 30 24 52 51 49 30 3. 49 8 55 54 54 57 44 57 55 4. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. T ighten flange nuts (8) completely . Attach sp acers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
9 P/N 21154401 01/04 STEEL FRAME A CR YLIC BACKBOARD ASSEMBL Y - Corner Location 1 37 5. 38 38 24 24 17 17 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown . 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly .
P/N 21154401 01/04 10 7. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support bracket s (37) using spacers (59), bolt (27), and nut (42) as shown. 8. Attach backboard assembly to pole section (1 1). Install pole cap (43). 42 21 43 21 29 29 27 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY.
11 P/N 21154401 01/04 10. 9. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). Attach adjustment rod (47) to lower elevator tubes (29) using bolt (27) spacer (59) and nut (42) as shown.
P/N 21154401 01/04 12 3 35 22 4 58 1 2 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2).
13 P/N 21154401 01/04 44” F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 2 Correctly identify each pole section. ONL Y THE T OP POLE SECTION (14) IS USED IN THIS ASSEMBL Y . 1. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 Fit spacer (15) into p awl (19).
P/N 21154401 01/04 14 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolt s (20), spacers (5, & 40), and nut s (42) as shown. T ighten completely . 5 . Secure pawl (19) in place with clevis pin (31) and washers (6) as shown.
15 P/N 21154401 01/04 7. Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nut s (8).
P/N 21154401 01/04 16 20 20 41 9. Attach upper and lower elevator tubes (21) to top pole section (14) using bolt s (20) and nuts (42) as shown. Attach pole cap (41) as shown. 42 21 21 21 21 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown.
17 P/N 21154401 01/04 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ONL Y THE T OP POLE SECTION (50) IS USED IN THIS ASSEMBL Y . F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 3.
P/N 21154401 01/04 18 F AN BACKBOARD ASSEMBL Y - Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1.
19 P/N 21154401 01/04 Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
P/N 21154401 01/04 20 Install net. Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip.
Een belangrijk punt na aankoop van elk apparaat Huffy 89225 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Huffy 89225 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Huffy 89225 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Huffy 89225 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Huffy 89225 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Huffy 89225 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Huffy 89225 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Huffy 89225 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
