Gebruiksaanwijzing /service van het product DH9300 van de fabrikant Huffy
Ga naar pagina of 35
1 05/03 P/N 211689C © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211689C 05/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
05/03 P/N 211689C 3 W ARNING F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or an y par t of the system including bac kboard, support braces or net.
4 P/N 211689C 05/03 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE TO ASSEMBLERS AL L Huffy Sport s basketball systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to instructions.
05/03 P/N 211689C 5 Get to know the basic parts of your basketball system..... FRONT T OP POLE BACK MIDDLE POLE FRONT COVER RIM BOTTOM POLE STRUTS ELEV A T OR ASSEMBL Y BACKBOARD BASE WHEEL CARRIAGE A.
6 P/N 211689C 05/03 Item Qty Part No Description 1 1 900467 Top Pole Section 2 1 904811 Middle Pole Section (with Label) 3 1 903407 Bottom Pole Section 4 2 900223 Wheel Bracket 5 2 206940 Axle 6 2 226403 Wheel 6” 7 4 206938 Pushnut 8 1 200117 Base 9 1 203223 Carriage Bolt, 5/16-18 x 1 10 1 202662 Hex Bolt, 5/16-18 x 4.
05/03 P/N 211689C 7 HARDW ARE IDENTIFIER Item #7 (2) Item #10 (1) Item #1 1 (7) Item #15 (1) Item #19 (1) Item #20 (5) Item #21 (1) Item #22 (16) Item #23 (1) Item #26 (4) Item #32 (4) Item #37 (9) It.
8 P/N 211689C 05/03 202052 02/03 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. Rotate handle forw ard until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5.
05/03 P/N 211689C 9 SECTION A : ASSEMBLE THE POLES 2. 1. Wood Scrap 2 1 5" (13 cm) 5" (13 cm) 1 3 2 Correctly identify each pole section. Mark pole sections with t ape as shown. T APE T APE Bounce middle pole section (2) into top pole section (1) together using a wood scrap as shown until they no longer move toward taped reference mark.
10 P/N 211689C 05/03 IMPORT ANT! Holes in top (1) and bottom pole (3) sections MUST align to correctly position elevator system toward playing surface. While maintaining alignment, bounce assembly and lower section (3) together as shown until they no longer move toward taped reference mark.
05/03 P/N 211689C 11 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE 1/2” & 9/16” 9/16” & 1/2” AND EXTENSION HAMMER OR MAL.
12 P/N 211689C 05/03 1. 2. Insert axle (5) through wheel bracket (4). Secure wheels (65) to axle using pushnuts (7). Carefully t ap pushnuts onto axle with hammer or mallet 4 65 65 7 7 5 Install wheel assembly to base (8) using bolt (9), and nut (22) as shown.
05/03 P/N 211689C 13 3. Install rod (12) through holes in bottom pole section (3) and eyebolt (13). Insert pole assembly into tank (8) and through center hole on wheel assembly as shown. Secure pole assembly with anchor strap (56), washer (1 1), and lock nut 13 12 1 3 2 48 12 13 8 11 56 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
14 P/N 211689C 05/03 4. 10 11 11 45 14 3 15 14 14 Secure tank struts (14) to pole as shown. Place cap (15) over exposed end of bolt as shown. Rotate non-secured ends of tank struts (14) outward to mounting holes in tank as shown. TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
05/03 P/N 211689C 15 5. 6. Secure ends of tank struts (14) to tank as shown. Repeat for opposite side. Install upper pivot bracket (16) to front of base using bolt (19), washer (20) and nut (48) as shown. 43 11 22 11 14 48 20 16 19 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
16 P/N 211689C 05/03 Insert bolt (21) through lower pivot bracket (17) as shown; bolt (21) will be secured during step 10. Carefully place base assembly on it s side. Install lower pivot bracket (17) with bolt (23), washers (20), and lock nut (48) as shown.
05/03 P/N 211689C 17 Install wheels (6) onto axle (5) and wheel bracket (4) with push caps (7) as shown. Position base as shown. Secure wheel bracket assembly with disc (64), washer (20) and nut (48) as shown. 7 6 5 4 6 7 21 64 20 48 Carefully reposition entire assembly as shown.
18 P/N 211689C 05/03 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEV A T OR SYSTEM & BACKBOARD (2) 1/2”, (2) 3/4” AND (2) 9/16” .
05/03 P/N 211689C 19 60 59 25 58 24 Slide shroud (25) back to expose bracket and assemble gas strut components as shown. Do not over-tighten. Carefully place end of cable into slot on bracket (24) as shown. Install strut shroud (25) over strut assembly as shown.
20 P/N 211689C 05/03 58 62 61 28 27 63 Attach plastic lever (63) to height adjustment shroud (27) with bolt (62) and nut (58) as shown. Attach height label (61) to the front of the elevator adjustment tube 1 1” down from top of the elevator adjustment tube (28) as shown.
05/03 P/N 211689C 21 6. 28 Remove nuts from free end of cable. Insert cable into height adjustment tube as shown (FIG . A ) . Pull cable through end of tube (FIG . B) . FIG . B FIG . A 7. Install pole bracket (36) to top pole as shown (FIG .A ) . Reference finished assembly (FIG .
22 P/N 211689C 05/03 1 34 35 37 37 35 39 35 35 33 41 40 40 8. Identify elevator tubes. Install triangle plates (33) and elevator tubes (35) to top pole section (1) as shown. Install pole cap (34) at this time. 33 Test-fit bolts into holes; carefully rock them in a circular motion to ream out paint from holes if necessary.
05/03 P/N 211689C 23 37 42 42 40 40 40 37 9. 10. Attach elevator adjustment tube (28) to elevator tubes (35) with bolts (40) spacers (42) and nuts (37) as shown.
24 P/N 211689C 05/03 37 40 11 . Attach front of gas strut assembly to elevator tubes (35) by rot ating elevator tubes (35) and inserting bolt (40) and nut (37) as shown. T O A VOID RAPID EXTENSION OF STRUT ROD - DO NOT DEPRESS BUTTON ON GAS STRUT ASSEMBL Y .
05/03 P/N 211689C 25 49 46 46 47 47 48 48 Assemble brackets (49) to backboard using bolts (47) spacers (46) and nut s (48) as shown. The spacers may fit very tightly between the brackets and may need to be t apped into place with a hammer . 13. 43 45 12.
26 P/N 211689C 05/03 40 35 35 42 42 49 37 Assemble lower elevator tubes (35) and rim to brackets (49) using bolt (40), spacers (42), and nut (37) as shown. 14. IMPORT ANT!: Refer T o Instructions Included With Rim Hardware For Rim Assembly . Use the 5/16-18 x 1" hex-flange bolt s for inst alling rim to the acrylic backboard.
05/03 P/N 211689C 27 35 35 40 42 49 37 42 Assemble upper elevator tubes (35) to brackets using bolt (40), spacers (42), and nut (37) as shown. 15..
28 P/N 211689C 05/03 SECTION D: INST ALL FRONT COVER & HANDLE 1. Attach front cover (50) to hinge tubes (18) using carriage bolt (61) and flange nuts (15) as shown.
05/03 P/N 211689C 29 29 28 29 28 3. Install trigger (29) onto cable as shown. 28 44 2. Re-install nuts and washer as shown. It is very important to leave 1/8” of exposed thread on cable as shown.
30 P/N 211689C 05/03 31 29 30 32 4. Install handle (30) to height adjustment assembly with screws (32) as shown. Be sure washer is seated in slot on handle as shown (FIG .
05/03 P/N 211689C 31 1. SECTION E: INST ALL NET CLIPS AND NET W ARNING: Use of this product without proper inst allation of net clip s, or when all net clip s are not present could result in bodily harm. Be sure to follow directions carefully . Install net clips.
32 P/N 211689C 05/03 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 2.
05/03 P/N 211689C 33 1. SECTION F: SECURING THE SYSTEM Roll assembly to desired playing area. Secure assembly to ground using strap (56) and tie down st ake (55). Fill base (8) with water (approx. 40 gallons) and snap fill cap (54) in place. 56 54 55 8 DO NOT LEA VE ASSEMBL Y UN A TTENDED WHEN EMPTY , IT M A Y TIP OVER.
34 P/N 211689C 05/03 202052 02/03 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. Rotate handle forw ard until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5.
05/03 P/N 211689C 35 59 SECTION H: TROUBLESHOOTING GUIDE 1. If the elevator is still difficult to operate, verify that the valve located on the strut is fully depressed when the trigger is activated. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
Een belangrijk punt na aankoop van elk apparaat Huffy DH9300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Huffy DH9300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Huffy DH9300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Huffy DH9300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Huffy DH9300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Huffy DH9300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Huffy DH9300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Huffy DH9300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
