Gebruiksaanwijzing /service van het product M671111 van de fabrikant Huffy
Ga naar pagina of 25
1 07/05 ID# M671111 © COPYRIGHT 2005 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 ID# M671111 07/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
07/05 ID# M671111 3 Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
4 ID# M671111 07/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
07/05 ID# M671111 5 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
6 ID# M671111 07/05 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE.
07/05 ID# M671111 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 203470 Washer, Flat, 1.5” O.D. 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4 1 908006 To.
8 ID# M671111 07/05 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. #7 (2) #40 (1) #39 (2) Item #23 (1) #29 (6) #16 (2) #12 (1) #44 (4)* #19 (4) #47 (4) #49 (1) .
07/05 ID# M671111 9 HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) HARDW ARE IDENTIFIER (OTHER) #13 (2) #20 (2) #26 (4) #30 (4) #36 (2) #1 1(4)* #1.
10 ID# M671111 07/05 T OOLS REQUIRED FOR THIS SECTION SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finished this section: 1/2” 9/16” Wrenches (2) 1/2.
07/05 ID# M671111 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 .
12 ID# M671111 07/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 203100.
07/05 ID# M671111 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
14 ID# M671111 07/05 4. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH TROUGH TROUGH Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown.
07/05 ID# M671111 15 9 7 6 9 7 13 8 45 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 7. Secure cover to rod (9) using washers (45) nuts (8) and nut covers (13) as shown.
16 ID# M671111 07/05 8 . Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 42 14 14 15 16 16 9. Att ach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (8) as shown.
07/05 ID# M671111 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly .
18 ID# M671111 07/05 TOOLS REQUIRED FOR THIS SECTION SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look like when you’ve finished this section: W renche.
07/05 ID# M671111 19 Assemble backboard brackets (27) using bolt s (43), and nuts (8) as shown. 1. 27 43 8 8 43.
20 ID# M671111 07/05 2. Attach lower elevator tubes (32) and counter balance springs (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown.
07/05 ID# M671111 21 3. 50 52 1 48 49 Inst all Slam Jam Rim to Backboard 34 51 49 1 52 A B C D E A Fit rim (34) securely into bracket (48) as shown. Allow T -bolt (49) to slip through center hole in rim (34). B Install reinforcement bracket (50) onto T -bolt (49) as shown.
22 ID# M671111 07/05 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1), bolt (29), and nut (31) as shown.
07/05 ID# M671111 23 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 5. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 6. 7.
24 ID# M671111 07/05 8. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 9. Roll completed assembly to desired position.
07/05 ID# M671111 25 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height.
Een belangrijk punt na aankoop van elk apparaat Huffy M671111 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Huffy M671111 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Huffy M671111 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Huffy M671111 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Huffy M671111 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Huffy M671111 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Huffy M671111 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Huffy M671111 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
