Gebruiksaanwijzing /service van het product N53 W24700 van de fabrikant Huffy
Ga naar pagina of 26
09/04 P/N 211574 1 Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632-792 Internet Address: www.
2 P/N 211574 09/04 W ARNING F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or an y par t of the system including bac kboard, suppor t braces or net.
09/04 P/N 211574 3 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s basketball systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to instructions.
4 P/N 211574 09/04 WARRANTY CARD: Please remember to complete your product registration form either on-line at: www.huffysports.com/warrantycard or mail-in the enclosed postcard .
09/04 P/N 211574 5 HARDWARE IDENTIFIER (CONTINUED) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #5 (1) Item #21 (1) Item #19 (1) Item #65 (1) Item #54 (3) Item #23 (1) Item #10 (1) Item #36 (1) Ite.
6 P/N 211574 09/04 * You may have extra parts with this model. HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (STEEL SP ACERS, RODS & CLIPS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS.
09/04 P/N 211574 7 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
8 P/N 211574 09/04 1. 5" (13 cm) MIDDLE TO P 5" (13 cm) BO TT OM 2 3 1 Identify pole sections. ID Sticker ID Sticker 2. WOOD SCRAP (NOT SUPPLIED) 2 1 While maintaining alignment, bounce midd.
09/04 P/N 211574 9 3. 1 2 3 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH Align dimple of middle pole section (2) into trough of bottom pole section (3) as shown. IMPORT ANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP.
10 P/N 211574 09/04 4. 5. Install wheels (17) onto axle (28) and wheel bracket (25) with push cap s (29) as shown. Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15) as shown.
09/04 P/N 211574 11 6. Install rod (4) through holes in bottom pole section (3) and eyebolt (5). Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure pole assembly with strap (44), washer (1 1) and lock nut (8).
12 P/N 211574 09/04 7. 9 9 Secure base struts (9) to pole using bolt (10) washers (1 1) and nut (12) as shown. Rotate the non-secured ends of base strut s (9) as shown. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
09/04 P/N 211574 13 8. 9. Secure base struts (9) to base using bolt (14) washers (1 1) and nut (15). Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut (8) as shown. 14 11 15 11 9 8 20 18 19 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
14 P/N 211574 09/04 Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 13. Carefully place base assembly on its side. Inst all lower pivot bracket (22) with bolt (23), washers (20) and lock nut (8) as shown.
09/04 P/N 211574 15 Position base as shown. Secure wheel bracket assembly with disc (30), washer (20) and nut (8) as shown. 29 27 28 25 27 29 21 30 20 8 Carefully reposition entire assembly as shown: 12. 13. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET.
16 P/N 211574 09/04 15 . Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolt s (46) as shown. T ighten flange nuts (15) completely . 16. Attach sp acers (32, 33) to pole mount bracket (45) with bolts (54), washers (20), and lock nuts (37) as shown.
09/04 P/N 211574 17 17 . 45 15 35 48 48 34 50 Apply logo and height indicator labels (41) to adjustment rod (31) as shown. Att ach handle part s (38, 39) to adjustment rod with screw (36), carriage bolts (26), and flange nut s (15) as shown. 18 . 26 15 15 39 38 36 26 31 41 41 Assemble lanyard (34) to locking pin (35) as shown (FIG A).
18 P/N 211574 09/04 53 51 37 52 55 54 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (35). 35 19 . 20. Install sp acers (51) onto backboard brackets (52), with bolt s (53, 54) and lock nuts (55, 37) as shown.
09/04 P/N 211574 19 58 59 57 56 52 21. 63 Upper Elevator tube T oward Pole T oward Board 56 Lower Elevator tube T oward Pole T oward Board Identify elevator tubes (63 & 56). Attach lower elevator tubes (56) and counter balance spring (68) to backboard support brackets (52) using sp acers (59), bolt (57), and nut (58) as shown.
20 P/N 211574 09/04 22. 52 15 15 70 60 62 68 23. 58 63 63 57 59 52 59 S tarting with nuts (15) flush against bracket (52) secure rim (70) and bracket to backboard. IMPORT ANT! For spring loaded rim assembly , refer to instructions included with rim hardware.
09/04 P/N 211574 21 58 58 65 64 56 1 66 66 57 67 56 67 24. Support pole on sawhorse. Att ach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: T wo people are recommended for this step. Use caution; elevator assembly is heavy .
22 P/N 211574 09/04 26. Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). USE EYE PROTECTION WHEN INST ALLING SPRINGS.
09/04 P/N 211574 23 SECTION D: INST ALL FRONT COVER & HANDLE 27. Attach front cover (40) to hinge tubes (18) using carriage bolt s (51) and flange nuts (22) as shown. 40 61 15 24 Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (42) in place.
24 P/N 211574 09/04 29. Roll assembly to desired playing area. Secure assembly to ground using strap (44) and tie down stake (7). 44 7 8 30. ELEVATOR HEIGHT ADJUSTMENT 35 A. B. C. 31 DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. W ARNING! 31. A. While holding handle, remove pin (35).
09/04 P/N 211574 25 W ARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. AVERTISSEMENT : L'utilisation de ce produit sans installer correctement ou toutes les pinces du filet risque de causer des blessures.
26 P/N 211574 09/04 Install net. Installez le filet. Das Netz anbringen Instale la red. Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se muestra.
Een belangrijk punt na aankoop van elk apparaat Huffy N53 W24700 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Huffy N53 W24700 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Huffy N53 W24700 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Huffy N53 W24700 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Huffy N53 W24700 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Huffy N53 W24700 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Huffy N53 W24700 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Huffy N53 W24700 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
