Gebruiksaanwijzing /service van het product 967C van de fabrikant Humminbird
Ga naar pagina of 143
.
T hank Y ou! Thank y ou for choosing Humminbird®, America's #1 name in fishfinder s. Humminbird® has built its reputation b y designing and man ufacturing top-quality , thoroughly reliable marine equipment. Y our Humminbird® is designed for tr ouble-free use in even the har shest marine environment.
T able of Contents ii 900 Series™ Introduction 1 How the 900 Series™ W orks ............................................................................ 1 3D Sonar ...................................................................................
T able of Contents iii INFO Key .......................................................................................................... 34 MARK Key ....................................................................................................
T able of Contents iv 2D Sonar X -Press™ Menu 63 Active Side ........................................................................................................ 63 Split Position .................................................................
T able of Contents v Delete All Images (optional-purchase MMC/SD Card, Snapshot and Recor ding Vie w only).................... 78 Delete Recording (optional-purchase MMC/SD Card, Snapshot and Recor ding Vie w only).................... 78 Delete All Recordings (optional-purchase MMC/SD Card, Snapshot and Recor ding Vie w only).
T able of Contents vi Course Projection Line .................................................................................... 93 Export All Nav Data (Advanced) ........................................................................ 93 Delete All Nav Data (Advanced) .
T able of Contents vii Time F ormat (Advanced, International only) ...................................................... 109 Date Format (Advanced, International only) ...................................................... 109 Digits Format (Advanced) .
900 Series™ Introduction Y our 900 Series™ Ultra Wide Screen Fishing System comes in the f ollowing configuration: • Humminbird® 967c 3D Combo: Ultra Wide Screen Fishing System with Chartplotter (Maps) and Dual Frequency 455 kHz and 83 kHz T ransducer , GPS Receiver included.
The sound pulses ar e transmitted at various frequencies depending on the application. V ery high frequencies (455 kHz) are used for greatest definition but the operating depth is limited. High frequencies (200 kHz) are commonly used on consumer sonar and provide a good balance betw een depth performance and resolution.
How GPS and Cartogr aphy W ork Y our 900 Series™ Fishing System also supports GPS and chartplotting, and uses GPS and sonar to determine your position, display it on a grid, and provide detailed underw ater information. T he Global P ositioning System (GPS) is a satellite navigation system designed and maintained by the U.
Y our unit also comes with a built-in UniMap™ with a more detailed map of North America (Domestic models) or a more detailed map of Europe and Southeast Asia, including Australia and Ne w Zealand (International models).
Installation Overvie w Please read all instructions that are r elevant for y our configuration befor e beginning the installation process. NO TE: Installation procedures will depend on product configuration. The 900 Series™ has a wide v ariety of configurations.
Inside the boat there is often a channel or conduit used for other wiring, this can be used to route cables. Be sure to r oute the cable as far as practical from the antenna cable of VHF radios or tachometer cables to r educe the possibility of interference.
1. Place the control head into the gimbal brack et. Make sure that the straight side of the gimbal arm is against the back side of the control head. 2. Place a 1" (25 mm) diameter black washer on the gimbal knob and then thread the knob and washer into the housing.
5. Set the gimbal bracket aside and drill the f our mounting screw holes using a 5/32" (4.0 mm) drill bit. 6a. If the cables must pass through a hole directly beneath the mounting bracket, mark and drill an additional 1" (25 mm) hole centered between the f our mounting holes.
9. Insert cable connectors into the proper r ecesses on the cable collector insert. The cable connector s are ke yed to pre vent re verse installation, so be careful not to for ce the connectors into the wrong slots. If you don’t hav e a cable for every hole in the insert, install the blank plugs to protect the control head fr om the weather .
10. While holding cables in place in the cable collector insert, thread the cables through the slot in the bottom of the cable collector cover , line up the cable collector insert and cover , then slide the cover into place on the insert. NO TE: The tab on the Cable Collector insert goes into the slot on the cover .
Connecting the Control Head P ower Cable to the Boat A 6' (2 m) long power cable is included to supply po wer to the control head. Y ou may shorten or lengthen the cable using 18 gauge multi-stranded copper wire. CA UTION: Some boats have 24 or 36 V olt electric systems, but the control head MUST be connected to a 12 VDC power supply .
T ransducer Installation Ther e are three diff erent installation methods for y our transducer: • T ransom T ransducer • Inside the Hull T ransducer • T rolling Motor T ransducer . Find the section that describes the method of installation you will be using.
Determine transducer mounting location NO TE: If transom mounting is not possible because of a stepped hull or cavitation noise, and you hav e a single layer fiber glass hull, In-hull installation is an option. See Inside the Hull T ransducer Installation for mor e information.
2. Hold the template on the transom of the boat in the location wher e the transducer will be installed. Align the template vertically , matching the lower edge of the tr ansom with the bottom corner of the template.
Mount the transducer pivot assembly to the br acket 1. Slide the assembled transducer into the metal brack et from the bottom, aligning the large hole at the top of the brack et with the hole in the pivot. 2. Insert the headed pin through the pivot holes in the br acket and pivot.
4. In order to gain access to the mounting screws, the tr ansducer assembly must be pivoted up in the brack et as shown. Be careful not to alter the running angle as some force is necessary to piv ot the assembly .
3. Place the escutcheon plate over the cable hole and use it as a guide to mark the two escutcheon plate mounting holes. Remove the plate, drill tw o 9/64" (3.6 mm) holes, then fill both holes with marine-grade silicone sealant. Place the escutcheon plate over the cable hole and attach with two #8 x 5/8" (16 mm) wood scr ews.
Determine the transducer mounting location Decide where to install the transducer on the inside of the hull. Consider the following to find the best location: • Observe the outside of the boat hull to find the areas that are mostly free from turbulent w ater .
7. Once you have determined the best mounting location using the above steps, mark the position of the tr ansducer . Route the cable 1. Once the mounting location is determined and you hav e marked the position of the transducer , route the cable from the transducer to the control head.
T rolling Motor T ransducer Installation If you want to install the tr ansducer on a trolling motor , use this procedure. Sever al styles of the transducer are compatible with tr olling motor mounting. If you hav e a trolling motor bracket, refer to the separ ate installation instructions that are included with the brack et.
4. If the unit is working properly , gradually increase the boat speed to test high-speed performance. If the unit functions well at lo w speeds but begins to skip or miss the bottom at higher speeds, the transducer requir es adjustment.
Stem Mounting with an Existing 1" - 14 T hread Stem Follow these steps to stem mount the GPS r eceiver: NO TE: If you have an existing stem f or mounting the GPS receiv er , proceed directly to step 2 of the follo wing procedur e. 1. Determine the best location to mount your GPS receiv er .
Access Under Mounting Location Follow these steps to deck mount the GPS r eceiver when routing the cable down through the mounting location: 1. Determine the best location, then test route the 20' (6 m) cable from the mounting location to the control head.
3. The GPS receiv er has two wire r outing notches. Use the cable notch closest to the intended cable route. 4. With the cable routed, position the GPS r eceiver in the planned mounting location and mark the mounting holes with a pencil or punch. 5. Move the GPS r eceiver to the side and drill the two 9/64" (3.
T emperatur e Probe Accessory Installation The T emperature Probe incorpor ates a temperature sensitiv e probe in a high-impact plastic housing. The module is intended for installation on the transom, and will work w ell on almost any boat.
NO TE: On fiberglass hulls, it is best to start with a smaller drill bit and use pr ogressively larger drill bits to reduce the chance of chipping or flaking the outer coating. 2. All mounting screws not specified r equire a 9/64” (3.5 mm) pilot hole drilled approximately 5/8” (16 mm) deep.
Getting Started - Using Y our 900 Series™ Y our 900 Series™ Fishing System user interface is easy to use. A combination of keys, diff erent views, and situation-specific, customizable menus allows you to contr ol what you see on the color display .
What’s On the 3D Sonar Displa y The 900 Series™ can displa y a variety of useful 3D information about the ar ea under and adjacent to your boat, including the follo wing items: 3D Bottom Contour - Shows the shape of the bottom derived from depth measurements on 6 beams.
What’s On the 2D Sonar Displa y The 900 Series™ can displa y a variety of useful 2D information about the ar ea under and adjacent to your boat, including the follo wing items: Sonar Color Bar - color spectrum indicating low to high sonar intensity returns, where red indicates high intensity and white indicates low intensity .
Real T ime Sonar (RTS®) W indow A Real Time Sonar (R TS®) Windo w appears on the right side of the display in the Sonar V iew only . The RTS® W indow alwa ys updates at the fastest rate possible for depth conditions and shows only the r eturns from the bottom, structure and fish that are within the tr ansducer beam.
W hiteLine® highlights the strongest sonar returns in white, resulting in a distinctive outline. T his has the benefit of clearly defining the bottom on the display .
T o adjust the backlight or to adjust the display background color , press the POWER/LIGHT key to access the Light and Background menu. Use the 4-W AY Cur sor key to select Light or Backgr ound and then use the LEFT or RIGHT Cursor ke y to change the settings.
4-W A Y Cursor Control K ey The 4-W A Y Cursor Control Key has multiple functions, depending on the situation: Fr eeze Fr ame - Pressing any arr ow on the 4-W A Y Cursor Control ke y will freeze the displa y in the Sonar V iew and a cursor and cur sor dialog box will be displayed.
INFO Ke y Press the INFO ke y while in any navigation view to displa y information about objects that are near est to an active cursor . If the cursor is not active, the f ollowing menu will be displayed.
ZOOM (+/-) Ke ys Press the - or + ZOOM k eys while in any of the Na vigation V iews or the Sonar Zoom V iew to change the scale of the view to appear closer or farther aw ay . Vi ew s The vie ws available on y our 900 Series™ are: 3D/2D Combo V iew is the default vie w .
3D/2D Combo V iew 3D/2D Combo V iew displays a 3-dimensional representation of the bottom next to the traditional 2-dimensional sonar repr esentation. The 3D/2D Sonar Combo V iew is especially useful for e valuating the bottom terrain fr om the 3D window while simultaneously viewing the 2D windo w for structure and bottom hardness.
2D Sonar V iew 2D Sonar V iew is a 2-dimensional view that presents a historical log of 2D sonar returns. When in 2D Sonar V iew , your unit operates like a typical depthsounder .
2D Zoom V iew 2D Zoom V iew incr eases the displayed resolution to separ ate sonar returns that are very close together , such as those caused by fish suspended close to the bottom or within structure. In 2D Zoom V iew , the display is split to show the full range vie w on the right and the zoomed view on the left.
6-Beam Sonar V iew 6-Beam Sonar V iew displays information from each of the six 455 kHz beams in a traditional 2D repr esentation. This vie w displays the ra w sonar returns from each of the beams that ar e used to create the 3-dimensional wire frame r epresentation of the bottom in the 3D Sonar V iew .
Snapshot and Recording V iew Snapshot and Recording V iew displays and allows you to view both scr een snapshot thumbnails and recording icons captur ed to an optional-purchase MMC/SD card installed in your unit.
Screen Snapshot: When Scr een Snapshot is enabled (from the Accessories menu tab), pressing the MARK ke y creates a saved scr een capture (when you hav e an optional-purchase MMC/SD card installed).
4. Stopping a recording using the Snapshot and Recor ding X -Press™ menu. 5. Playing back a recor ding, using the Snapshot and Recording V iew and the 4-W ay Cursor k eys, and changing the playback speed using the Snapshot and Recording X -Press™ menu.
Playing back a recor ding: Highlight a recor ding icon (using the Up or Down 4-W ay Cursor k eys), then use the Right 4-W ay Cursor key to start pla yback.
Bird’s Ey e V iew Bird's Eye V iew shows a 3D perspectiv e view of the track and the chart land contour from a point abov e and behind the boat (the eye point). As the boat turns, the eye point mo ves to follow the boat. Big Digits on this view provide digital data in a large, easy-to-see f ormat.
Chart/Bird’s Ey e Combo V iew Chart/Bird’s Eye Combo V iew sho ws both the Chart and Bird’s Eye views in a combination split screen. Y ou can perform any of the functions for either of these vie.
Chart/Chart Combo V iew Chart/Chart Combo V iew shows two ver sions of the Chart view in a combination split screen, so that you can see the position of the boat on one side while you zoom in or perf orm other functions on the other .
Chart V iew Chart V iew shows cartogr aphy from the built -in UniMap™ or an optional MMC/SD map for the area surr ounding your current position. T he current track (also known as the position histor.
Chart/3D Combo V iew Chart/3D Combo V iew shows both the Chart and 3D Sonar views in a combination split screen. Y ou can perform any of the functions for either of these views, but only when the view.
Chart/2D Combo V iew Chart/2D Combo V iew shows both the Chart and 2D Sonar vie ws in a combination split screen. Y ou can perform any of the functions for either of these views, but only when the vie.
Chart Orientation All the chart views allow y ou to choose the orientation of the chart. When North-Up orientation is selected, T rue North is shown at the top of the display . In other words, objects located to the north of the boat are drawn above the boat.
Nearest P ort: The position and services information for the near est port to your present position will be displa yed. Press the EXIT ke y to remov e the information box and the Bullsey e Cursor will be centered ov er the port position. The Cur sor Information Boxes will indicate the distance and bearing to the port from your pr esent position.
W aypoints, Routes and T racks W aypoints are stored positions that allow you to mark ar eas of interest or navigation points. Y our 900 Series™ can store up to 3000 waypoints. Routes link two or more w aypoints together to create a path for na vigation, and are used in trip planning.
Sav e, Edit, or Delete a W aypoint Save y our current position as a w aypoint: On any view , press the MARK key to sa ve the current position of the boat as a wa ypoint. Save the cur sor position as a wa ypoint: On the Chart or Combo view , use the Cursor ke y to designate the position you want to sav e as a waypoint.
Navigate to a W aypoint or P osition Navigate to the cursor position: F rom an y Chart or Combo view , use the Cursor ke y to select a position or waypoint to which y ou want to navigate.
Add or Remove a T rolling Grid: From the W aypoints submenu (accessed from the Navigation main menu), select Grid and press the RIGHT Cur sor key to display a list of waypoints.
Route Info: F rom the Routes submenu, select Info and press the RIGHT Cursor ke y . A list of saved routes will appear . Select the route for which you want information, and pr ess the RIGHT Cursor key .
Man Overboar d (MOB) Navigation As soon as you know that y ou have a man ov erboard, you should activ ate MOB navigation to maximize chances f or a successful rescue. MOB navigation allows y ou create an MOB waypoint to locate the point at which your man went o verboard, and the relation of the boat to that point.
T he Menu System The menu system is divided into easy -to-use menu modules. T he main components of the menu system are: Start-Up Options Menu: Press the MENU k ey during the pow er up sequence to view the Start -Up Options menu. See Start-Up Options Menu .
T otal Screen Update: when you change any menu settings that aff ect the Sonar V iew , the view will update immediately (i.e. you don’t ha ve to exit the menu to apply the change to the screen). Start -Up Options Menu Press the MENU ke y when the Title scr een is displayed to access the Start - Up Options menu.
Normal Operation Use Normal operation for on-the-water operation with a transducer connected. In addition, your 900 Series™ uses advanced tr ansducer detection methods to determine if a transducer is connected.
Self T est Self T est displays results fr om the internal diagnostic self test, including unit serial number , Printed Circuit Board (PCB) serial number , software revision, total hours of operation and the input v oltage. Accessory T est Accessory T est lists the accessories connected to the system.
62 GPS Diagnostic V iew GPS Diagnostic V iew , which is only av ailable when a GPS Receiver is attached to you 900 Series, shows a sk y chart and numerical data from the GPS receiver . The sky chart shows the location of each visible GPS satellite with its satellite number and a signal strength bar .
2D Sonar X-Pr ess™ Menu (2D Sonar Vie ws only) The 2D Sonar X -Press™ Menu provides access to the settings most frequently used. Press the MENU ke y once while in any of the 2D Sonar V iews to access the 2D Sonar X -Press™ Menu.
Split P osition Split P osition allows you to adjust what percentage of the screen is tak en up by the left side of any Combo V iew; each view may be adjusted independently ; you must be in a specific view to adjust the screen size f or that view .
Upper Range 2D Sonar, or 3D/2D Combo V iew when 2D Sonar side is active only) Upper Range sets the shallo west depth range that will be display ed on the 2D Sonar V iew , or 3D/2D Combo V iew when the 2D Sonar side is active.
Chart Speed Chart Speed determines the speed at which the sonar information mov es across the display , and consequently the amount of detail shown. A faster speed sho ws more information in the Sonar V iews and is pref erred by most angler s; howe ver , the sonar information moves acr oss the display quickly .
2D/3D Priority 2D/3D Priority allows you to change the way the 6 beams on the tr ansducer are used in order to prioritize and customize the 2D and 3D display of inf ormation.
3D Sonar X-Pr ess™ Menu (3D Sonar Vie ws only) The 3D Sonar X-Press™ Menu provides access to the settings most frequently used. Press the MENU ke y once while in any of the 3D Sonar V iews to access the 3D Sonar X -Press™ Menu.
6-Beam Sensitivity (6-Beam Sonar Vie w only) 6-Beam Sensitivity contr ols how much detail is shown on the displa y , and is only available when y ou are in the 6-Beam Sonar V iew . Increasing the sensitivity shows more sonar r eturns from small baitfish and suspended debris in the water; the display ma y become too cluttered, howe ver .
T o adjust the 3D Low er Range: 1. Highlight 3D Lower Range on the 3D Sonar X -Press™ Menu. 2. Use the LEFT or RIGHT 4-W A Y Cursor Control keys to incr ease or decrease the Low er Range setting.
T o change the 2D/3D Priority : 1. Highlight 2D/3D Priority on the 3D Sonar X-Press™ menu. 2. Use the LEFT or RIGHT 4-WA Y Cursor Control keys to change the 2D/3D Priority . (2D Only , Equal, 3D, Default = 3D) Cancel Navigation (only when Navigating) Cancel Navigation discards the curr ent route and exits Navigation Mode.
Active Side Active Side allows you to select which side of a Combo V iew will be active; k ey presses will only aff ect the active side of the screen. When a menu is displa yed, the non-active side of the scr een will be gray ed out; at any other time, a green arro w will point to the active side.
T arget allows you to apply a target to a w aypoint selected from the list of waypoints. Grid allows you to apply a tr olling grid to a waypoint selected from the list of waypoints. Cursor to W aypoint (Chart or Combo view only) Cursor to W aypoint allows you to quickly move the cur sor to any saved waypoint, so that y ou can locate it or edit it.
Sav e Current Route (Only when navigating) Save Curr ent Route allows you to save the curr ent route being display ed. This menu choice will only appear when y ou are currently na vigating a route. T o Sa v e Curr ent Route: 1. Highlight Save Current Route on the Navigation X -Press™ Menu.
Remov e T arget (Only if a T arget is active) Remove T arget remo ves the wa ypoint target from the displa y . This menu choice will only appear when a target has already been applied to a waypoint. T o Remove a T ar get: 1. Highlight Remove T arget on the Navigation X -Press™ Menu.
T he W a ypoint Submenu contains the f ollowing menu choices: Edit allows you to edit the Name, P osition (Latitude and Longitude) and select the Icon that will be used to represent the w aypoint in the Chart and Combo V iews. Delete allows you to delete a waypoint from the list of sa ved wa ypoints.
Start Recording (optional-purchase MMC/SD Card, Snapshot and Recording V iew only) Start Recording allows y ou to start sonar recording from the Snapshot and Recording V iew . T his menu option is only available when y ou have an optional-purchase MMC/SD card installed and y ou are in Snapshot and Recording V iew .
Delete All Images (optional-purchase MMC/SD Card, Snapshot and Recording V iew only) Delete All Images allows you to delete all the images at once fr om the Snapshot and Recording V iew . T his menu option is only available when y ou have an optional-pur chase MMC/SD card installed and you are in Snapshot and Recording V iew .
Delete All Recordings (optional-purchase MMC/SD Card, Snapshot and Recording V iew only) Delete All Recordings allows you to delete all the recor dings at once from the Snapshot and Recording V iew . T his menu option is only available when you hav e an optional-purchase MMC/SD card installed and you ar e in Snapshot and Recording view .
Playback Speed (optional-purchase MMC/SD Card, Snapshot and Recording V iew only) Playback Speed allows y ou to specify the playback speed for a sonar recording fr om the Snapshot and Recording V iew . T his menu option is only available when y ou have an optional-purchase MMC/SD car d installed and you are pla ying back a recording.
Sonar Menu T ab Press the MENU ke y twice to access the Main Menu System and then press the RIGHT Cursor ke y to select the Sonar tab. NO TE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode or whether a 2D or a 3D View is displa yed/active.
3D Fr ame Style 3D Fr ame Style selects the frame style used in the 3D Sonar V iew . T o change the 3D F r ame Style setting: 1. Highlight 3D Frame Style on the Sonar main menu. 2. Use the LEFT or RIGHT 4-W A Y Cursor Control keys to change the 3D Frame Style setting.
T o set Fish ID+™: 1. Highlight Fish ID+ on the Sonar main menu. 2. Use the LEFT or RIGHT 4-WA Y Cursor Control keys to change the Fish ID+ setting. (3D Marker s, Symbol Only , Symbol+Depth, Off, Default = 3D Marker s) Fish ID Sensitivity Fish ID Sensitivity adjusts the threshold of the Fish ID+™ detection algorithms.
Real T ime Sonar (RTS®) W indow RTS® W indow sets the RTS® Window to either Wide or Narro w , or turns it off in the Sonar Vie w . The RTS® W indow always updates at the f astest rate possible and only displays returns that ar e within the transducer beam.
83 kHz Sensitivity (Advanced) 83 kHz Sensitivity changes the sensitivity of the 83 kHz beam. Increasing the 83 kHz Sensitivity will display additional weak r eturns and decreasing the 83 kHz Sensitivity will display fe wer weak returns.
Surface Clutter (Advanced) Surface Clutter adjusts the filter that remov es surface clutter noise caused by algae and aeration. T he lower the setting, the less surface clutter will be displayed. T he Surface Clutter menu choice is available when User Mode is set to Advanced (see Setup Menu T ab: User Mode ).
Max Depth (Advanced) Max Depth adjusts the maximum depth of 2D oper ation. The perf ormance of your 900 Series™ can be tuned to the maximum depth you will be fishing in by setting the Max Depth. When a maximum depth is set, y our 900 Series™ will not attempt to acquire sonar data below that depth, thus increasing ov erall performance.
Color Bar Color Bar allo ws you to display or suppr ess the display of the color bar shown in the full scr een Sonar V iew . T o change the display of the Color Bar: 1. Highlight Color Bar on the Sonar Main menu. 2. Use the LEFT or RIGHT 4-WA Y Cursor Control keys to change the display of the color bar .
Current T rack Current T rack allows you to view the Current T rack submenu. T o vie w the Current T r ack Submenu: 1. Highlight Current T rack on the Navigation main menu. 2. Use the RIGHT 4-W A Y Cursor Control keys to vie w the Current T rack submenu.
W aypoints W aypoints allows you to view the W aypoints submenu. T o vie w the W a ypoints Submenu: 1. Highlight Waypoints on the Na vigation main menu.
T he Routes Submenu contains the f ollowing menu choices: Create allows y ou to create a new , empty route and add waypoints to it immediately . Edit allows you to select a previously -saved r oute and edit its name and the waypoints on it. Delete allows you to delete a r oute from a list of previously -sav ed routes.
T rackpoint Interval T rackpoint Interval allows you to select the time period between trackpoints. T he current track can only contain up to 20,000 trackpoints, so longer time periods cause the track to extend back further in time, but will be less detailed.
T rack Color Range T rack Color Range allows you to set the depth range that will be display ed as black, the deepest depth, when Color By Depth is selected as the style for the current tr ack (see Navigation Menu T ab: Current T rack ). NO TE: Only an optional-purchase transducer with a 50 kHz fr equency will allo w you to track to 3,000 feet.
Delete All Nav Data (Advanced) Delete All Nav Data allows you to delete all sav ed T racks, W aypoints and Routes. This menu choice should be used with caution. T o Delete All Navigation Data: 1. Make sure y ou are in Advanced User Mode, then highlight Delete All Nav Data on the Navigation main menu.
Chart Detail Lev el Chart Detail Level allo ws you to select how much chart detail you want displa yed on the Navigation V iews. Basic shows land areas, ports, obstructions and restricted ar eas. Navigation shows navaids, landmarks, f erryways and navigation r outes in addition to the Basic information.
Lat/Lon Grid Lat/Lon Grid allo ws you to display or hide a grid showing latitude and longitude lines. T o change the Lat/Lon Grid setting: 1. Highlight Lat/Lon Grid on the Navigation main menu. 2. Use the LEFT or RIGHT 4-W A Y Cursor Control keys to change the Lat/Lon Grid setting.
Set Simulation P osition (Advanced) Set Simulation P osition allo ws you to set the position of the boat used in the Simulator . T o set the Simulation Position: 1. Activate the cursor and mo ve it to the coordinates fr om where you want simulation to start.
Clear Map Offset (Advanced) Clear Map Offset allo ws you to clear the Map Offset. Clear Map Offset is only accessible if a Map Offset is currently active. T o Clear Map Offset: 1. Make sure y ou are in Advanced User Mode, then highlight Clear Map Offset on the Navigation main menu.
Depth Alarm Depth Alarm sounds when the depth becomes equal to or less than the menu setting. T o change the Depth Alarm setting: 1. Highlight Depth Alarm on the Alarms main menu. 2. Use the LEFT or RIGHT 4-WA Y Cursor Control keys to change the Depth Alarm setting.
Aux T emp Alarm (with optional-purchase temp. probe or T emp/Speed only) Aux T emp Alarm sounds when the w ater temperature fr om the Paddle wheel/T emperature Pr obe detected by the Fishing System r eaches the Aux T emp Alarm setting, which is either set in degrees Fahrenheit or Celsius [International Models only].
Off Course Alarm Off Course Alarm sounds when the boat has moved too f ar off course based on the menu setting when navigating. Off Course Alarm allows y ou to set how far the boat is allow ed to move off course befor e the Off Course Alarm will sound.
Drift Alarm Drift Alarm sounds when the boat has exceeded the distance from the boat’s anchored position, based on the menu setting. Drift Alarm allows you to set the siz e of a perimeter around the boat’s anchored position; if the anchored boat drifts outside of that perimeter , the Drift Alarm will sound.
Setup Menu T ab From an y view , press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor k ey until the Setup tab is selected. NO TE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode and what accessories are attached to the control head.
Units - Distance (with Speed input only) Units - Distance selects the units of measure for all distance-r elated readouts. T o change the Units - Distance setting: 1. Highlight Units - Distance on the Setup menu. 2. Use the LEFT or RIGHT 4-WA Y Cursor Control keys to change the Units - Distance setting.
T riplog Reset (with Speed input only) T riplog Reset r esets the T riplog to zero. T he T riplog provides the following information: timer for elapsed time, distance tr aveled since last reset, and aver age speed. T o Reset T riplog: 1. Highlight Reset T riplog on the Setup menu.
Sonar -only Vie ws, Not Navigating: On Sonar -only views, as long as you are not navigating, all 5 readouts ar e customizable. Other V iews, Not Navigating: On an y view with a chart, as long as you ar e not navigating, two of the r eadouts are not customizable: the 2nd box always displa ys Heading, while the 5th box always displays Speed.
T o Select Readouts: 1. Make sure you ar e in Advanced User Mode, then highlight Select Readouts on the Setup main menu. 2. Use the RIGHT 4-WA Y Cursor Control ke y to initiate this procedure. 3. The Select Readouts submenu will appear , showing a list of all Readouts.
Speed Calibration (Advanced, with Speed paddle wheel only) Speed Calibration will adjust the speed readout b y the percentage entered, and will appear in the menu if a Speed accessory is connected and the paddlewheel has mov ed at least once, when the unit is in Advanced User Mode (see Setup Menu T ab: User Mode .
T ime F ormat (Advanced, International only) T ime Format changes the time format used b y the unit This menu choice is available only when in Adv anced User Mode (see Setup Menu T ab: User Mode .
NMEA Output (Advanced) NMEA Output turns the NMEA output on or off . T his menu choice is available only when in Advanced User Mode (see Setup Menu T ab: User Mode .
V iews Menu T ab From an y view , press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT 4-W AY Cur sor Control ke y until the V iews tab is selected. T his menu tab allows you to set the av ailable views to either hidden or visible in the view rotation.
Accessories Menu T ab From an y view , press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor k ey until the Accessories tab is selected. If no accessories are attached to the Accessory Bus, no accessory menu choices will appear under the Accessories tab, only the Screen Snapshot menu choice.
T o turn Scr een Snapshot on or off: 1. Highlight Screen Snapshot on the Accessories main menu. 2. Use the LEFT or RIGHT 4-W A Y Cursor Control keys to turn Scr een Snapshot On or Off (Off, On, Def ault = Off). T o mak e a screen snapshot (Screen Snapshot must be enabled): 1.
T roubleshooting Before contacting the Humminbir d® Customer Resource Center , please read the following section. T aking the time to review these troubleshooting guidelines may allow y ou to solve a performance problem y ourself , and therefor e avoid sending your unit back f or repair .
Display Pr oblems Ther e are sev eral main conditions or sources of possible interf erence that may cause pr oblems with the quality of the information displayed on the contr ol head. Look in the following table f or some symptoms of display problems and possible solutions: Problem P ossible Cause T he control head loses power at high speeds.
Finding the Cause of Noise Electrical noise usually affects the display with man y black dots at high speeds, and high sensitivity readings. One or more of the follo wing sources can cause noise or in.
1- Y ear Limited W arranty W e warrant the original r etail purchaser that products made b y Humminbird® hav e been manufactured free fr om defects in materials and workmanship. T his warranty is eff ective for one y ear from the date of original retail purchase.
Humminbird® Service P olicy Even though you'll pr obably never need to take adv antage of our incredible service policy , it's good to know that we back our products this confidently .
F or OUT -OF-W ARRANTY service, complete the following steps: • Obtain a Repair Authorization Number from the Humminbir d® Customer Resource Center . • Include payment in the form of cr edit card number and expiration date, money order or per sonal check.
PC Connect Cable: Purchase the PC Connect Cable to connect the 900 Series™ Fishing System to a PC in order to upload pr oduct software updates and new featur es obtained from www .
Specifications 121 Depth Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 ft (75 m) 3D 1000 ft (330m) 2D P ower Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glossary Sonar T erms 122 Alarm, Depth: Depth Alarm is a user -controllable, audible alert that sounds when depth is less than or equal to the setting. Alarm, T emperature: T emperature Alarm is a user -controllable, audible alert that sounds when the water surface temper ature equals the setting.
Glossary Sonar T erms 123 Display , FSTN: FSTN is an acronym for Film Super - T wist Nematic. FSTN is a monochrome display technology char acterized by black, high-contrast pixels. All monochrome fixed mount Humminbird® pr oducts use FSTN technology .
Glossary Sonar T erms 124 display because the user can see the results on the complete sonar gr aph. When combined with the Freez e Frame f eature, the user can adjust and understand the effects of many diff erent sonar settings quickly and easily .
Glossary Sonar T erms 125 QuadraBeam PLUS™: QuadraBeam PLUS™ is a Humminbird® sonar configuration that uses four sonar beams for a mor e detailed bottom image. QuadraBeam PLUS™ uses the DualBeam PLUS™ configuration f or downlooking, and also adds two additional beams to look to the left and right.
Glossary Sonar T erms 126 and structure. Many Humminbir d® units operate at up to 40 times per second when in single frequency operation. Due to the limitation of the speed of sound in w ater , the update rate begins to slow as depth incr eases to deeper than 50 feet.
Glossary Sonar T erms GPS & Navigation T erms 127 T ransducer: The tr ansducer is part of the sonar system, which mounts on the boat and is in contact with the water , that converts the electrical energy from the transmitter into sound energy , and that forms the sonar beam in turn.
Glossary GPS & Navigation T erms 128 Zoom: Zoom is a feature that f ocuses in on a smaller area of the bottom to provide enhanced resolution. With enhanced r esolution, the angler can more easily see fish hanging in structure or multiple fish hanging close together .
Glossary GPS & Navigation T erms 129 Cold Start: Cold Start refer s to the procedure that a GPS receiv er must perform when it does not have historical inf ormation regarding its current location.
Glossary GPS & Navigation T erms 130 This mathematical model is the Map Datum. Historically , many different Map Datums have been used ar ound the world to create maps; often a ref erence to the Map Datum can be found in the legend of a paper map.
Glossary GPS & Navigation T erms 131 Speed Over Ground (SOG): Speed Over Ground is the measurement of the boat’s progress acr oss a given distance, and is the speed measurement pro vided by GPS.
Glossary GPS & Na vigation T erms 132 W aypoint: A W aypoint is the sav ed location (latitude, longitude) of a point of interest that is stored in a GPS r eceiver’s memory . This can include a mark er buoy , dock, fishing hole or anywhere else the user may w ant to return to.
Notes 133.
Notes 134.
Contact Humminbird® Contact the Humminbird® Customer Resource Center in any of the follo wing ways: By T elephone (Monday - Frida y 8:00 a.m. to 4:30 p.m. Central Standard T ime): 1-800-633-1468 By e-mail (typically we respond to y our e-mail within three business days): custserv@johnsonoutdoors.
Een belangrijk punt na aankoop van elk apparaat Humminbird 967C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Humminbird 967C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Humminbird 967C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Humminbird 967C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Humminbird 967C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Humminbird 967C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Humminbird 967C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Humminbird 967C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.