Gebruiksaanwijzing /service van het product 1151435-95 van de fabrikant Husqvarna
Ga naar pagina of 44
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 346XP EP A I 353 EP A III Oper ator’ s manual Please r ead the operator’ s manual car efully and make sur e you understand the instructions before using the machine.
KEY T O SYMBOLS 2 – English Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
KEY T O SYMBOLS English – 3 Y ou will find the follo wing labels on your chain saw: EP A I EP A III The Emissions Compliance P eriod referred to on the Emission Compliance label indicates the number of operating hours f or which the engine has been shown to meet Feder al emissions requirements.
CONTENTS 4 – English Contents KEY T O SYMBOLS Symbols on the machine: 2 Symbols in the operator’ s manual: 2 CONTENTS Contents 4 INTR ODUCTION Dear customer! 5 WHA T IS WHA T? What is what on the .
English – 5 INTR ODUCTION Dear customer! Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , for production of muskets .
6 – English WHA T IS WHA T? What is what on the c hain saw? 1 Cylinder cov er 2 F ront handle 3 Chain brake and front hand guard 4 Star ter 5 Chain oil tank 6 Star ter handle 7 Adjuster screws carb uretor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop switch (Ignition on/off s witch.
GENERAL SAFETY PRECA UTIONS English – 7 Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instr uctions under the heading Assembly . • Refuel and star t the chain saw .
GENERAL SAFETY PRECA UTIONS 8 – English Al wa ys use common sense It is not possible to co ver e very conceivable situation y ou can face when using a chain sa w . Alw ays e xercise care and use your common sense. Avoid all situations which you consider to be be yond your capability .
GENERAL SAFETY PRECA UTIONS English – 9 • The chain brake (A) can either be activ ated manually (by y our left hand) or automatically by the inertia release mechanism.
GENERAL SAFETY PRECA UTIONS 10 – English Will m y hand always activ ate the chain brake during a kickbac k? No . It takes a certain force to mov e the hand guard forw ard. If your hand only lightly touches the front guard or slips ov er it, the force ma y not be enough to trigger the chain brake .
GENERAL SAFETY PRECA UTIONS English – 11 Vibration damping system Y our machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier . The machine ′ s vibration damping system reduces the transf er of vibration between the engine unit/cutting equipment and the machine ′ s handle unit.
GENERAL SAFETY PRECA UTIONS 12 – English • Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance.
GENERAL SAFETY PRECA UTIONS English – 13 Chain • Chain pitch (inches) • Drive link width (mm/inches) • Number of drive links. Sharpening your c hain and adjusting depth gauge setting General inf ormation on sharpening cutting teeth • Nev er use a blunt chain.
GENERAL SAFETY PRECA UTIONS 14 – English • Check that the chain is correctly tensioned. A slack chain will mov e sidewa ys, making it more difficult to sharpen correctly . • Alwa ys file cutting teeth from the inside face . Reduce the pressure on the return stroke.
GENERAL SAFETY PRECA UTIONS English – 15 • Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely b y hand and that it does not sag from the underside of the bar .
GENERAL SAFETY PRECA UTIONS 16 – English Chain drive spr oc ket The clutch drum is fitted with one of the following driv e sprock ets: A Spur sprock et (the chain sprocket is w elded on the drum) B Rim sprock et (replaceable) Regularly check the degree of wear on the drive sproc ket.
ASSEMBL Y English – 17 Fitting the bar and chain Chec k that the chain brak e is in disengaged position by moving the front hand guard tow ards the front handle. Remov e the bar nuts and remov e the clutch cover (chain brake). T ake off the transportation r ing (A).
FUEL HANDLING 18 – English Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be r un using a mixture of gasoline and two-stroke oil. It is impor tant to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.
FUEL HANDLING English – 19 • In temperatures below 32 ° F (0 ° C) some oils become too viscous. This can o verload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling Clean the area around the fuel cap .
ST AR TING AND ST OPPING 20 – English Star ting and stopping Cold engine Starting: The chain br ake should be activated when star ting the chain saw . Activate the chain brake b y pushing the front hand guard forw ards. Ignition; choke: Set the choke control in the chok e position.
ST AR TING AND ST OPPING English – 21 Note! Pull the front hand guard towards the front handle . The chain brake is no w disengaged. Y our saw is ready f or use. • Nev er star t a chain saw unless the bar , chain and all cov ers are fitted correctly .
WORKING TECHNIQUES 22 – English Bef ore use: 1 Check that the chain brak e works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged.
WORKING TECHNIQUES English – 23 5 T ake great care when cutting a tree that is under tension. A tree that is under tension may spring back to its normal position before or after being cut. If you position yourself incorrectly or mak e the cut in the wrong place the tree may hit y ou or the machine and cause you to lose control.
WORKING TECHNIQUES 24 – English 6 Alwa ys use a fast cutting speed, i.e . full throttle. 7 T ake great care when y ou cut with the top edge of the bar , i.e. when cutting from the underside of the object. This is known as cutting with a pushing chain.
WORKING TECHNIQUES English – 25 5 Do the conditions and surrounding terrain aff ect how safely y ou can stand and mov e about? T wo factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is suppor ted before and after cutting, and the second is whether it is in tension.
WORKING TECHNIQUES 26 – English Star t by cutting from abo ve (about 1/3 of the wa y through). Finish by cutting from below so that the tw o cuts meet. T ree felling technique Safe distance The saf e distance betw een a tree that is to be felled and anyone else w orking nearby is at least 2 1/2 tree lengths.
WORKING TECHNIQUES English – 27 Remo v e any undergrowth from the base of the tree and check the area f or obstacles (stones, branches , holes, etc.) so that you ha ve a clear path of retreat when the tree star ts to fall. Y our path of retreat should be roughly 135 degrees aw ay from the intended f elling direction.
WORKING TECHNIQUES 28 – English When the f elling cut and directional cut are complete the tree should star t to fall b y itself or with the aid of a felling wedge or breaking bar . We recommend that y ou use a bar that is longer than the diameter of the tree, so that you can mak e the felling cut and directional cuts with single cutting strokes.
WORKING TECHNIQUES English – 29 Contin ue to cut deeper until tree/limb bends and tension is released. Cut tree/limb from outside the bend, after tension has been released.
MAINTENANCE 30 – English General The user m ust only carry out the maintenance and service work descr ibed in this manual. Carb uretor adjustment Due to e xisting en vironmental and emissions legislation your chain sa w is equipped with movement limiters on the carburetor adjuster scre ws.
MAINTENANCE English – 31 High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity , it ma y be necessary to make minor adjustments to the high speed jet.
MAINTENANCE 32 – English Chec king the inertia brake release With the engine turned off, hold the chain saw o ver a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain sa w rotates around the rear handle.
MAINTENANCE English – 33 Right hand guard Chec k that the right hand guard is not damaged and that there are no visible def ects, such as crac ks. Vibration damping system Regular ly check the vibration damping units f or cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit.
MAINTENANCE 34 – English Starter Changing a broken or w orn starter cord • Loosen the screws that hold the starter against the crankcase and remov e the star ter . • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley .
MAINTENANCE English – 35 Air filter The air fi lter must be regularly cleaned to remov e dust and dir t in order to av oid: • Carburettor malfunctions • Star ting problems • Loss of engine power • Unnecessary wear to engine par ts • Excessive fuel consumption.
MAINTENANCE 36 – English Adjustment of the oil pump The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner .
MAINTENANCE English – 37 F or temper atures below -5 ° C (23 ° F) and/or in snow conditions there is also: • a special cov er (A) for the starter housing • a winter plug (B) for the air nozzle that is fitted as shown. These reduce the flow of cooling air and pre vent large amounts of snow from being suck ed into the carburetor space.
38 – English MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Dail y maintenance Weekl y maintenance Monthly maintenance Clean the outside of the machine .
English – 39 TECHNICAL D A T A T echnical data 346XP 353 Engine Cylinder displacement, cu.in/cm 3 3,06/50,1 3,15/51,7 Cylinder bore, inch/mm 1,74/44,3 1,77/45 Stroke, inch/mm 1,28/32,5 1,28/32,5 Idl.
40 – English TECHNICAL D A T A Recommended original and replacement bar and chain combinations F ollo wing is a list of recommended cutting equipment for the Husqv arna chain saw models 346XP and 353.
English – 41 TECHNICAL D A T A Sa w c hain filing and file gauges.
´®z+Rx=¶5J¨ ´®z+Rx=¶5J¨ 42 – English FEDERAL EMISSION CONTROL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warr anty on your 2009 and later small nonroad engine .
AMERICAN ST AND ARD SAFETY PRECA UTIONS English – 43 Saf ety precautions f or chain saw users (ANSI B 175.1-2000 Annex C) Kickbac k safety precautions With a basic understanding of kickbac k, you can reduce or eliminate the element of surpr ise. Sudden sur prise contributes to accidents.
1151435-95 ´®z+SK[¶5!¨ ´®z+SK[¶5!¨ 2008-12-22.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 1151435-95 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 1151435-95 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 1151435-95 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 1151435-95 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 1151435-95 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 1151435-95 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 1151435-95 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 1151435-95 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
