Gebruiksaanwijzing /service van het product 210 C van de fabrikant Husqvarna
Ga naar pagina of 48
H U S Q VA R N A A U T O M O W E R ™ 2 1 0 C O P E R AT O R ’ S M A N U A L.
TABLE OF CONTENTS English - 3 1. Introduction and safety .............................................................. 5 1.1 Introduction ..................................................................................... 5 1.2 Symbols on Automower™ .
TABLE OF CONTENTS 4 - English Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance and function of products without prior notice. This Operator's Manual deals with version 2.
English - 5 1. INTRODUCTION AND SAFETY 1. Introduction and safety 1.1 Introduction Congratulations on your choice of an exceptionally high quality product.
6 - English 1. INTRODUCTION AND SAFETY 1.2 Symbols on Automower ™ These symbols can be found on the lawn mover. Study them carefully so you understand their significance. • Read through the Operator’s Manual carefully and understand the content before using your Automower.
English - 7 1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully so you understand their significance. • Inspection and/or maintenance must be carried out with the main switch set to OFF .
8 - English 1. INTRODUCTION AND SAFETY 1.4 Safety instructions Use • Please read the Operator's Manual carefully and make sure you understand the instructions before using Automower. • It is not permitted to modify the original design of Automower.
English - 9 1. INTRODUCTION AND SAFETY Transport The original packaging should be used when transporting Automower over long distances. To safely move from or within the working area: 1. Move the main switch to the OFF position if you intend to carry the mower.
10 - English 2. PRESENTATION 2. Presentation This chapter contains information you should be aware of when planning the installation. An installation of Husqvarna Automower™ comprises three main components: Automower, an automatic lawn mower that mows the lawn by moving in an irregular pattern.
English - 11 2. PRESENTATION 2.1 Automower ™ , what’s what? The numbers in the picture correspond to: 1. Cutting height adjustment cover 2. Catch button to open the cutting height adjustment cover 3. Front wheel 4. Drive wheel 5. Body 6. Stop button 7.
12 - English 2. PRESENTATION 2.2 Function of Automower ™ Capacity Automower is recommended for lawns up to 500 m 2 . The size of the working area the mower can handle depends on how much it is used. The larger the lawn the more occasions per week the Automower can work.
English - 13 2. PRESENTATION The blades must be in good condition to obtain the best mowing result. In order to keep the blades sharp for as long as possible it is important to keep the lawn free from branches, small stones and other objects.
14 - English 2. PRESENTATION Working method Automower automatically mows the lawn. Automower automatically mows the lawn. When the battery is discharged the mower stops on the lawn, and you need to carry it to the loop generator/charger for charging. When Automower body hits an obstacle, the mower reverses and selects a new direction.
English - 15 2. PRESENTATION Movement pattern The mower’s movement pattern is irregular and is determined by Automower itself. A movement pattern is never repeated.
16 - English 3. INSTALLATION 3. Installation This chapter describes how you install Husqvarna Automower™. Before starting the installation read the previous chapter 2. Presentation . Read the whole of this chapter too before starting the installation.
English - 17 3. INSTALLATION 3.1 Preparations 1. If the lawn in the proposed working area is taller than 10 cm, mow it using a normal lawn mower. Then collect the clippings.
18 - English 3. INSTALLATION Tip! If, for reasons of space or for some other reason, it is not suitable to charge the mower where the loop generator/charger is positioned, a freestanding charger can also be used. A charger can be purchased as an accessory.
English - 19 3. INSTALLATION 3.4 Installation of the boundary wire The boundary wire can be installed in one of the following ways: • Securing the wire to the ground with staples. It is preferable to staple down the boundary cable, if you want to make adjustments to the boundary wire during the first few weeks of operation.
20 - English 3. INSTALLATION Boundaries for the working area If a high obstacle, for example a wall or fence, borders the working area, the boundary wire should be laid 35 cm from the obstacle. This will prevent Automower from colliding with the obstacle and reduce body wear.
English - 21 3. INSTALLATION Boundaries within the working area Use the boundary wire to demarcate areas inside the working area by creating islands around obstacles that can not withstand a collision, for example, flower beds and fountains. Run the cable out to the area, route it around the area to be demarcated and then back along the same route.
22 - English 3. INSTALLATION Secondary areas It is recommended to create a secondary area when the working area is made up of two areas that are joined by a passage where the distance between the boundary wires is less than 60 cm. Run the boundary wire then around the secondary area so that it forms an island outside of the main area.
English - 23 3. INSTALLATION Automower can mow areas inside the working area that slope up to 35 cm per distance metre (35 %). Areas that slope more must be demarcated by the boundary wire.
24 - English 3. INSTALLATION • Make sure to lay the boundary wire tight to the ground and secure the staples close together with approximately 75 cm between each staple. The wire must generally lie close to the ground so, as not to be cut off before the grass roots have grown over it.
English - 25 3. INSTALLATION Joining the boundary wire If the boundary wire is not long enough and needs to be spliced: Use original solderless coupler. It is waterproof and gives a reliable electrical connection. To splice: Insert both cable ends in the coupler.
26 - English 3. INSTALLATION 3.5 Connecting the boundary wire Connect the boundary wire to the loop generator/charger: 1. Place the cable ends in the connector: • Open the connector. • Place the wire in the connector grip. 2. Press the connector together using a pair of pliers.
English - 27 3. INSTALLATION 3.6 Checking the installation Check the loop signal by looking to see what indication the green LED on the loop generator/charger is giving. • Steady light = the signal is okay. • Flashing once every other second = break in the loop and no signal found.
28 - English 4. USE 4. Use 4.1 Starting Automower™ 1. Press the STOP button to open the control panel cover on Husqvarna Automower™. 2. Set the main switch to the ON position. 3. Enter the PIN code, confirm with the YES button. 4. Close the cover.
English - 29 4. USE 4.3 Restart To start: 1. Enter the PIN code. 2. Press the YES button. 3. Close the control panel cover. 4.4 Switching off Automower™ 1.
30 - English 4. USE 3. Turn the knob to the required position. The selected position is the marking on the knob that aligns with the arrow on the body. • Turn clockwise to raise the cutting height. • Turn anticlockwise to lower the cutting height.
English - 31 4. USE 10. Press the YES button. 11. The yellow indicator lamp PIN code should now be lit with a steady light. 4.7 Sounds The mower indicates the operating status and all input with audio signals as set out below.
32 - English 5. CONTROL PANEL 5. Control panel The control panel on Husqvarna Automower™ consists of in dicator lamps and a keypad. All information is shown throu gh the indicator l amps and all input is done using the buttons. The control panel consists of three groups of bu ttons: select, numbers and main switch, and ind icator lamps.
English - 33 5. CONTROL PANEL 5.3 Main switch 4. Set the main switch in the ON position to start Automower. Set the main switch in the OFF position when you are no t using the mow er or if you want to work on the blade disc. When the main switch is set in the OFF position the motors on the mower cannot start.
34 - English 6. GARDEN EXAMPLE 6. Garden example - Proposed installation An number of installations of Husqvarna Automower™ in different types of gardens are shown and explained in this chapter. See the examples as pointers for how to make the installation in your garden as good as possible.
English - 35 6. GARDEN EXAMPLE Garden with a steep incline (30 %) that divides the garden into two areas, area: 400 m 2 . If the mowing result between the areas is uneven, the garden can ideally be di.
36 - English 7. MAINTENANCE 7. Maintenance Check and clean Husqvarna Automower™ regularly and replace worn parts if necessary to improve operating reliability and to ensure a longer service life. For further information on cleaning, see 7.4 Cleaning on page 39.
English - 37 7. MAINTENANCE 7.2 Winter storage Automower™ Automower must be carefully cleaned before winter storage, see 7.4 Cleaning on page 39. Charge the battery fully before winter storage.
38 - English 7. MAINTENANCE Underframe and blade disc 1. Set the main switch to the OFF position. 2. Wear protective gloves. 3. Lift Automower onto its side. 4. Clean the blade disc and underframe using, e.g. a dish-brush. At the same time, check that the blade disc rotates freely in relation to the motor support, directly above.
English - 39 7. MAINTENANCE Body Use a damp, soft sponge or cloth to clean the body. If the body is very dirty it may be necessary to use a soap solution or washing-up liquid. 7.5 Replacing the blades There are three blades on Automower, which are screwed into the blade disc.
40 - English 7. MAINTENANCE 5. Unscrew the blade. Use a straight slot or cross-tip screwdriver. 6. Pry apart the skid plate and blade disc a little and remove the blade and screw.
English - 41 8. TROUBLE SHOOTING 8. Trouble shooting 8.1 Fault messages A number of fault messages that can be shown by the red Fault indicator lamp on Husqvarna Automower™ are shown below. The fault message is interpreted by reading how the lamp flashes.
42 - English 8. TROUBLE SHOOTING 3 Upside down Automower leans too much or has turned over. Turn the mower the right way up. 3 Trapped Automower has got caught in something.
English - 43 8. TROUBLE SHOOTING 8.2 Fault symptom If your Automower does not work correctly, follow the trouble shooting guide below. If the fault persists; contact your dealer. Symptom Cause Action Uneven mowing results Automower works too few hours per week.
44 - English 9. TECHNICAL DATA 9. Technical data 10. Environmental information The symbol on Husqvarna Automower™ or its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
English - 45 11. EU DECLARATION OF CONFORMITY 11. EU declaration of conformity EU Declaration of Conformity (only applies to Europe) Husqvarna AB , SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, dec.
46 - English 11. EU DECLARATION OF CONFORMITY.
1 2 . INDEX English - 47 1 2 . Index A Automower One in several gardens .......................................15 Technical data .....................................................44 What’s what ....................................................
12. INDEX 48 - English Cleaning .............................................................. 37 Safety Instructions ................................................. 9 Service ................................................................ 37 Underframe .
w w w .automower .com AUTOMO WE R is a t radema rk ow ned by Husqva rna AB . Copy rig ht © 2 00 6 H USQ V A R NA. Al l rig hts re ser ved. 115 03 19 -2 6.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 210 C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 210 C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 210 C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 210 C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 210 C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 210 C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 210 C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 210 C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
