Gebruiksaanwijzing /service van het product 236E van de fabrikant Husqvarna
Ga naar pagina of 23
235e, 236e 240e, 240e T rioBr ak e EN Operator's Manual, 6-23 ES Manual de instrucciones, 24-43 SE Bruksanvisning, 44-61 FI Käyttöohje, 62-79 DK Brugsanvisning, 80-97 NO Bruksanvisning, 98-115 .
2 1153140-26 Rev . 2 2010-02-11 28 27 29 9 14 13 12 11 2 6 4 3 8 10 5 7 24 23 22 21 20 19 18 17 16 15 1 1 30 A A 2 6 10 3 7 4 8 5 9 B E 11 25 26 12 13 11 240e T rioBrake A B C.
3 1153140-26 Rev . 2 2010-02-11 OFF HALF FULL 14 21 27 15 22 28 17 23 29 16 18 24 19 25 20 26 30 31 32 A.
4 1153140-26 Rev . 2 2010-02-11 9 4 3 10 5 7 6, 8 2 33 34 36 38 35 37 40 1 2 1 2 1 3 Retreat path Retreat path Danger zone D anger zone F elling Direct io n Danger zone 39 41 42.
5 1153140-26 Rev . 2 2010-02-11 44 43 A A 1 3 2 45 49 46 50 48 47 51 52 240e T rioBrake.
INTRODUCTION 6 – English 1153140-26 Rev . 2 2010-02-11 Dear Customer , Congratulations on your choice to b uy a Husqvar na product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvar na River , for production of musk ets.
INTRODUCTION / CONTENTS English – 7 1153140-26 Rev . 2 2010-02-11 What is what on the chain sa w? (1) 1 Product and ser ial number plate 2 Throttle lockout (Pre vents accidental operation of throttle control.
GENERAL SAFETY PRECA UTIONS 8 – English 1153140-26 Rev . 2 2010-02-11 Before using a ne w chain saw • Please read this manual carefully . • (1) - (51) refer to figures on p . 2-5. • Check that the cutting equipment is correctly fitted and adjusted.
GENERAL SAFETY PRECA UTIONS English – 9 1153140-26 Rev . 2 2010-02-11 increase your saf ety and efficiency . Visit your dealer regularly to see whether you can benefit from new features that hav e been introduced.
GENERAL SAFETY PRECA UTIONS 10 – English 1153140-26 Rev . 2 2010-02-11 Will m y inertia activated chain brake alwa ys activate during kickbac k in the event of a kic kback? No .
GENERAL SAFETY PRECA UTIONS English – 11 1153140-26 Rev . 2 2010-02-11 General rules • Only use cutting equipment recommended by us! See instructions under the heading T echnical data. • Keep the chain’ s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge.
GENERAL SAFETY PRECA UTIONS 12 – English 1153140-26 Rev . 2 2010-02-11 one side first, then turn the chain saw over and file the teeth on the other side. • File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.
GENERAL SAFETY PRECA UTIONS / ASSEMBL Y English – 13 1153140-26 Rev . 2 2010-02-11 • Check that the bar tip sprock et turns freely and that the lubricating hole in the tip sprocket is not bloc k ed.
FUEL HANDLING 14 – English 1153140-26 Rev . 2 2010-02-11 Fuel Note! The machine is equipped with a tw o-stroke engine and must alwa ys be r un using a mixture of petrol and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.
FUEL HANDLING / ST ARTING AND ST OPPING English – 15 1153140-26 Rev . 2 2010-02-11 T ranspor t and storage • Alwa ys store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/s witches, boilers and the like.
WORKING TECHNIQ UES 16 – English 1153140-26 Rev . 2 2010-02-11 Before use: (33) 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lockout works correctly and is not damaged.
WORKING TECHNIQ UES English – 17 1153140-26 Rev . 2 2010-02-11 8 Unless the user resists this pushing force there is a risk that the chain saw will mov e so f ar backwards that only the kickback z one of the bar is in contact with the tree, which will lead to a kickback.
WORKING TECHNIQ UES 18 – English 1153140-26 Rev . 2 2010-02-11 • Wind direction • Arrangement of branches • Weight of sno w • Obstacles within the reach of the tree: f or example, other trees, power lines , roads and buildings.
W ORKING T ECHNIQUES / MAINTENANCE English – 19 1153140-26 Rev . 2 2010-02-11 If you must cut across tree/limb , make two to three cuts, one inch apar t, one to two inches deep. Continue to cut deeper until tree/limb bends and tension is released. Cut tree/limb from outside the bend, after tension has been released.
MAINTENANCE 20 – English 1153140-26 Rev . 2 2010-02-11 Mov e the front hand guard forwards and back to make sure it mov es freely and that it is securely anchored to the clutch cov er . (47) Checking the inertia brake release Place the chain saw , with the engine switched off, on a stump or other stable surf ace.
English – 21 MAINTENANCE 1153140-26 Rev . 2 2010-02-11 Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine.
TECHNICAL D A T A 22 – English 1153140-26 Rev . 2 2010-02-11 T echnical data Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/EC.
English – 23 TECHNICAL D A T A 1153140-26 Rev . 2 2010-02-11 Bar and chain combinations The follo wing cutting attachments are approved f or the models Husqvarna 235e, 236e, 240e and 240e T rioBrake.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 236E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 236E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 236E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 236E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 236E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 236E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 236E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 236E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
