Gebruiksaanwijzing /service van het product 260 ACX van de fabrikant Husqvarna
Ga naar pagina of 72
H U S Q VA R N A A U T O M O W E R 2 6 0 A C X O P E R AT O R ’ S M A N U A L ®.
TABLE OF CONTENTS English - 1 1. Introduction and safety .................................... 3 1.1 Introduction ....................................................... 3 1.2 Symbols on Automower ® .................................. 4 1.3 Symbols in the Operator’s Manual .
TABLE OF CONTENTS 2 - English Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance and function of products without prior notice. This Operator's Manual deals with version 2.
English - 3 1. INTRODUCTION AND SAFETY 1. Introduction and safety 1.1 Introduction Congratulations on your choice of an exceptionally high quality product.
4 - English 1. INTRODUCTION AND SAFETY 1.2 Symbols on Automower ® These symbols can be found on the lawn mover. Study them carefully so you understand their significance. • Read through the Operator’s Manual carefully and understand the content before using your Automower ® .
English - 5 1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully so you understand their significance. • Inspection and/or maintenance must be carried out with the main switch set to OFF .
6 - English 1. INTRODUCTION AND SAFETY 1.4 Safety instructions Use • Please read the Operator's Manual carefully and make sure you understand the instructions before using Automower ® . • It is not permitted to modify the original design of Automower ® .
English - 7 1. INTRODUCTION AND SAFETY Transport The original packaging should be used when transporting Automower ® over long distances. To safely move from or within the working area: 1. Press the STOP button to stop the mower. If the anti-theft alarm (see page 59) is activated; enter the first digit of the PIN code.
8 - English 2. PRESENTATION 2. Presentation This chapter contains information you should be aware of when planning the installation. An installation of Husqvarna Automower ® includes four main components: Automower ® , an automatic lawn mower that mows the lawn by moving in essentially an irregular pattern.
English - 9 2. PRESENTATION 2.1 Automower ® , what’s what? The numbers in the picture correspond to: 1. Charging strip 2. Cutting height adjustment cover 3. Catch button to open the cutting height adjustment cover 4. Ultrasonic sensors 5. Drive wheel 6.
10 - English 2. PRESENTATION 2.2 Function of Automower ® Capacity Automower ® 260 ACX is recommended for lawns up to 5000 m 2 +/-20%. How large an area is mown depends primarily on the condition of the blades and the type of grass, growth rate and humidity.
English - 11 2. PRESENTATION Working method Automower ® automatically mows the lawn. It continuously combines mowing and charging. The charging station sends out a signal that Automower ® can sense at a distance of 6 - 7 metres. The mower starts to search for the charging station when the battery charge becomes too low.
12 - English 2. PRESENTATION The control panel on the top of Automower ® is where you manage all the mower settings. The main switch is also located on the control panel.
English - 13 2. PRESENTATION 2.3 Search method Automower ® can be set to search for the charging station in three different ways. Using the setting options the three search methods can be combined to optimise the search for the charging station. The required search method or methods depends on the shape of the garden.
14 - English 2. PRESENTATION Search method 3: Follow guide wire Automower ® runs irregularly until it reaches the guide wire. The mower then follows the guide wire in to the charging station.
English - 15 3. INSTALLATION 3. Installation This chapter describes how you install Husqvarna Automower ® . Before starting the installation read the previous chapter 2. Presentation . Read the whole of this chapter too before starting the installation.
16 - English 3. INSTALLATION • Low voltage cable (21) • Nails (24) • Measurement gauge (25) • Connector for the loop wire (23) • Solderless coupler for the loop wire (26) Contact your dealer.
English - 17 3. INSTALLATION Consider the distance to a wall socket when choosing the position. The charging station should be connected to a 230V wall socket via the low voltage cable and transformer. The supplied low voltage cable is 20 metres long.
18 - English 3. INSTALLATION Do not position the charging station so that the mower can come closer than 3 metres behind the charging station (for example on a narrow point). The mower will not then find the charging station. Installation and connecting the charging station 1.
English - 19 3. INSTALLATION 3.3 Charging the battery Automower ® is supplied with an uncharged battery. As soon as the charging station is connected, it is possible to charge the mower. 1. Set the main switch to the OFF position. 2. Place Automower ® in the charging station to charge the battery while you are laying the boundary wire.
20 - English 3. INSTALLATION Best position for the boundary wire The boundary wire should be laid so it: • Forms a loop around the working area for Automower ® . Only an original boundary wire must be used. This is tinned and has a high quality insulation to withstand the dampness in the ground.
English - 21 3. INSTALLATION Boundaries for the working area If a high obstacle, for example a wall or fence, borders the working area, the boundary wire should be laid 40 cm from the obstacle. This will prevent Automower ® from colliding with the obstacle and reduce body wear.
22 - English 3. INSTALLATION When Automower ® searches for the charging station or follows the loop according to the function Follow loop (3-2) (see page 46), it runs along the side of the boundary wire at a specific distance. The Corridor width (3-2-3) function determines the distance from the boundary wire that the mower shall run.
English - 23 3. INSTALLATION Secondary areas It is recommended to create a secondary area when the working area is made up of two areas that are joined by a passage where the distance between the boundary wires is less than 80 cm. Run the boundary wire then around the secondary area so that it forms an island outside of the main area.
24 - English 3. INSTALLATION Slopes The boundary wire can be laid across a slope that slants less than 10 %. The boundary wire should not be laid across a slope that is steeper than 10 %. There is a risk of Automower ® finding it difficult to turn there.
English - 25 3. INSTALLATION Laying out the boundary wire Run the boundary wire around the working area, but wait before connecting the wire to the charging station. Tip! Use the supplied measurement gauge as a guide when you lay out the boundary wire.
26 - English 3. INSTALLATION Laying the boundary wire in towards the charging station The boundary wire can be routed in several different ways in towards the charging station. The best alternative is to route the wire completely outside the charging station, see alternative 1.
English - 27 3. INSTALLATION 3.5 Connecting the boundary wire Connect the boundary wire to the charging station: 1. Lift up the cover on the charging station: • Grip under the edge of the cover with both hands and pull straight out towards the sides.
28 - English 3. INSTALLATION 3. Place the cable ends in the connector: • Open the connector. • Place the wire in the connector grip. 4. Press the connector together using a pair of pliers. Press until you hear a click. 5. Cut off any surplus boundary wire.
English - 29 3. INSTALLATION 7. Refit the cover on the charging station. Ensure the three guides on the charging station enter the right holes in the cover. 3.6 Checking the installation Check the loop signal by looking to see what indication the green LED on the charging station is giving.
30 - English 3. INSTALLATION 3.8 Installation of the guide wire The guide wire is an extra wire that is laid from the charging station, out towards a remote part of the working area or through a narrow passage and is then connected to the boundary wire.
English - 31 3. INSTALLATION • The route to a remote area is long or complicated. When Automower ® shall follow the boundary wire to or from a remote area and the route along the boundary wire to the area is long or complicated. • The boundary wire runs across a long slope (steeper than 10 %).
32 - English 3. INSTALLATION The longer the guide wire, the closer the mower follows the guide wire. If the guide wire is longer then 300 metres, the mower may find it difficult to follow the wire. This varies depending on the design of the garden and installation.
English - 33 3. INSTALLATION If you shall install the guide wire through a passage: • Automower ® follows the guide wire on the same side of the wire both to and from the charging station.
34 - English 4. USE 4. Use 4.1 Charging a discharged battery When Husqvarna Automower ® is new or has been stored for a long period the battery will not be charged and needs to be charged before starting. Charging takes between 1 1/2 and 2 1/2 hours.
English - 35 4. USE 4.2 Using the timer The lawn should not be cut too often to obtain the best mowing result. Use the timer function (see 6.4 Timer (2) on page 43) to avoid a downtrodden lawn and to get the maximum life from your Automower ® .
36 - English 4. USE 4.6 Restart Restart within 20 seconds 1. Close the control panel cover. Automower ® starts automatically. Restart after more than 20 seconds If more than 20 seconds has elapsed since the last time the STOP button or the keypad was pressed it is not possible to start Automower ® by just closing the cover.
English - 37 4. USE 4.8 Adjusting the cutting height The cutting height can be varied from MIN (2 cm) to MAX (6 cm). If the grass is long it is appropriate to let Automower ® start mowing at the MAX cutting height. Once the grass is shorter, you can gradually lower the cutting height.
38 - English 5. CONTROL PANEL 5. Control panel All forms of commands and settings for Husqvarna Automower ® are made via the control panel. All functions are accessed via a number of menus. The control panel consists of a display and a keypad. All information is shown on the display and all input is done using the buttons.
English - 39 5. CONTROL PANEL 5.1 Shortcuts 1. Home: • Sends the mower to the charging station. Where it stays until the button is pressed again. The house icon is lit on the right-hand side of the display when the button is pressed. When the battery is fully charged the mower will remain in the charging station and show the message Waiting .
40 - English 5. CONTROL PANEL 5.2 Select 3. Cancel: • Press to go back one step in the menu structure, or to interrupt an ongoing input. 4. YES: • Press to confirm an entry or selection. • Press to start the mower if more than 20 seconds has elapsed since you last pressed a button and you want to close the control panel cover.
English - 41 6. MENU FUNCTIONS 6. Menu functions 6.1 Main menu The main menu consists of four options: 6.3 Commands (1) 6.4 Timer (2) 6.5 Installation (3) 6.6 Settings (4) The numbers in brackets refer to the menu rows on the display of Husqvarna Automower ® .
42 - English 6. MENU FUNCTIONS 6.2 Automower ® main menu, menu overview Automower ® main menu Normal Test IN Test OUT Commands Timer Installation Settings Security Language Time and date PIN code Ti.
English - 43 6. MENU FUNCTIONS 6.3 Commands (1) This option in the main menu allows you to access the following functions on Automower ® . • Charge then AUTO (1-1) in order for Automower ® to drive immediately to the charging station, charge the battery and then return to the automatic operating mode.
44 - English 6. MENU FUNCTIONS Timer override (2-1) If you set the timer on your Automower ® , you can use this function to temporarily abandon the settings. • YES (2-1-1) Move the cursor to YES and press YES to turn off the timer function. • NO (2-1-2) Move the cursor to NO and press YES to turn on the timer function.
English - 45 6. MENU FUNCTIONS 6.5 Installation (3) From this option in the main menu you access the driving settings. • Exit angles (3-1) to set how far Automower ® should reverse out of the charging station before it turns and in what direction the mower should leave the charging station.
46 - English 6. MENU FUNCTIONS Follow loop (3-2) These functions in this sub-menu are for situations when the mower needs to be guided to reach remote areas, to find the charging station more easily, and to determine at what distance the mower shall follow the loop.
English - 47 6. MENU FUNCTIONS • Direction Specify to the right, left, guide 1 or guide 2 depending on which direction the area lies from the charging station. The direction is set looking from the charging station in the approach direction of the mower.
48 - English 6. MENU FUNCTIONS Automower ® has a default delay setting of 4minutes for guide 1 and guide 2 and 11 minutes for the boundary wire. A delay of 99 minutes means that the function is deactivated.
English - 49 6. MENU FUNCTIONS Different corridor widths can be set for the boundary wire, guide 1 and on guide 2. The default setting on Automower ® is set to a value of 10 for both the boundary wire and guide wires. The higher the stated Corridor width value, the less risk there is of tracks forming.
50 - English 6. MENU FUNCTIONS When the function is selected the mower will immediately follow the boundary wire, guide 1 or guide 2, depending on which one it finds first, in to the charging station. If there is a passage and the mower can not run through it, the Corridor width value is set too high.
English - 51 6. MENU FUNCTIONS Installation shape (3-3) Automower ® can be set according to three garden shapes: Open , Normal and Complex . This setting affects how Automower ® covers a working area when it mows. Above all it influences the turning angles and how often the mower changes direction.
52 - English 6. MENU FUNCTIONS Security (4-1) • PIN code (4-1-1) Via this function you can change your PIN code at any time. • To change the PIN code: Move the cursor to PIN code and press YES . Place Automower ® in the charging station. Enter the new PIN code and press YES .
English - 53 6. MENU FUNCTIONS • Alarm (4-1-3) This function means that the first digit of the PIN code must be entered within 10 seconds after the STOP -button has been pressed or the mower has been lifted up for any reason. If the correct number is not entered after three attempts, the alarm sounds.
54 - English 6. MENU FUNCTIONS • Set the SIM card’s PIN code: Set the marker to SIM PIN and press YES . Enter the SIM card’s four digit PIN code and confirm with YES .
English - 55 6. MENU FUNCTIONS Sounds A number of audio messages are used to indicate what Automower ® is currently doing. Sound Significance 5 beeps over 2 seconds Starting blade disc One long beep .
56 - English 7. GARDEN EXAMPLE 7. Garden example - Proposed installation and settings The behaviour of the mower is controlled by the settings that are made.
English - 57 7. GARDEN EXAMPLE Area: 5000 m 2 . No guide wire is necessary. Timer : Operating time of 24 hours per day. Exit angles : 90° - 270°. Search method: Irregular and Follow boundary wire in. Delay: Guide 1 4 minutes, Guide 2 4 minutes and boundary wire 11 minutes.
58 - English 7. GARDEN EXAMPLE Area: 1600 m 2 . L-shaped garden with the charging station placed in the narrow area. There are two islands. No guide wire is necessary. Timer : Operating time of 8 hours per day. Exit angles : 250° - 290° Search method: Irregular and Follow boundary wire in.
English - 59 7. GARDEN EXAMPLE Area: 3000 m 2 . There are several islands. No guide wire is necessary. The mower’s default settings do not need to be changed. Timer : Operating time of 15 hours per day. Exit angles : 90°- 270°. Search method: Irregular.
60 - English 7. GARDEN EXAMPLE Area: 4500 m 2 . Two guide wires are recommended. Timer : Operating time of 24 hours per day. Exit angles : 90° - 270°. Follow loop out : Area 1; Direction Guide 1, Distance 40 m and Proportion 20 %. Area 2; Direction Guide 2, Distance 30 m and Proportion 40 % .
English - 61 8. MAINTENANCE 8. Maintenance Check and clean Husqvarna Automower ® regularly and replace worn parts if necessary to improve operating reliability and to ensure a longer service life. For further information on cleaning, see 8.5 Cleaning on page 63.
62 - English 8. MAINTENANCE 8.2 Winter storage Automower ® Automower ® must be carefully cleaned before winter storage, see 8.5 Cleaning on page 63. Charge the battery fully before winter storage.
English - 63 8. MAINTENANCE 8.4 After winter storage During a service the dealer can clean the mower thoroughly, test its function and components as well as replace wear parts if necessary. If the charging or contact strips appear to be burnt, clean them using fine grade emery cloth.
64 - English 8. MAINTENANCE Chassis Clean the underside of the chassis. Brush or wipe with a damp cloth. Wheels Clean around the front and rear wheels and around the front wheel suspension. Body Use a damp, soft sponge or cloth to clean the body. If the body is very dirty it may be necessary to use a soap solution or washing-up liquid.
English - 65 8. MAINTENANCE To replace the blades: 1. Set the main switch to the OFF position. 2. Wear protective gloves. 3. Turn Automower ® upside down. 4. Rotate the skid plate so that its hole aligns with the screw for the blade. 5. Unscrew the blade.
66 - English 9. TROUBLE SHOOTING 9. Trouble shooting 9.1 Fault messages A number of fault messages are listed below that can be shown on Husqvarna Automower ® . If the same fault occurs frequently: contact your dealer. Fault message Cause Action Left wheel motor blocked Grass or other object has wrapped around the drive wheel.
English - 67 9. TROUBLE SHOOTING Outside working area If this occurs in isolated areas it may be due to interference from metallic objects (perimeter fence, reinforcement bar) or buried cables in the vicinity. Try moving the boundary wire. The working area slopes too much.
68 - English 9. TROUBLE SHOOTING 9.2 Fault symptom If your Automower ® does not work correctly, follow the trouble shooting guide below. If the fault persists; contact your dealer. Symptom Cause Action Uneven mowing results Automower ® works too few hours per day.
English - 69 10. TECHNICAL DATA 10. Technical data 11. Environmental information The symbol on Husqvarna Automower ® or its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
70 - English 12. EU DECLARATION OF CONFORMITY 12. EU declaration of conformity EU Declaration of Conformity (only applies to Europe) Husqvarna AB , SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, dec.
AUTOMO WER ® is a trad emark o wned by Husqv arna AB . Copyr ight © 2009 H USQVARN A. All rights reserv ed. 115 13 08 -2 6.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 260 ACX (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 260 ACX heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 260 ACX vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 260 ACX leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 260 ACX krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 260 ACX bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 260 ACX kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 260 ACX . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
