Gebruiksaanwijzing /service van het product 323P4, 325P4, 325P5 van de fabrikant Husqvarna
Ga naar pagina of 28
Oper a tor's manual (EP A) Please read these instructions car efully and make sur e you understand them bef ore using the machine. English 323P4 325P4 X-SERIES 325P5 X-SERIES.
2 – English Symbols SYMBOL EXPLANA TION Read through the O perator‘ s Manual carefully and understand the content before using the machine. • Use anti-slip and stable boots.
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal protective equipment .
4 – English The machine‘s saf ety equipment This section describes the machine‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.
English – 5 SAFETY INSTR UCTIONS 3. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible.
6 – English SAFETY INSTR UCTIONS Inspecting, maintaining and servicing machine saf ety equipment IMPORT ANT INFORMA TION • All service and repairs to the machine require special training. • This applies especially to the machine ‘ s saf ety equipment.
English – 7 SAFETY INSTR UCTIONS W ARNING! Never use a machine with defective safety equipment. The safety equipment should be maintained as described in this section. If y our machine does not meet any of these contr ols you should contact your service w orkshop.
8 – English SAFETY INSTR UCTIONS Saw chain • Saw chain pitch (inches) S pacing between drive links. • Drive link width (mm/ inches). • N umber of drive links. Sharpening y our chain and adjusting raker c learance W ARNING! The risk of kic kback is increased with a badly sharpened c hain! A.
English – 9 SAFETY INSTR UCTIONS B. Sharpening cutting tooth T o sharpen cutting teeth you will need a R OUND FILE and a FILE GAUGE. 1. Check that the chain is correctly tensioned. A slack chain is difficult to sharpen correctly . 2. Always file cutting teeth from the inside face, reducing the pr essure on the return stroke.
10 – English SAFETY INSTR UCTIONS D. Adjusting raker clearance • When correction of the raker clearance is made the teeth must be newly sharpened. W e recommend that you adjust the raker clearance every third time you sharpen the chain. NO TE! This recommendation assumes that the length of the cutting teeth is not reduced ex cessively .
English – 11 Chec king wear on cutting equipment A. Saw chain Check the saw chain daily for: • Visible cracks in riv ets and links. • Whether the chain is stiff. • Whether rivets and links are badly worn. Compare the existing chain with a new chain to decide how badly it is worn.
12 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
English – 13 SAFETY INSTR UCTIONS Safety instructions when using the machine ! Protective instructions while working • Always ensure you have a safe and firm working position. • Always use both hands to hold the machine. Hold the machine on the side of the body .
14 – English ! Basic working techniques • The machine should be held as close to the body as possible to get the best balance. • Make sure that the tip does not touch the ground. • Do not rush the work, but work steadily until all the branches have been cut back cleanly .
English – 15 • Use the stop at the base of the bar to provide support during cutting. This will help prevent the cutting equipment from jumping on the branch. • Make an initial cut on the underside of the branch before cutting through the branch from above.
16 – English WHA T IS WHA T? What is what on the mac hine? 1. Lubricant filler hole 2. Bevel gearbox 3. Chain lubrication adjustment screw (B) 4. Chain lubrication locking screw (A) 5. Shaft 6. F ront handle 7. Throttle control 8. Stop switch 9. Throttle lock 10.
English – 17 ASSEMBL Y Fitting the cutting head • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B. NOTE! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head.
18 – English ASSEMBL Y Assembling and dismantling the tw o-part shaft (325P5) Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling ‘ s locking plate on the upper section of the shaft.
English – 19 FUEL HANDLING Fuel mixture ! W ARNING! Alwa ys provide good ventilation when handling fuel. NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensure the correct mixtur e ratio.
20 – English ST ART AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
English – 21 Fine adjustment • When the machine has been ” run-in ” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person.
22 – English Correctly adjusted carburetor A correctly adjusted carburetor means that the machine accelerates without hesitation and the machine 4-cy cles a little at max speed. F urthermore, the cuttingequipment, must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration.
English – 23 MAINTENANCE Cooling system To maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
24 – English MAINTENANCE NO TE: U se only HUSQ V ARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not cov er damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQ V ARNA.
English – 25 TECHNICAL D A T A 323P4 1,50/24,5 1,34/34 1,06/27 12 500 2 700 0,9 kW/ 9 000 rpm Ye s Ye s W albro MB NGK BPMR 7A 0,02/0,5 Zama C1Q 1,06/0,5 0,36/0,17 11,0/5,0 94 107 1,3/1,9 4,0/3,1 T echnical data Engine Displacement, cu. in/cm 3 C ylinder bore, inch/mm S troke length, inch/mm Recommended max.
26 – English TECHNICAL D A T A Type Inch Inch/mm Inch/mm Angle Angle Angle Inch/mm Inch/cm: dl 91VG 3/8" 0,050"/1,3 5/32" /4,0 85° 30° 0° 0,025"/0,65 10"/25:40 12"/3.
English – 27 EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine.
2002W22 ´+H(Q¶5,¨ 114 00 84-95.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 323P4, 325P4, 325P5 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 323P4, 325P4, 325P5 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 323P4, 325P4, 325P5 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 323P4, 325P4, 325P5 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 323P4, 325P4, 325P5 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 323P4, 325P4, 325P5 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 323P4, 325P4, 325P5 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 323P4, 325P4, 325P5 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
