Gebruiksaanwijzing /service van het product 650RTTA van de fabrikant Husqvarna
Ga naar pagina of 28
650R TT A Owner's Manual.
2 • K eep children and pets aw ay . • Do not ov erload the machine capacity by attempting to till too deep at too f ast a rate. • Ne ver oper ate the machine at high speeds on slipper y surf aces. Look behind and use care when backing. • Ne ver allo w bystanders near the unit.
3 CONGRA TULA TIONS on your purchase of a ne w tiller . It has been designed, en gi neered and manu f ac tured to giv e you the best pos sible de penda bil ity and per fo r m ance. Should you e xperience any prob lems y ou can not easily remedy , please contact your nearest authorized ser vice center .
4 T OOLS REQ UIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig.
5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. HANDLE ASSEMBL Y "UP" POSITION FIG. 4 UNP A CKING CAR T ON (See Fig. 2) CA UTION: Be careful of exposed sta ples when handling or disposing of cartoning material.
6 ASSEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA TOR REMO VE TILLER FROM CRA TE • Make sure shift le ver indicator is in “N” position (See Fig. 7) • Tilt tiller forw ard by lifting handle . Separate cardboard cov er from le veling shield.
7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to familiarize y ourself with the location of various controls and adjustments. Sav e this manual f or future ref erence.
8 TURNING • Release the drive control bar . • Mov e throttle control to “SLOW” position. • Place shift lev er indicator in “F” (forw ard) position.
9 OPERA TION OIL LEVEL OIL DRAIN PLUG OIL FILLER PLUG FIG. 12 BEFORE ST ARTING ENGINE IMPORT ANT : BE VER Y CAREFUL NOT TO ALLO W DIR T T O ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND ST ORE IN AP PRO VED , CLEAN, CO VERED CONT AINERS.
10 RUN C H O K E OPERA TION • Soil conditions are impor tant f or proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to e xcessive bounce and diffi cult handling of your tiller . Hard soil should be mois tened before tilling; ho we ver , e xtremely wet soil will “ball-up” or clump dur ing tilling.
11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co ver items that ha ve been subjected to operator ab use or negligence. T o receive full value from the w arranty , the operator must main tain tiller as instructed in this manual.
12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming any maintenance (e xcept car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, lea ves, spilled oil, or fuel.
13 FIG. 18 CO VER KNOB BAS E FO AM PRECLEANER CO VER AIR CLEANER CARTRIDGE COOLING SYSTEM (See Fig. 19) Y our engine is air cooled. F or proper engine perf or mance and long lif e keep y our engine clean. • Clean air screen frequently using a stiff-br istled brush.
14 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire fr om spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited f or your tilling conditions. Handle height will be diff erent when tiller digs into soil.
15 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION T O REPLA CE GR OUND DRIVE BEL T (See Fig. 23) • Remov e belt guard (See “TO REMO VE BEL T GU ARD” in this section of this manual).
16 SER VICE AND ADJUSTMENTS FIG. 26 TINE REPLA CEMENT (See Figs. 24, 25, and 26) CA UTION: Tines are sharp. Wear gloves or other pr otection when han- dling tines.
17 SER VICE AND ADJUSTMENTS FIG. 27 THRO TTLE CONTROL CLAMP SCREW CASING AND WIRE ENGINE T O ADJUST THRO TTLE CONTR OL CABLE (See Fig. 27) The throttle control has been preset at the f actor y and ad just ment should not be necessar y .
18 Immediately prepare your tiller f or storage at the end of the season or if the unit will not be used f or 30 days or more . W ARNING: Ne ver store the tiller with gasoline in the tank inside a build ing where fumes may reac h an open fl ame or spark.
19 Will not start 1. Out of fuel. 1. Fill fuel tank . 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. W ait sev eral minutes bef ore attempting to star t. 4. Dir ty air cleaner . 4. Clean or replace air cleaner car tridge.
20 REP AIR P AR TS TILLER - - MODEL NUMBER 650R TT A, PR ODUCT NUMBER 954 32 91-72 HANDLE ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 17 532 10 92-29 Lock, Handle 18 873 68 06-00 Nut, Crownlock 3/8-16 Unc 19 819 13 16-11 Washer 13/32 x 1 x 11 Ga.
21 KEY P ART NO . NO . DESCRIPTION 1 873 51 05-00 Nut, Keps 5/16-18 2 810 04 06-00 Washer , Lock 3/8 3 873 22 06-00 Nut, Hex 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard RT 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Lev er , Shift 7 872 11 04-04 Bolt, Carr iage 1/4-20 x 1/2 Gr .
22 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P AR TS TILLER - - MODEL NUMBER 650R TT A, PR ODUCT NUMBER 954 32 91-72 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Locknut, He x, Flange 5/16-18 5 532 10 23-32 Brack et, Reinforcement 7 532 10 21-73 Counter W eight, R.
23 KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .S. inches . 1 inch = 25.4 mm 1 532 18 06-77 T ransmission Assembly (In cludes K ey Nos . 2-53) 2 532 18 06-27 Gearcase, L.H. w/Bearing (In cludes Key N o. 4 ) 3 532 16 19-63 Gasket, Gearcase 4 532 00 50-20 Bear ing, Needle 5 532 00 13-70 Washer , Thrust 5/8 x 1.
24 19 532 10 27--01 Grip 20 873 22 06-00 Nut, Hex 3/8-16 21 532 10 21-56 Stake, Depth 22 874 93 06-32 Bolt, Hex 3/8-16 x 2 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carr iage 1/4-20 x 1/2 Gr .
25 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 00 44-59 Tine, Outer , L.H. 2 532 13 26-73 Clevis Pin 3 532 00 65-54 Tine, Inner , L.
26 1 532 18 59-11 Decal, Blt Grd 2 532 18 59-10 Decal, CNTRL PNL 3 532 13 72-82 Decal, Control Tine 5 532 11 06-14 Decal, Hand Placement 6 532 10 21-80 Decal, Shift Indicator 7 532 16 23-84 Decal, W ar ning 8 532 17 10-79 Decal, Engine B&S 6.
27 SECTION 1: LIMITED W ARRANTY Husqv arna Forest & Garden Company (“Husqv ar na”) warrants Husqv arna product to the or iginal pur- chaser to be free from defects in material and workmanship .
532 18 57-98 Re v . 3 05.13.03 TR Printed in U.S .A..
Een belangrijk punt na aankoop van elk apparaat Husqvarna 650RTTA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 650RTTA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 650RTTA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 650RTTA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 650RTTA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 650RTTA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 650RTTA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 650RTTA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
