Gebruiksaanwijzing /service van het product CTH151 van de fabrikant Husqvarna
Ga naar pagina of 48
CTH151 02595 Owner's Manual.
2 SAFETY R ULES Safe Operation Practices f or Ride-On Mower s IMPORT ANT : THIS CUTTING MA CHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THR OW ING OBJECTS. F AILURE T O OBSER VE THE FOLLOWING SAFETY INSTR UCTIONS COULD RESUL T IN SERIOUS INJUR Y OR DEA TH.
3 • Be sure the area is clear of other people before mowing. Stop machine if any one enters the area. • Never carry passengers or children ev en with the blades off . • Do not mow in rev erse unless absolutely necessar y . Al ways look down and behind bef ore and while backing.
4 PR ODUCT SPECIFICA TIONS Gasoline Capacity 2.0 Gallons and type: Unleaded Regular Oil T ype (API-SF-SJ): SAE 10W30 (abov e 32°F) SAE 5W -30 (below 32°F) Oil Capacity: 3.0 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): F orward: 0-5.
5 UNASSEMBLED P AR TS Steering Wheel Steering Wheel Insert (1) Large Flat Washer Steering Boot Steering Extension Shaft Steering Wheel Adapter (1) Bolt (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Ke.
6 02601 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Stan dard wrench sizes are listed. (2) 7/16" wrenches Utility knife (1) 3/4" wrenches Tire p.
7 FIG. 2 025 91 DISCARD TERMINAL PRO TECTIVE CAPS BA TTER Y CO VER KEPS NUT HEX BOL T POSITIVE CABLE (RED) NEGA TIVE CABLE (BLA CK) ASSEMBL Y INST ALL SEA T (See Fig. 3) Adjust seat bef ore tightening adjustment knob. • Remov e adjustment knob and fl at w asher securing seat to cardboard packing and set aside f or assembly of seat to tractor .
8 ASSEMBL Y FIG. 4A FIG. 4B T O INST ALL BA GGER COM PO NENTS T O TRA C T OR (See Figs. 4A-4D) • Remove discharge chute from rear of tractor . Unhook the two (2) straps and pull chute out and a wa y from tractor . • Remov e the two (2) 3/8 nuts and fl at washers from the bolts at the tractor bac k plate.
9 ASSEMBL Y 02329 02593 CLEVIS PIN RE TA I N ER SPRING 1/4 X 2" CARRIA GE BOL TS DUMP HANDLE TUBE 6MM (1/4") - 9MM (3/8") T OP SURF ACES EVEN HOR I ZON TA L AD JUST MENT BRA CKET VERTICAL AD JUST MENT BRA CK ET FIG. 7 VINYL BINDING 1/4 LOCK NUT FRONT B A GGER TUBE FIG.
10 ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRAC- T OR, WE WISH T O ASSURE THA T Y OU RECEIVE THE BEST PERFORMANCE AND SA TISF ACTION FR OM THIS QU ALITY PRODUCT . PLEASE REVIEW THE FOLLOWING CHECKLIST : ✓ All assembly instructions hav e been completed.
11 OPERA TION These symbols ma y appear on your tractor or in literature supplied with the product. Lear n and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models.
12 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments. Sav e this manual f or future reference .
13 OPERA TION 00155 The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age. Al ways wear safety glass es or ey e shields while operating your trac- tor or per form ing any adjustments or repair s.
14 OPERA TION T O OPERA TE ON HILLS W ARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across an y slope. • Choose the slowest speed bef ore star ting up or down hills. • A void stopping or changing speed on hills .
15 T O WING CARTS AND O THER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifi cations of the manuf acturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous .
16 00272 FIG. 14 MULCHING MO WING TIPS IMPORT ANT : FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUIL T -UP GRASS AND TRASH. CLEAN AFTER EA CH USE. • The spe cial mulch ing b lade will recut the grass clip- pings many times and reduce them in size so that as they f all onto the lawn they will disperse into the gr ass and not be noticed.
17 • Cer tain types of grass and gr ass con di tions may re quire that an area be mulched a second time to com pletely hide the clippings. When doing a sec ond cut, mow across or per pendicular to the fi rst cut path. • Change your cutting patter n from w eek to week.
18 MAINTENANCE BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartri.
19 02223 MAINTENANCE TRA CT OR Al wa ys ob ser v e safe ty rules when per fo r m ing any main- te nance. BRAKE OPERA TION If trac tor re quires more than six (6) feet stop ping dis tance at high speed in high est gear , then brake must be ad just ed. (See “TO ADJUST BRAKE” in the Ser vice and Ad just ments section of this manual).
20 V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able . Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
21 MAINTENANCE CLEAN AIR SCREEN Air screen must be k ept free of dir t and chaff to prev ent engine dam age from ov erheating. Clean with a wire br ush or compressed air to re mov e dir t and stubborn dr ied gum fi bers. See engine manual. AIR FIL TER Y our engine will not r un properly using a dir ty air fi lter .
22 02375 W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUSMENTS: • Depress clutc h/brake pedal fully and set parking brake. • Place motion contr ol lever in neutral (N) position. • Place attachment c lutch in “DISENGA GED” position.
23 01156 T O REPLACE MO WER BLADE DRIVE BEL T (See Fig. 29) P ark the tractor on lev el surf ace. Engage parking brake. BEL T REMO V AL - • Remov e mower from tractor (See “TO REMO VE MO W ER” in this section of this man ual). • Remov e screws from RH mandrel co ver and remov e cov er .
24 02232_Hydro SER VICE AND ADJUSTMENTS FIG. 30 FIG. 31 WITH P ARKING BRAKE “ENGA GED” JAM NUT DO NO T T OUCH THIS NUT . IF FUR THER BRAKE AD JUST MENT IS NECESSAR Y CONT A CT Y OUR NEAREST A UTHORIZED SER- VICE CENTER/DEP ARTMENT OPERA TING ARM NUT “A” 1-11/16" 02239 ADJUSTMENT BOL T FIG.
25 T O ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not hor iz ontal (left to r ight) when wheels are positioned straight f orward, remov e steer- ing wheel and reassemble per instructions in the Assembly section of this manual. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tr actor .
26 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
27 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se veral min utes before attempting to start. 4. Bad spar k plug.
28 TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections . If not when operator leaves seat corrected, contact an authorized ser vice center/ with attachment clutc h depar tment.
29 TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 SCHEMA TIC BATTERY STARTER 12VDC STARTER M A AMMETER (OPTIONAL) FUSE REGULATOR HEADLIGHTS CARBURETOR SOLENOID FUEL LINE ALTERNATOR IGNITION UNIT SPARK PLUGS GAP (2 PLUGS ON TWIN CYL.
30 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 ELECTRICAL 33 30 28 29 26 24 42 43 25 41 27 27 27 27 40 48 16 58 59 2 1 27 66 81 22 21 66 16 52 16.
31 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 ELECTRICAL 1 532 14 49-27 Batter y 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 16 532 17 61-38 Switch Inter loc k 21 532 17 56-88 Har ness Asm Light W/4152J 22 532 00 41-52 Bulb Light #1156 24 532 12 47-80 Cable Star ter 6 Ga.
32 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 CHASSIS AND ENCLOSURES 162 164 209 3 26 24 163 209 209 24 2 209 207 35 209 26 209 35 26 175 185 33 10 209 17.
33 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 CHASSIS AND ENCLOSURES 1 532 17 46-20 Chassis 2 532 18 03-84 Drawbar 3 817 06 06-12 Screw 3/8-16 x 3/4 5 532 15 52-72 Bumper Hood/Dash 6 532 18 44-19 Saddle 8 532 12 64-71 Clip Insulator 13/32 Mtg.
34 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 DRIVE 77 77 74 78 75 76 15 1 180 38 42 40 42 39 56 66 51 184 253 26 254 178 179 179 177 120 27 51 48 50 49 4.
35 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 DRIVE 1 - - - - - - - T ransaxle Hydro Gear 321-0510 (Order par ts from transaxle manu facturer) 8 532 16 56.
36 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 STEERING ASSEMBL Y 5 5 4 3 43 95 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 44 51 54 33 35 34 68 67 67 67 13 65 68 15 15 15 29 29 82 steering_pl.
37 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 STEERING ASSEMBL Y 1 532 16 66-27 Steer ing Wheel 2 532 18 47-06 F ront Axle Assembly 3 532 16 98-40 Spindle Assembly , L.H. 4 532 16 98-39 Spindle Assembly , R.
38 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 SEA T ASSEMBL Y 1 24 16 15 12 13 17 25 11 10 5 14 4 3 8 9 7 8 9 7 2 6 22 21 5 seat_lt.knob_7(CRD) 1 532 18 49-92 Seat 2 532 14 05-51 Brack et Pnt Pivot Seat (b lk ) 3 871 11 06-16 Bolt Fin Hex 3/8-16 x 1 4 819 13 16-10 W asher Flat 13/32 x 1 x 10 Ga.
39 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 DECALS WHEELS & TIRES KEY P ART NO . NO. DESCRIPTION 1 532 14 54-98 Decal Read Owner’ s Manual Sym 3 5.
40 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 23 45 44 46 32 31 33 37 33 engine-kohler_42 116 117 4 8 13 1.
41 1 532 17 08-05 Control Throt/Ck 2 817 72 04-08 Screw He x Thd Cut 1/4-20 x 1/2 3 - - - - - - - - Engine K ohler Model SV470 (Order par ts from engine manufacturer) 4 532 18 86-55 Muffl er 8 532 17.
42 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 MO WER LIFT 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 49 26 50 lift-rh.
43 KEY P ART NO . NO. DESCRIPTION 1 532 15 94-60 W asher Asm Inner Spr ing W/Plunger 2 532 15 94-71 Shaft Asm. Lift 3 532 10 57-67 Pin Groov e 4 812 00 00-02 E Ring #5133-62 5 819 21 16-21 W asher 21/32 x 1 x 21 Ga. 6 532 12 01-83 Bear ing Nylong 7 532 12 56-31 Gr ip Handle Fluted 8 532 12 45-26 Button Plunger Black 11 532 16 58-29 Link Asm Lift L.
44 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 MO WER 124 131 36 22 13 2 11 8 20 16 69 14 15 2 18 46 46 45 9 41 130 1 19 5 6 3 46 44 33 32 30 30 28 31 21 25 21 31 32 33 30 30 30 2 18 17 27 55 124 40 41 36 26 23 124 36 84 41 40 56 61 24 21 21 21 4 21 10 68 32 36 36 32 36 36(92cm)_deck-elect.
45 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 MO WER KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532 16 55-52 Housing Asm. Mower 2 872 14 05-06 Bolt Rdhd Sqnk 5/16-18 unc x 3/4 3 532 16 55-69 Brack et Asm.
46 REP AIR P AR TS TRA CT OR- -MODEL NO . CTH151 (HA UCT15HK36A), PRODUCT NO . 954 17 02-29 B A GGER KEY P ART NO . NO. DESCRIPTION NO TE: All component dimensions given in U .S. inches 1 inch = 25.4 mm 1 532 16 52-49 T ube Handle Bagger CRD 2 872 14 04-16 Bolt Carr iage 1/4-20 x 2.
47 SE C TI ON 1: LIMITED W A R R A N TY Husqvar na Forest & Garden Compan y (“Husqv ar na”) w arrants Husqvarna product to the original pur- chaser to be free from defects in material and work.
15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Een belangrijk punt na aankoop van elk apparaat Husqvarna CTH151 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna CTH151 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna CTH151 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna CTH151 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna CTH151 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna CTH151 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna CTH151 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna CTH151 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
