Gebruiksaanwijzing /service van het product GTH2654T van de fabrikant Husqvarna
Ga naar pagina of 44
03002 GTH2654T Owner's Manual.
2 I. GENERAL OPERA TION • Read, understand, and f ollow all instructions on the machine and in the manual bef ore star ting. • Do not put hands or f eet near rotating par ts or under the machine.
3 • Be sure the area is clear of bystanders bef ore operat- ing. Stop machine if anyone enters the area. • Nev er carr y passengers. • Do not mow in re verse unless absolutely necessary . Al wa ys look down and behind bef ore and while back- ing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUST OMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ...................................
5 UNASSEMBLED P AR TS (2) Keys Slope Sheet Keys Mower (1) Wheel (5) Large Retainer Springs - 7/16 (2) Smaller Retainer Springs - 5/16 (1) Locknut 3/8-16 (1) Oil Drain Tube For Future Use (1) Shoulder Bolt Mower Front Wheel (1) Anti-Sway Bar (1) 3/4 O.
6 ASSEMBL Y FIG. 1 02931 CHECK B A TTER Y (See Fig. 1) • Lift hood to raised position. NO TE: If this batter y is put into ser vice after month and year indicated on label (L) (label is located between terminals) charge batter y f or minimum of one hour at 6-10 amps.
7 ASSEMBL Y INST ALL MO WER AND DRIVE BEL T (See Figs. 4-12) See MO WER AND DRIVE BEL T ASSEMBL Y Supplement Sheet f or additional guidance on this assembly . Be sure tractor is on le vel surf ace and engage park ing brak e. • Lower attachment lift le ver to it's lo west position.
8 ASSEMBL Y • A TT A CH REAR LIFT LINKS (C) - Inser t rod end of lift link assembly into hole in tr actor lift shaft suspension arm (L) and pivot link down to mo wer . Lift rear cor ner of mow er and position slot in link assembly ov er pin on rear mower br ack et (D) and secure with washer and retainer spring.
9 ASSEMBL Y CHECK TIRE PRESSURE The tires on your tr actor were ov er infl ated at the f actor y f or shipping pur poses. Correct tire pressure is impor tant f or best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS F or best cutting results, mower housing should be properly le veled.
10 OPERA TION These symbols ma y appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models .
11 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments. Sav e this manual f or future reference .
12 OPERA TION FIG. 14 T O USE CHOKE CONTROL -D (See Fig. 16) Use choke control whene ver y ou are star ting a cold engine. Do not use to star t a warm engine.
13 OPERA TION T O ADJUST MO WER CUT TING HEIGHT (See Fig. 18) The po si tion of the at tach ment lift le v er (A) de ter mines the cut ting height. • Put attachment lift lev er in desired cutting height slot. The cutting height range is ap pro x i mate ly 1" to 4".
14 OPERA TION FIG. 21 T O WING CARTS AND O THER A T TA C H MENTS T ow only the attachments that are recommended by and comply with specifi cations of the manufacturer of y our trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous .
15 ADD GASOLINE • Fill fuel tank to bottom of fi ller nec k. Do not overfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead o xide deposits and reduce valv e life).
16 FIG. 22 MO WING TIPS • Mower should be properly le veled f or best mowing per- f or mance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mower should be used f or trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
17 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
18 MAINTENANCE FIG. 23 02544 MANDREL ASSEMBL Y BLADE BLADE BOL T (SPECIAL) CENTER HOLE ST AR B A TTER Y Y our tractor has a battery charging system which is suf fi cient f or nor mal use. Howe v er , per iodic charging of the batter y with an automotive charger will e xtend its life.
19 MAINTENANCE V -BEL TS Check V -belts f or deter ioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able . Re place belts if they begin to slip from w ear . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
20 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e ver y 100 hours of operation, whiche ver occurs fi rst.
21 SER VICE AND ADJUSTMENTS FIG. 27 W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment c lutch in “DISENGA GED” position. • T urn ignition key to “ST OP” and remove ke y .
22 SER VICE AND ADJUSTMENTS 02966 A A 02548 B B • Go to side of mower y ou wish to adjust. • With a 3/4" or adjustable wrench, tur n lift link adjust- ment nut (A) to the left to low er the mower , or , to the right to raise the mower . FRONT -TO-BA CK ADJUSTMENT (See Figs.
23 SER VICE AND ADJUSTMENTS T O REPLA CE MO WER BLADE DRIVE BEL T MO WER DRIVE BEL T REMO V AL (See Fig. 32) • Park tractor on a le v el surface. En gage par king brak e. • Lower attachment lift le ver to its lo west position. • Disengage belt tension rod (K) from lock brac ket (L).
24 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 34) • Block up axle securely . • Remove axle co ver , retaining r ing and washers to allo w wheel remov al (rear wheel contains a square ke y - Do not lose). • Repair tire and reassemble.
25 SER VICE AND ADJUSTMENTS REPLA CING B A TTER Y (See Fig. 36) W ARNING: Do not shor t batter y ter mi nals by allowing a wrench or any other object to contact both terminals at the same time. Bef ore connecting batter y , remo ve metal bracelets, wristwatch bands , r ings, etc.
26 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gasoline in the tank inside a building where fumes may reac h an open fl ame or spark.
27 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. W ait sev eral minutes bef ore attempting to star t. 4. Bad spark plug.
28 TR OUBLESHOO TING POINTS Engine dies when 1. Re verse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into rever se mower or other attachment See Operation section. is engaged.
29 M FUSE ST ARTER SOLENOID BA TTER Y ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOUR METE.
30 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 ELECTRICAL 30 33 24 42 40 26 28 71 59 194276D 29 34 43 25 27 41 50 Battery _28 8 1 99 100 91 2 27 22 21 16 55 46 46 90.
31 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 14 49-27 Batter y 2 874 76 04-12 Bolt He x Hd 1/4-20 unc x 3/4 8 532 18 64-.
32 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 CHASSIS 14 214 130 130 37 194 194 194 194 181 181 182 68 68 216 216 216 176 176 176 175 178 165 183 184 99 152 150 202 203 2.
33 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 CHASSIS KEY P ART NO . NO . DESCRIPTION 5 532 40 18-23 Dash 14 532 40 18-24 Hood 15 532 19 89-07 Lens LH 18 532 40 02-97 Gri.
34 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 DRIVE 80 56 70 74 220 74 213 171 197 196 206 26 207 209 218 216 219 143 186 189 49 187 50 51 190 52 51 51 52 208 210 170 211.
35 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - T ransaxle , Hydro 344-0610 (Order Parts from T ransaxle Manu- f acturer) 2 532 18 62-11 K ey 1/4 x 2.
36 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_4-husq KEY P ART NO .
37 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 ENGINE KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv en in U .
38 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 SEA T ASSEMBL Y 1 532 19 75-26 Seat 2 532 18 01-66 Brac ket Piv ot Fender 3 532 14 06-75 Strap , Asm F ender 5 532 14 50-06 Clip , Push In, Hinged 6 873 80 06-00 Nut, Lock W/Ins.
39 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 DECALS NO TE: All component dimensions given in U .S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 12 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO .
40 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 MO WER DECK 47 7 49 46 32 33 31 30 1 33 52 52 43 196 97 33 192 49 34 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 58 60 59.
41 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 MO WER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .
42 TRA CT OR - MODEL NO . GTH2654T (96043001000), PRODUCT NO . 960 43 00-10 MO WER LIFT 7 3 87 10 88 2 89 90 87 98 100 99 41 97 97 91 95 41 92 lift-tex_1 2 532 19 52-23 Shaft Asm.
43 15 DEGREES MAX. FO LD ALO NG DO TTED LINE THIS IS A 15 DEG REE SLO PE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the .
Een belangrijk punt na aankoop van elk apparaat Husqvarna GTH2654T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna GTH2654T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna GTH2654T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna GTH2654T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna GTH2654T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna GTH2654T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna GTH2654T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna GTH2654T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
