Gebruiksaanwijzing /service van het product YTH24V54 van de fabrikant Husqvarna
Ga naar pagina of 56
Owner's Manual 532 43 65-47 917.289640 (YTH24V54).
2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AILURE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Keys Mower (1) Wheel (5) Large Retainer Springs - 7/16 (2) Smaller Retainer Springs - 5/16 (1) Locknut 3/8-16 (1) Oil Drain Tube For Future Use (1) Shoulder Bolt Mower Front Wheel (1) 3/4 O.D. Washers (1) Anti-Sway Bar (1) Front Link Assembly (1) 1-1/4 O.
6 AS SEMBL Y NOTE: Y ou may now roll your tractor off the skid. Follow the ap pro pri ate instruction below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al.
7 AS SEMBL Y TRANSAXLE 02965 FRONT BACK ENGINE Q. DEFLECTOR SHIELD Q Fig. 6 90° END INTEGRA TED WASHER END ANTI-SWA Y BAR (S) TOWARDS TOW ARDS TRANSAXLE MOWER DECK • F rom right side of mower , first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle.
8 AS SEMBL Y 6. A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 12) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor .
9 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models o.
11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
12 OPERA TION Fig. 17 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs.
13 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 21) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
14 TO STOP MOWER BL ADES Disengage at tach ment clutch con trol. CAUTION: Do not operate the mower without either the en tire grass catcher , on mowers so equipped, or the deflector shield (S) in place.
15 SERVICE REMINDER/HOUR METER Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. T o service engine and mower , see the Maintenance section of this manual.
16 Fig. 25 MOWING TIPS • Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
17 MAINTENANCE 02956 ➀ General Purpose Grease ➁ Refer to Maintenance “ENGINE” Section ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ MANDREL ZERKS ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➀ STEERING SECTOR GEAR TEETH T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures .
18 MAINTENANCE Fig. 26 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life.
19 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
20 MAINTENANCE CL AMP FUEL FIL TER CL AMP Fig. 29 Fig. 30 • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out.
21 SERVICE AND ADJUSTMENTS Fig. 32 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key .
22 SERVICE AND ADJUSTMENTS FRONT - TO-BACK ADJUSTMENT (See Figs. 36 & 37) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 SERVICE AND ADJUSTMENTS TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced.
24 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 40) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries.
25 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
28 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
30 TRACTOR - MODEL NO . YTH24V54 (289640) ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V Outlet Option 59 103 16 42 T11S 102.
31 TRACTOR - MODEL NO . YTH24V54 (289640) ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Battery Box 16 532 17 61-38 Switc.
32 TRACTOR - MODEL NO . YTH24V54 (289640) CHASSIS 182 68 68 176 195 176 176 175 183 236 150 34 130 130 177 52 189 189 152 217 235 161 14 214 130 130 202 203 204 210 208 18 15 25 239 238 3 207 211 209 .
33 TRACTOR - MODEL NO . YTH24V54 (289640) CHASSIS 3 532 40 50-12 Logo 5 532 40 87-00 Dash Asm 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille 25 532 19 89-06 Lens RH 34 532 19 61-2.
34 TRACTOR - MODEL NO . YTH24V54 (289640) DRIVE 231 51 170 225 125 drive-tex_K46_pedal_39_r1 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 64 188 161 35 184 167 160 42 29 15 159 159 221 186 189 49.
35 TRACTOR - MODEL NO . YTH24V54 (289640) DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - T ransaxle, TUFF TORQ K46BT 2 532 12 35-83 Key 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
36 TRACTOR - MODEL NO . YTH24V54 (289640) ENGINE 30 !2+ª !22%34%2ª+)4 .
37 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 1 - - - - - - Engine Briggs Model No.
38 TRACTOR - MODEL NO . YTH24V54 (289640) STEERING ASSEMBL Y 61 steering-tex_HUSQSR_14 21 35 19 60 59 58 63 5 62 15 14 13 13 53 8 70 68 69 16 28 28 13 22 64 4 15 14 6 9 8 7 9 8 7 67 67 66 6 2 45 51 26.
39 TRACTOR - MODEL NO . YTH24V54 (289640) STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 532 41 64-80 Wheel, Steering 2 532 19 59-68 Axle Asm., F ront 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm., RH 6 532 12 49-31 Bearing, Race Thrust Harden 7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.
40 TRACTOR - MODEL NO . YTH24V54 (289640) MOWER DECK mower_dec k 54-tex_19 47 7 49 46 32 33 31 30 1 33 52 52 43 196 97 33 192 49 34 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 58 60 59 18 21 18 18 .
41 TRACTOR - MODEL NO . YTH24V54 (289640) MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 31-25 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm.
42 TRACTOR - MODEL NO . YTH24V54 (289640) MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-te x_3 91 89 87 89 87 2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-31 Lever Asm.
43 TRACTOR - MODEL NO . YTH24V54 (289640) SEA T ASSEMBL Y 1 532 42 40-68 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
44 TRACTOR - MODEL NO . YTH24V54 (289640) DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO . NO . DESCRIPTION KEY P ART NO .
45 TRACTOR - MODEL NO . YTH24V54 (289640) BRIGGS ENGINE - MODEL 445677, TYPE NUMBER 1198-B1 1058 OPERA TOR’S MANUAL 1329 REPLACEMENT ENGINE 1330 REP AIR MANUAL 48 SHORT BLOCK LIQUID GASKET AND THE B.
46 865 573 304 865A 865B 741 146 16 50 929 212 163 54 415 617 51 186 51A 617 798 42 192 1022 1 100 1029 7 36 35 33 34 868 5 883 617 40 42 40 798 5A 883 1022 1 100 1029 7 36 35 33 42 192 617 34 868 42 40 40 1 18A 11 8 601 187 216 562 505 227 278 212 635 1054 877 789 474 1059 TRACTOR - MODEL NO .
47 TRACTOR - MODEL NO . YTH24V54 (289640) BRIGGS ENGINE - MODEL 445677, TYPE NUMBER 1198-B1 276 1 127 137 104 987 95 150 1 128 105 1 126 1 124 160 1353 276 633 108 672 418 163 135 231 130 98 947 141 1.
48 TRACTOR - MODEL NO . YTH24V54 (289640) BRIGGS ENGINE - MODEL 445677, TYPE NUMBER 1198-B1 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 793564 Cylinder Assembly 2 499585 Bushing/.
49 TRACTOR - MODEL NO . YTH24V54 (289640) BRIGGS ENGINE - MODEL 445677, TYPE NUMBER 1198-B1 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 544 Armature-Starter (Service by 497595 Star.
50 TRACTOR - - MODEL NUMBER YTH24V54 (289640) TUFFTORQ TRANSAXLE MODEL NUMBER K46BT MODEL K46BT 7A646084180 33 16 20 10 34 34 35 19 13 90 95 34 76 80 81 84 87 86 8 9 15 7 82 78 82 85 83 ACTUAL P AR TS.
51 TRACTOR - - MODEL NUMBER YTH24V54 (289640) TUFFTORQ TRANSAXLE MODEL NUMBER K46BT 7 532 41 43-95 V ent V alve 15 8 532 41 43-96 Magnet 9 532 41 43-97 Magnet Holder 10 532 41 59-23 Pump Shaft/Bearing.
52 SERVICE NOTES.
53 SERVICE NOTES.
54 SERVICE NOTES.
55 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e .
04.30.10 JA Printed in the U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in m.
Een belangrijk punt na aankoop van elk apparaat Husqvarna YTH24V54 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna YTH24V54 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna YTH24V54 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna YTH24V54 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna YTH24V54 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna YTH24V54 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna YTH24V54 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna YTH24V54 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
